If the engine switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
| Problem Symptom | Data List Item | Active Test Item |
|---|---|---|
| Power source mode does not change to on (ACC) but does change to on (IG) | Power Source Control
·
Power Supply Condition ·
ACC Relay Monitor |
- |
Refer to DTC B2274.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Start Function)>B2274
When using the Techstream with the engine switch off to troubleshoot:
Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.
The smart key system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart key system (for Start Function) after confirming that the communication systems are functioning properly.
Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.
If the smart key system is disabled through the customize function, enable the system before performing troubleshooting.
Before replacing the certification ECU (smart key ECU assembly), refer to the smart key system (for Start Function) precaution.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Start Function)>PRECAUTION
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
After completing repairs, confirm that the problem does not occur.
Disconnect the G84 connector from the certification ECU (smart key ECU assembly).
Disconnect the 3C and 3D connectors from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G84-4 (ACCD) - 3C-45 | Always | Below 1 Ω |
| 3D-9 - Body ground | ||
| G84-4 (ACCD) or 3C-45 - Body ground | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-1 - 3D-51 | Battery voltage not applied to terminals 3C-45 and 3D-9 | 10 kΩ or higher |
| Battery voltage applied to terminals 3C-45 and 3D-9 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G84 certification ECU (smart key ECU assembly) connector
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G84-4 (ACCD) - Body ground | Engine switch off → Engine switch on (ACC) | 1 V or less → 8.5 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG