Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM
RM30B0U _58 Vehicle Interior _010074 SUPPLEMENTAL RESTRAINT SYSTEMS _0056337 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1783  Rear Occupant Classification Sensor RH Circuit Malfunction  


DESCRIPTION

The rear occupant classification sensor RH circuit consists of the occupant detection ECU and rear occupant classification sensor RH.

DTC B1783 is stored when a malfunction is detected in the rear occupant classification sensor RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1783 Rear Occupant Classification Sensor RH Circuit Malfunction
One of the following conditions is met:
·

Occupant detection ECU detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to +B signal in the rear occupant classification sensor RH circuit for 2 seconds.

·

Rear occupant classification sensor RH malfunction.

·

Occupant detection ECU malfunction.


·

Separate type front seat cushion spring assembly (Rear occupant classification sensor RH)

·

Front seat wire RH

·

Occupant detection ECU



HINT:
·

When DTC B1650/32 is stored as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1783 of the occupant classification system.

·

Use the Techstream to check for DTCs of the occupant detection ECU, otherwise the DTCs cannot be read.



WIRING DIAGRAM

C256403
0.125,3.396 2.635,3.583 2.51,0.188 10 false Rear Occupant Classification Sensor RH 5.406,3.385 6.979,3.552 1.573,0.167 10 false Occupant Detection ECU 5.385,3.219 5.74,3.396 0.354,0.177 10 false d15 1.583,0.635 1.938,0.813 0.354,0.177 10 false 1 1.573,1.531 1.927,1.708 0.354,0.177 10 false 2 1.583,2.438 1.938,2.615 0.354,0.177 10 false 3 5.531,0.615 5.885,0.792 0.354,0.177 10 false 2 5.51,1.563 5.865,1.74 0.354,0.177 10 false 4 5.521,2.458 5.875,2.635 0.354,0.177 10 false 6 0.115,3.229 0.469,3.406 0.354,0.177 10 false d7

CAUTION / NOTICE / HINT

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>GENERAL INFORMATION


HINT:
·

If troubleshooting (wire harness inspection) is difficult to perform, remove the front seat RH installation bolts to see the undersurface of the seat cushion.

·

In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause problems, such as seat rail deformation. Hold the seat up only for as long as necessary.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the Techstream to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1783 is not output
DTC B1783 is output


HINT:

DTCs other than DTC B1783 may be output at this time, but they are not related to this check.




DTC B1783 is not output

DTC B1783 is output

2.CHECK CONNECTION OF CONNECTOR
2.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the occupant detection ECU and rear occupant classification sensor RH.


Result:
Proceed to
Connectors are properly connected
Connectors are not properly connected



Connectors are properly connected

3.CHECK CONNECTOR

Connectors are not properly connected

CONNECT CONNECTOR

3.CHECK CONNECTOR
a.
C253897
0.688,1.365 0.889,1.535 0.201,0.17 10 *1 2.282,1.622 2.483,1.792 0.201,0.17 10 *2 1.538,0.681 1.74,0.851 0.201,0.17 10 *3
*1 Rear Occupant Classification Sensor RH
*2 Occupant Detection ECU
*3 Front Seat Wire RH


Disconnect the connectors from the occupant detection ECU and rear occupant classification sensor RH.


b.

Check that the connectors (on the occupant detection ECU side and rear occupant classification sensor RH side) are not damaged.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Proceed to
Connectors are not deformed or damaged
Connectors are deformed or damaged



Connectors are not deformed or damaged

4.CHECK FRONT SEAT WIRE RH

Connectors are deformed or damaged

REPLACE FRONT SEAT WIRE RH

4.CHECK FRONT SEAT WIRE RH
a.
E271671
0.26,3.833 0.625,4.094 0.365,0.26 0.26,2.146 0.625,2.406 0.365,0.26 2.135,1.896 2.333,1.896 false 0.99,2.948 1.188,2.948 false 1.542,0.25 1.854,0.406 0.313,0.156 10 false *1 0.844,0.865 1.156,1.021 0.313,0.156 10 false *2 2.552,1.135 2.865,1.292 0.313,0.156 10 false *3 2.385,1.823 2.698,1.979 0.313,0.156 10 false *4 2.427,2.406 2.74,2.563 0.313,0.156 10 false *5 2.594,3.979 2.906,4.135 0.313,0.156 10 false *6 0.125,1.656 0.438,1.813 0.313,0.156 10 false *a 0.135,3.521 0.448,3.677 0.313,0.156 10 false *b 0.76,2.885 1.073,3.042 0.313,0.156 10 false *4 2.292,0.427 2.604,0.583 0.313,0.156 10 false A 1.906,0.688 2.219,0.844 0.313,0.156 10 false B 1.333,0.698 1.646,0.854 0.313,0.156 10 false C 0.917,0.427 1.229,0.583 0.313,0.156 10 false D 0.323,3.875 0.635,4.031 0.313,0.156 10 false d15 0.344,2.198 0.656,2.354 0.313,0.156 10 false d7
*1 Front Seat Wire RH
*2 Rear Occupant Classification Sensor RH
*3 Occupant Detection ECU
*4 Service Wire
*5 Connector C
*6 Connector B
*a Front view of wire harness connector
(to Rear Occupant Classification Sensor RH)
*b Front view of wire harness connector
(to Occupant Detection ECU)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
d15-2 - Body ground Ignition switch ON Below 1 V
d15-4 - Body ground
d15-6 - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using service wires, connect terminals 1 and 3, and terminals 2 and 3 of connector C.

NOTICE:

Do not forcibly insert the service wires into the terminals of the connector.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d15-2 - d15-6 Always Below 1 Ω
d15-4 - d15-6



h.

Disconnect the service wires from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d15-2 - d15-6 Always 1 MΩ or higher
d15-4 - d15-6
d15-2 - d15-4
d15-2 - Body ground
d15-4 - Body ground
d15-6 - Body ground



Result:
Proceed to
OK
NG



OK

5.CHECK DTC

NG

REPLACE FRONT SEAT WIRE RH

5.CHECK DTC
a.

Connect the connectors to the occupant detection ECU and rear occupant classification sensor RH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the Techstream to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1783 is not output
DTC B1783 is output


HINT:

DTCs other than DTC B1783 may be output at this time, but they are not related to this check.




DTC B1783 is not output

DTC B1783 is output

6.REPLACE OCCUPANT DETECTION ECU
6.REPLACE OCCUPANT DETECTION ECU
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Result:
Proceed to
"Zero Point Calibration is complete." is displayed


HINT:

Perform the inspection using parts from a normal vehicle when possible.




"Zero Point Calibration is complete." is displayed

7.PERFORM ZERO POINT CALIBRATION
7.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.



Result:
Proceed to
"Zero Point Calibration is complete." is displayed
"Zero Point Calibration is complete." is not displayed



"Zero Point Calibration is complete." is displayed

8.PERFORM SENSITIVITY CHECK

"Zero Point Calibration is complete." is not displayed

10.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (REAR OCCUPANT CLASSIFICATION SENSOR RH)
8.PERFORM SENSITIVITY CHECK
a.

Perform the sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Standard:

27 to 33 kg (59.5 to 72.8 lb)



Result:
Proceed to
OK
NG



OK

9.CHECK DTC

NG

10.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (REAR OCCUPANT CLASSIFICATION SENSOR RH)
9.CHECK DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the Techstream to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1783 is not output
DTC B1783 is output


HINT:

DTCs other than DTC B1782 may be output at this time, but they are not related to this check.




DTC B1783 is not output

END (OCCUPANT DETECTION ECU WAS DEFECTIVE)

DTC B1783 is output

10.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (REAR OCCUPANT CLASSIFICATION SENSOR RH)
10.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (REAR OCCUPANT CLASSIFICATION SENSOR RH)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the separate type front seat cushion spring assembly.



HINT:

Perform the inspection using parts from a normal vehicle when possible.


Result:
Proceed to
NEXT



NEXT

11.PERFORM ZERO POINT CALIBRATION
11.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.



Result:
Proceed to
"Zero Point Calibration is complete." is displayed



"Zero Point Calibration is complete." is displayed

12.PERFORM SENSITIVITY CHECK
12.PERFORM SENSITIVITY CHECK
a.

Perform the sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Standard:

27 to 33 kg (59.5 to 72.8 lb)



Result:
Proceed to
NEXT



NEXT

END (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY [REAR OCCUPANT CLASSIFICATION SENSOR RH] WAS DEFECTIVE)