Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM30B0U _58 Vehicle Interior _009872 METER / GAUGE / DISPLAY _0058007 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Malfunction  


DESCRIPTION

The fuel sender gauge assembly has a variable resistance mechanism. The resistance decreases when the fuel amount increases, and the resistance increases when the fuel amount decreases. The fuel receiver gauge changes based on the resistance of the fuel sender gauge assembly.


WIRING DIAGRAM

E270440
4.313,4.177 6.385,4.521 2.073,0.344 10 false Combination Meter Assembly 4.292,3.979 4.74,4.208 0.448,0.229 10 false G16 5.083,1.875 5.531,2.104 0.448,0.229 10 false CPU 5.531,1.385 5.979,1.615 0.448,0.229 10 false FUEL 4.583,1.063 5.031,1.292 0.448,0.229 10 false I/F 1.677,2.125 2.125,2.354 0.448,0.229 10 false V2 1.688,2.313 3.667,2.573 1.979,0.26 10 false Fuel Sender Gauge Assembly 1.896,1.573 2.052,1.76 0.156,0.188 10 false 1 3.063,1.563 3.271,1.729 0.208,0.167 10 false 2 4,1 4.271,1.167 0.271,0.167 10 false 16 4.01,1.573 4.281,1.74 0.271,0.167 10 false 15 4.281,1 4.531,1.219 0.25,0.219 10 false L 4.292,1.677 4.542,1.896 0.25,0.219 10 false E 2.104,1.573 2.396,1.74 0.292,0.167 10 false FS 2.771,1.563 3.063,1.729 0.292,0.167 10 false FE

PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (FUEL METER OPERATION)
a.

Using the Techstream, perform the Active Test.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Fuel Meter Operation Fuel receiver gauge OFF, Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full or Sender F -
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Meter Operation
50004 122 3
OK:

Fuel receiver gauge indication is normal.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING TECHSTREAM (FUEL INPUT)

NG

REPLACE COMBINATION METER ASSEMBLY

2.READ VALUE USING TECHSTREAM (FUEL INPUT)
a.

Using the Techstream, read the Data List.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel input signal Min.: 0 L, Max.: 127.5 L Current fuel level displayed -
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 122 39

Result:
Result Proceed to
Fuel level data displayed on the Techstream is almost the same as the fuel receiver gauge indication. A
Fuel level data displayed on the Techstream differs from the fuel receiver gauge indication. B



A

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SENDER GAUGE ASSEMBLY)

B

REPLACE COMBINATION METER ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SENDER GAUGE ASSEMBLY)
a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the V2 fuel sender gauge assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-16 (L) - V2-1 (FS) Always Below 1 Ω
G16-15 (E) - V2-2 (FE)
G16-16 (L) or V2-1 (FS) - Body ground Always 10 kΩ or higher
G16-15 (E) or V2-2 (FE) - Body ground



Result:
Proceed to
OK
NG



OK

4.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.

Remove the fuel sender gauge assembly.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Inspect the fuel sender gauge assembly.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY