DTC B1788 is stored when the occupant detection ECU receives a collision detection signal, which is sent by the rear occupant classification sensor RH when an accident occurs.
DTC B1788 is also stored when the separate type front seat cushion spring assembly is subjected to a strong impact, even if an actual accident has not occurred.
However, when the occupant detection ECU outputs a collision detection signal, even if the vehicle has not been in a collision, DTC B1788 can be cleared by conducting the zero point calibration and sensitivity check.
Therefore, if DTC B1788 is output, first perform the zero point calibration and sensitivity check.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1788 | Rear Occupant Classification Sensor RH Collision Detection | Either condition is met:
·
Occupant detection ECU receives a collision detection signal, which is sent by the rear occupant classification sensor RH when an accident occurs. ·
Separate type front seat cushion spring assembly is subjected to a strong impact, regardless of whether or not an actual accident has occurred. |
·
Separate type front seat cushion spring assembly (Rear occupant classification sensor RH) ·
Occupant detection ECU |
When DTC B1650/32 is stored as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1788 of the occupant classification system.
Use the Techstream to check for DTCs of the occupant detection ECU, otherwise the DTCs cannot be read.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>GENERAL INFORMATION
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTC B1788 is not output |
| DTC B1788 is output |
DTCs other than DTC B1788 may be output at this time, but they are not related to this check.
DTC B1788 is not output
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DIAGNOSIS SYSTEM
DTC B1788 is output
Perform the zero point calibration.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
| Proceed to |
|---|
| "Zero Point Calibration is complete." is displayed |
| "Zero Point Calibration is complete." is not displayed |
"Zero Point Calibration is complete." is displayed
"Zero Point Calibration is complete." is not displayed
Perform the sensitivity check.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
27 to 33 kg (59.5 to 72.8 lb)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTC B1788 is not output |
| DTC B1788 is output |
DTCs other than DTC B1788 may be output at this time, but they are not related to this check.
DTC B1788 is not output
DTC B1788 is output
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the separate type front seat cushion spring assembly.
for Power Seat
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>REMOVAL
for Manual Seat
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>REMOVAL
Perform the inspection using parts from a normal vehicle when possible.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Perform the zero point calibration.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
| Proceed to |
|---|
| "Zero Point Calibration is complete." is displayed |
| "Zero Point Calibration is complete." is not displayed |
"Zero Point Calibration is complete." is displayed
"Zero Point Calibration is complete." is not displayed
Perform the sensitivity check.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
27 to 33 kg (59.5 to 72.8 lb)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.
Use the Techstream to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTC B1788 is not output |
| DTC B1788 is output |
DTCs other than DTC B1788 may be output at this time, but they are not related to this check.
DTC B1788 is not output
DTC B1788 is output
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the occupant detection ECU.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
Perform the inspection using parts from a normal vehicle when possible.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Perform the zero point calibration.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
| Proceed to |
|---|
| "Zero Point Calibration is complete." is displayed |
"Zero Point Calibration is complete." is displayed
Perform the sensitivity check.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
27 to 33 kg (59.5 to 72.8 lb)
| Proceed to |
|---|
| NEXT |
NEXT