Home › Brake › BRAKE (FRONT) › FRONT BRAKE FLEXIBLE HOSE
RM30B0U _54 Brake _010844 BRAKE (FRONT) _0057931 FRONT BRAKE FLEXIBLE HOSE A

BRAKE (FRONT)  FRONT BRAKE FLEXIBLE HOSE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT FLEXIBLE HOSE

NOTICE:

When replacing both the left and right front flexible hoses, as the left and right hoses each have a different shape, be sure to check the part number to confirm whether the hose is the left or right one before installing it.


a.
C127057

Connect the flexible hose with a new gasket and a new union bolt to the disc brake cylinder.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)

HINT:

Insert the flexible hose lock securely into the lock hole in the cylinder.



b.
C279241
1.406,1.208 1.406,0.385 1.406,0.385 1.917,0.385 false 2.198,1.26 2.198,0.74 2.198,0.74 2.448,0.74 false 3.094,2.469 3.094,2.99 false 2.01,0.323 2.188,0.479 0.177,0.156 10 *1 3.042,3.031 3.219,3.208 0.177,0.177 10 *3 2.5,0.667 2.688,0.854 0.188,0.188 10 *2 1.75,2.552 1.896,2.75 0.146,0.198 10 D 2.802,2.719 2.938,2.896 0.135,0.177 10 B 1.698,0.813 1.813,1 0.115,0.188 10 C 3.177,0.938 3.323,1.125 0.146,0.188 10 A
*1 Flexible Hose Bracket
*2 Flexible Hose Clamp
*3 Sensor Clamp


Set the flexible hose clamp on the flexible hose bracket.


c.

Simultaneously perform the following: 1) hang the hook part of the sensor clamp labeled A on the flexible hose bracket labeled C; and 2) insert the hook part of the sensor clamp labeled B into the flexible hose bracket labeled D.


d.
C278620
3.125,0.125 3.281,0.323 0.156,0.198 10 A 2.229,0.24 2.375,0.458 0.146,0.219 10 B 2.333,1.104 2.49,1.302 0.156,0.198 10 C 1.594,1.792 1.75,1.99 0.156,0.198 10 D

Install the bolt labeled C to secure the flexible hose clamp and sensor clamp.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


e.

Install the flexible hose with the bolt labeled D.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


f.

Set the flexible hose into place at the connecting point with the brake tube labeled A, and then install a new clip labeled B.


g.

Using a union nut wrench, connect the flexible hose to the brake tube labeled A while holding the flexible hose with a wrench.

Torque:
15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not bend or damage the brake tube.

·

Do not allow any foreign matter such as dirt and dust to enter the brake tube from the connecting point.

·

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




Hide 2.REMOVE COWL TOP VENTILATOR LOUVER BRACKET LH

Hide 4.INSTALL COWL TOP VENTILATOR LOUVER BRACKET LH

Hide 5.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)