Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS
RM30B0U _59 Vehicle Exterior _010076 WINDOW / GLASS _0054874 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the ignition switch off, waiting time may be requiredbefore disconnectingthe cable from the battery terminal. Therefore, makesure to read the disconnecting thecable from the battery terminal noticebefore proceeding with work.


Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

If the windshield glass is replaced on a vehicle equipped with an lane departure alert camera, make sure to use a Toyota genuine part, as the camera may not be able to beinstalled due to a missing bracket or the lane departure alert system may not operateproperly due to a difference in the transmissivity or ceramic line shape.



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.


Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

Hide 3.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.

Partially remove the front door opening trim weatherstrip LH so that the front pillar garnish LH can be removed.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 4.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 5.REMOVE FRONT PILLAR GARNISH LH

Hide 6.REMOVE FRONT PILLAR GARNISH RH

Hide 7.REMOVE INNER REAR VIEW MIRROR ASSEMBLY

Hide 9.REMOVE ASSIST GRIP SUB-ASSEMBLY

Hide 13.REMOVE ROOF HEADLINING ASSEMBLY

HINT:

It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining.


a.

Partially remove the roof headlining assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 14.REMOVE WINDSHIELD WIPER ARM COVER

Hide 15.REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH

Hide 16.REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH

Hide 17.REMOVE FRONT FENDER TO COWL SIDE SEAL LH

Hide 18.REMOVE FRONT FENDER TO COWL SIDE SEAL RH

Hide 19.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 20.REMOVE WINDSHIELD GLASS

a.

Using a knife, cut off the windshield outside moulding as shown in the illustration.

E268572
1.583,0.667 1.583,0.333 1.583,0.333 1.333,0.333 false 4.667,0.583 4.667,0.25 4.667,0.25 4.5,0.25 false 6,1.25 5.75,1.25 false 2.667,1.167 2.417,1.167 false 1.25,1.083 1.25,1.25 false 4.208,1.281 4.625,1.281 4.625,1.281 4.625,1.188 false 1.167,0.26 1.479,0.417 0.313,0.156 10 *1 4.042,1.208 4.354,1.365 0.313,0.156 10 *2 6.042,1.177 6.354,1.333 0.313,0.156 10 *3 2.635,0.729 2.948,0.885 0.313,0.156 10 *a 4.323,0.188 4.635,0.344 0.313,0.156 10 *1 1.198,1.26 1.51,1.417 0.313,0.156 10 *2 2.698,1.094 3.01,1.25 0.313,0.156 10 *3 1.771,0.177 2.083,0.333 0.313,0.156 10 *a 5.198,0.073 5.51,0.229 0.313,0.156 10 *a 6.125,0.854 6.438,1.01 0.313,0.156 10 *a
*1 Moulding *2 Windshield Glass
*3 Vehicle Body - -
*a Cut - -



b.
E268573
2,0.833 2,0.333 true 2.917,1.667 3.167,1.917 true 0.417,1 0.917,1 true 1.135,2.938 1.135,2.604 true 2.292,2.938 2.292,2.604 true 0.833,3.667 1.25,3.667 true 3.135,1.917 3.365,2.083 0.229,0.167 10 *1 1.948,0.167 2.26,0.323 0.313,0.156 10 *2 0.24,0.927 0.552,1.083 0.313,0.156 10 *3 1.094,2.969 1.406,3.125 0.313,0.156 10 *4 1.302,3.594 1.615,3.75 0.313,0.156 10 *5 2.26,2.969 2.573,3.125 0.313,0.156 10 *4
*1 Handles
*2 Plastic Sheet
*3 Protective Tape
*4 Stopper
*5 Piano Wire


Apply protective tape to the outer surface of the vehicle body to prevent scratches.


c.

From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.


d.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

NOTICE:
·

When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

·

To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.




e.
E270264

Place matchmarks over the glass and vehicle body at the locations indicated in the illustration.

HINT:

Matchmarks do not need to be placed if not reusing the glass.



f.

Cut through the adhesive by pulling the piano wire around the glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.



g.

Disconnect the stoppers.

E270660
5.625,0.75 5.875,0.75 false 4.698,0.75 4.948,0.75 false 1.667,0.833 1.917,0.833 false 0.573,0.125 0.885,0.281 0.313,0.156 10 *A 4.271,0.146 4.583,0.302 0.313,0.156 10 *B 1.948,0.76 2.26,0.917 0.313,0.156 10 *1 4.521,0.677 4.833,0.833 0.313,0.156 10 *2 5.896,0.667 6.208,0.823 0.313,0.156 10 *1
*A for 1-piece Type *B for 2-piece Type
*1 No. 1 Windshield Glass Stopper *2 No. 2 Windshield Glass Stopper


NOTICE:
·

The No. 1 and No. 2 windshield glass stoppers are installed on the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting off the adhesive.


·

To prevent the windshield glass from falling when performing this operation, be sure to hold the windshield glass using suction cups.



HINT:

Depending on the vehicle, either 1-piece or 2-piece type stoppers may be present.



h.

Using suction cups, remove the windshield glass.

NOTICE:
·

Be careful not to drop the windshield glass sub-assembly.


·

Leave as much adhesive on the vehicle body as possible when removing thewindshield glass sub-assembly.




Hide 21.REMOVE WINDSHIELD OUTSIDE MOULDING

a.

When reusing the windshield glass:

i.

Using a scraper, remove the windshield outside moulding.

NOTICE:
E271070
0.052,0.052 0.365,0.208 0.313,0.156 10 *A
*A Back Side


·

Be careful not to damage the windshield glass.


·

Be sure to replace the windshield outside moulding with a new one.





Hide 22.REMOVE WINDOW GLASS ADHESIVE DAM

a.

When reusing the windshield glass:

i.

Using a scraper, remove the window glass adhesive dam.

NOTICE:
E270657
0.042,0.042 0.354,0.198 0.313,0.156 10 *A
*A Back Side


·

Be careful not to damage the windshield glass.


·

Be sure to replace the window glass adhesive dam with a new one.





Hide 23.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)

a.

When reusing the windshield glass:

NOTICE:
E271068
0.042,0.042 0.354,0.198 0.313,0.156 10 *A
*A Back Side


·

Be careful not to damage the windshield glass.


·

Be sure to replace the 1-piece type No. 1 windshield glass stopper with a new pair of 2-piece type No.1 and No. 2 windshield glass stoppers.



i.

Using a scraper, remove the 2 No. 1 windshield glass stoppers.



Hide 24.REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
E270685
0.042,0.052 0.354,0.208 0.313,0.156 10 *A
*A Back Side


When reusing the windshield glass:

NOTICE:
·

Be careful not to damage the windshield glass.


·

Be sure to replace the No. 2 windshield glass stoppers with new ones.



i.

Using a scraper, remove the 2 No. 2 windshield glass stoppers.



Hide 25.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
E270665

Remove the 2 No. 1 windshield glass stoppers.

i.

Be sure to replace the No. 1 windshield glass stoppers with new ones.



Hide 26.CLEAN VEHICLE BODY

E268574
2.083,1.333 2.083,1.667 false 0.427,1.344 0.427,1.677 false 2.583,0.917 2.083,1 2.083,1 2.083,1.167 true 1,0.833 0.5,0.917 0.5,0.917 0.5,1.083 true 1.052,0.75 1.365,0.906 0.313,0.156 10 *1 0.375,1.688 0.688,1.844 0.313,0.156 10 *2 2.615,0.833 2.927,0.99 0.313,0.156 10 *1 2.031,1.688 2.344,1.844 0.313,0.156 10 *2
*1 Adhesive
*2 Vehicle Body


a.

Clean and shape the contact surface of the vehicle body.

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

HINT:

Leave as much adhesive on the vehicle body as possible.


NOTICE:

Be careful not to damage the vehicle body.




b.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.