When the position control ECU and switch assembly does not receive a sensor signal despite upward or downward movement of the front of the seat cushion by power seat motor operation, this DTC is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2652 | Front Vertical Sensor Malfunction | The upward and downward lock detection position of the sensor is the same. | ·
Position control ECU and switch assembly ·
Front vertical motor (Separate type front seat cushion spring assembly) ·
Harness or connector |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / Driver Seat / Active Test.
Perform the Active Test according to the display on the Techstream.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Vertical Operation | Seat front vertical operation | OFF/Down/Up | - |
| Tester Display |
|---|
| Front Vertical Operation |
Motor operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Front Vertical Motor [Separate Type Front Seat Cushion Spring Assembly]) |
Disconnect the e13 front vertical motor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| e13-2 - e13-3 | Front vertical switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Front Vertical Motor [Separate Type Front Seat Cushion Spring Assembly]) |
Reconnect the e13 front vertical motor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| e13-2 - Body ground | Front vertical switch on | 4.5 to 4.8 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e6 position control ECU and switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e6-3 (SSFV) - e13-2 | Always | Below 1 Ω |
| e6-1 (SGND) - e13-3 | Always | Below 1 Ω |
| e6-3 (SSFV) - Body ground | Always | 10 kΩ or higher |
| e6-1 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the separate type front seat cushion spring assembly.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY
Inspect the separate type front seat cushion spring assembly.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e18 position control ECU and switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e18-8 (FRV+) - e13-4 | Always | Below 1 Ω |
| e18-5 (FRV-) - e13-1 | Always | Below 1 Ω |
| e18-8 (FRV+) - Body ground | Always | 10 kΩ or higher |
| e18-5 (FRV-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG