Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2012.12–2013.11
RM30B0U _56 Audio / Visual / Telematics _009403 AUDIO / VIDEO _0054849 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  AVC-LAN Circuit  


DESCRIPTION

Each unit of the audio and visual system connected to the AVC-LAN (communication bus) transfers switch signals using the AVC-LAN.

If a short to +B or short to ground occurs in the AVC-LAN, the audio and visual system will not function normally because communication is not possible.

WIRING DIAGRAM

E271820
4.469,1.979 4.927,2.177 0.458,0.198 10 false G67 4.458,2.135 6.875,2.417 2.417,0.281 10 false Radio and Display Receiver Assembly 5.125,0.688 5.74,0.885 0.615,0.198 10 false TX2+ 5.135,1.5 5.75,1.698 0.615,0.198 10 false TX2- 4.875,0.583 5.031,0.781 0.156,0.198 10 false 5 4.813,1.396 5.125,1.594 0.313,0.198 10 false 15 1.823,0.688 2.281,0.885 0.458,0.198 10 false TX+ 2.188,0.594 2.51,0.969 0.323,0.375 10 false 8 2.188,1.375 2.344,1.573 0.156,0.198 10 false 7 1.833,1.49 2.292,1.688 0.458,0.198 10 false TX- 0.5,2.167 2.938,2.448 2.438,0.281 10 false Stereo Component Amplifier Assembly 0.51,2.021 0.969,2.219 0.458,0.198 10 false M22

CAUTION / NOTICE / HINT

NOTICE:

After replacing the radio and display receiver assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary (w/ SDARS System).


HINT:

The radio and display receiver assembly is the master unit.


PROCEDURE

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Remove the radio and display receiver assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.
E271822
1.885,1.229 2.479,0.552 true 1.563,1.938 1.844,1.563 true 2.573,0.448 3.188,0.646 0.615,0.198 10 false TX2+ 1.24,1.844 1.729,2.01 0.49,0.167 10 false TX2-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (TX2+) - 15 (TX2-) Always 60 to 80 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the M22 stereo component amplifier assembly connector.


b.

Disconnect the G67 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M22-8 (TX+) - G67-5 (TX2+) Always Below 1 Ω
M22-7 (TX-) - G67-15 (TX2-) Always Below 1 Ω
M22-8 (TX+) - Body ground Always 10 kΩ or higher
M22-7 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal operation.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal operation, the slave unit is defective and should be replaced.




Result:
Proceed to
Master unit returns to normal operation
Master unit does not return to normal operation



Master unit returns to normal operation

REPLACE MALFUNCTIONING PARTS

Master unit does not return to normal operation

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY