Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM30B0U _58 Vehicle Interior _009409 SEAT _0054863 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2651  Reclining Sensor Malfunction  


DESCRIPTION

When the position control ECU and switch assembly does not receive a sensor signal despite forward or backward movement of the seatback by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2651 Reclining Sensor Malfunction The forward and backward lock detection position of the sensor is the same.
·

Position control ECU and switch assembly

·

Reclining motor (Separate type front seatback spring assembly)

·

Harness or connector



WIRING DIAGRAM

B342142
4.729,3.875 6.75,4.302 2.021,0.427 10 false Position Control ECU and Switch Assembly 0.885,3.833 2.781,4.385 1.896,0.552 10 false Separate Type Front Seatback Spring Assembly 1.302,3.083 1.76,3.281 0.458,0.198 10 false f1 1.292,3.271 2.542,3.49 1.25,0.219 10 false Reclining Motor 2.26,1.073 2.417,1.271 0.156,0.198 10 false 4 2.229,1.573 2.385,1.771 0.156,0.198 10 false 1 2.24,2.083 2.448,2.323 0.208,0.24 10 false 2 2.229,2.573 2.385,2.771 0.156,0.198 10 false 3 4.802,1.198 5.26,1.396 0.458,0.198 10 false e18 4.802,1.698 5.26,1.896 0.458,0.198 10 false e18 4.844,2.198 5.156,2.396 0.313,0.198 10 false e6 4.844,2.698 5.156,2.896 0.313,0.198 10 false e6 4.917,0.979 5.073,1.177 0.156,0.198 10 false 9 4.854,1.49 5.156,1.688 0.302,0.198 10 false 11 4.854,1.979 5.229,2.146 0.375,0.167 10 false 11 4.885,2.51 5.042,2.708 0.156,0.198 10 false 1 5.177,1.198 5.792,1.396 0.615,0.198 10 false RCL+ 5.167,1.688 5.781,1.885 0.615,0.198 10 false RCL- 5.135,2.188 5.75,2.385 0.615,0.198 10 false SSRR 5.146,2.708 5.76,2.906 0.615,0.198 10 false SGND

PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (RECLINING MOTOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the Techstream.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Reclining Seat reclining operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Reclining
50004 162 1
OK:

Motor operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (RECLINING MOTOR CIRCUIT)

NG

5.INSPECT RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY)
2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (RECLINING MOTOR CIRCUIT)
a.
E118523
1.552,0.344 1.844,0.583 0.292,0.24 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 1.646,0.375 2.01,0.594 0.365,0.219 10 false f1
*a Front view of wire harness connector
(to Reclining Motor [Separate Type Front Seatback Spring Assembly])


Disconnect the f1 reclining motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
f1-2 - f1-3 Reclining switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

3.CHECK RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - RECLINING MOTOR)
3.CHECK RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY)
a.
B238515
1.521,0.24 1.948,0.531 0.427,0.292 0.125,0.052 0.302,0.219 0.177,0.167 10 *a 1.667,0.302 1.99,0.531 0.323,0.229 10 f1
*a Component with harness connected
(Reclining Motor [Separate Type Front Seatback Spring Assembly])


Reconnect the f1 reclining motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
f1-2 - Body ground Reclining switch on 4.5 to 4.8 V



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPLACE RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - RECLINING MOTOR)
a.

Disconnect the e6 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e6-11 (SSRR) - f1-2 Always Below 1 Ω
e6-1 (SGND) - f1-3 Always Below 1 Ω
e6-11 (SSRR) - Body ground Always 10 kΩ or higher
e6-1 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY)
a.

Remove the separate type front seatback spring assembly.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY


b.

Inspect the separate type front seatback spring assembly.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - RECLINING MOTOR)

NG

REPLACE RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - RECLINING MOTOR)
a.

Disconnect the e18 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e18-9 (RCL+) - f1-4 Always Below 1 Ω
e18-11 (RCL-) - f1-1 Always Below 1 Ω
e18-9 (RCL+) - Body ground Always 10 kΩ or higher
e18-11 (RCL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR