Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT
RM30B0U _58 Vehicle Interior _009988 HEATING / AIR CONDITIONING _0054977 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  REMOVAL  


PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 2. PRECAUTION

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

for Automatic Air Conditioning System:

Make sure to select FACE mode before disconnecting the cable from the negative (-) battery terminal.



Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 4.DISCONNECT AIR CONDITIONING TUBE

a.
E266370

Remove the bolt and rotate the hook connector.


b.

Disconnect the suction tube sub-assembly.


c.

Remove the O-ring from the suction tube sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



d.

Disconnect the liquid tube sub-assembly.


e.

Remove the O-ring from the liquid tube sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



Hide 5.DISCONNECT HEATER WATER HOSE

a.
E266371
2.844,1.156 3.073,0.969 true 1.271,1.958 1.615,1.656 true 3.083,0.813 3.396,0.969 0.313,0.156 10 *1 1.094,1.958 1.406,2.115 0.313,0.156 10 *2
*1 Heater Water Outlet Hose A
*2 Heater Water Inlet Hose A


Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water outlet hose A.


b.

Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water inlet hose A.

NOTICE:
·

Do not apply excessive force to the heater water outlet hose A and heater water inlet hose A.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 6.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 7.REMOVE STEERING COLUMN ASSEMBLY

Hide 8.REMOVE REAR NO. 1 AIR DUCT

E265923

a.

Detach the 8 claws and remove the rear No. 1 air duct.


Hide 9.REMOVE AIR DUCT ASSEMBLY

a.
E266372

Remove the 2 nuts and air duct assembly.


Hide 10.REMOVE DEFROSTER NOZZLE ASSEMBLY

a.

Disconnect the automatic light control sensor (solar sensor) connector and detach the 2 harness clamps.


b.
E269757

Detach the 3 hooks and remove the defroster nozzle assembly.


Hide 11.DISCONNECT INSTRUMENT PANEL WIRE

a.
E265928

Disconnect the 2 PTC heater connectors.


b.

Remove the 2 bolts and disconnect the instrument panel junction block assembly.

E266373
0.177,5.406 0.49,5.604 0.313,0.198 10 *1 5.875,3.823 6.188,4.021 0.313,0.198 10 *2 0.167,5.115 0.479,5.313 0.313,0.198 10 *1 5.865,3.146 6.177,3.344 0.313,0.198 10 *2
*1 Instrument Panel Junction Block Assembly *2 ECU Integration Box RH



c.

Remove the bolt and 2 nuts and disconnect the ECU integration box RH.


d.

Disconnect each connector.


e.

Remove the 3 bolts and disconnect each ground wire.


f.

Detach each clamp and remove the 2 bolts to disconnect the instrument panel wire.


Hide 12.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Using a clip remover, remove the clip and then fold back the front floor carpet assembly.


b.
E266375

Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.


Hide 13.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Using a clip remover, remove the clip and then fold back the front floor carpet assembly.


b.
E266376

Remove the bolt, screw, nut and No. 2 instrument panel brace sub-assembly.


Hide 14.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY

a.

Remove the 9 bolts and instrument panel reinforcement assembly.

E266377


Hide 15.REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY

a.
E265938

Detach the 2 claws and remove the No. 2 air duct sub-assembly.

NOTICE:

If any of the claws of the No. 2 air duct sub-assembly have been cracked or deformed during removal, make sure to replace the air duct with a new one. Failure to do so may cause the No. 2 air duct sub-assembly to fall off or noise to occur.



Hide 16.REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY

a.
E265939

Detach the 2 claws and remove the No. 3 air duct sub-assembly.

NOTICE:

If any of the claws of the No. 3 air duct sub-assembly have been cracked or deformed during removal, make sure to replace the air duct with a new one. Failure to do so may cause the No. 3 air duct sub-assembly to fall off or noise to occur.



Hide 17.REMOVE AIR CONDITIONER UNIT ASSEMBLY

a.

Disconnect the drain cooler hose.

E266378


b.

Remove the bolt, nut and air conditioner unit assembly.


Hide 19.REMOVE AIR CONDITIONING DUCT SUB-ASSEMBLY (for Automatic Air Conditioning System)

a.
E265943

Disengage the 2 claws and remove the air conditioning duct sub-assembly.


Hide 20.REMOVE CONSOLE MOUNTING BRACKET LH

a.
E269758

Remove the screw and console mounting bracket LH.


Hide 21.REMOVE CONSOLE MOUNTING BRACKET RH

a.
E269759

Disengage the 2 claws to remove the console mounting bracket RH.


Hide 22.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY

Hide 23.REMOVE DRAIN COOLER HOSE

a.
E265951

Remove the drain cooler hose.


Hide 24.REMOVE AIR CONDITIONING HARNESS ASSEMBLY (for Automatic Air Conditioning System)

a.

Detach each clamp.

E260965


b.

Disconnect each connector.


c.

Remove the air conditioning harness assembly as shown in the illustration.