This DTC is stored when a malfunction in the IG1 circuit, IG2 circuit or IG hold circuit in the certification ECU (smart key ECU assembly) is detected.
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| B2271 | Ignition Hold Monitor Malfunction | When either of the following conditions is met (1-trip detection logic*):
·
The IG1 or IG2 circuit in the certification ECU (smart key ECU assembly) is malfunctioning. ·
The IG hold circuit in the certification ECU (smart key ECU assembly) is malfunctioning. |
·
AM2 fuse ·
Certification ECU (smart key ECU assembly) ·
Wire harness or connector |
IG ON |
*: Only detected while a malfunction is present and the engine switch is on (IG)
The IG1 and IG2 circuits activate the IG1 and IG2 relays.
After the IG1 and IG2 circuits turn on, even if the CPU operates incorrectly, the IG hold circuit maintains the power source mode in on (IG).
| Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
| The engine switch cannot be turned on (IG) (the engine cannot be started). | The power source mode cannot be changed to on (IG). |
Related Data List and Active Test Items
| DTC | Data List Item | Active Test Item |
|---|---|---|
| B2271 | Power Source Control:
·
IG1 Relay Monitor(Inside) ·
IG2 Relay Monitor(Inside) ·
Latch Circuit Starting Control:
·
Ignition |
- |
When using the Techstream with the engine switch off to troubleshoot:
Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.
The smart key system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart key system (for Start Function) after confirming that the communication systems are functioning properly.
Before replacing the certification ECU (smart key ECU assembly), refer to the smart key system (for Start Function) precaution.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Start Function)>PRECAUTION
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
| *a | Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
Disconnect the G82 certification ECU (smart key ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G82-2 (+B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
Disconnect the G82 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G82-11 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G82 certification ECU (smart key ECU assembly) connector.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G82-9 (IG2D) - Body ground | Engine switch on (ACC) → Engine switch on (IG) | 1 V or less → 9 V or higher |
| G84-6 (IG1D) - Body ground |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG