Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM30B0U _58 Vehicle Interior _009872 METER / GAUGE / DISPLAY _0058007 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Engine Coolant Temperature Receiver Gauge Malfunction  


DESCRIPTION

In this circuit, the combination meter assembly receives engine coolant temperature signals from the ECM using the CAN communication line. Thecombination meter assembly displays the engine coolant temperature, which is calculated based on the data received from the ECM.

WIRING DIAGRAM

E200122
1.615,2.667 1.948,2.833 0.333,0.167 10 ECM 4.49,2.75 6.333,2.917 1.844,0.167 10 Combination Meter Assembly 0.802,3.365 2.521,3.563 1.719,0.198 10 : CAN Communication Line

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Proceed to
CAN communication system DTC is not output
CAN communication system DTC is output



CAN communication system DTC is not output

2.CHECK SFI SYSTEM

CAN communication system DTC is output

2.CHECK SFI SYSTEM
a.

Check if a SFI system DTC is output.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
SFI system DTC is not output
SFI system DTC is output



SFI system DTC is not output

3.PERFORM ACTIVE TEST USING TECHSTREAM (WATER TEMPERATURE METER OPERATION)

SFI system DTC is output

3.PERFORM ACTIVE TEST USING TECHSTREAM (WATER TEMPERATURE METER OPERATION)
a.

Using the Techstream, perform the Active Test.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Water Temperature Meter Operation Engine coolant temperature receiver gauge OFF, LOW, NORMAL or HIGH -
Body Electrical > Combination Meter > Active Test
Tester Display
Water Temperature Meter Operation
50004 122 89
OK:

Engine coolant temperature receiver gauge indication is normal.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING TECHSTREAM (COOLANT TEMPERATURE, COOLANT TEMP)

NG

REPLACE COMBINATION METER ASSEMBLY

4.READ VALUE USING TECHSTREAM (COOLANT TEMPERATURE, COOLANT TEMP)
a.

Using the Techstream, read the Data List.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Coolant Temperature Engine coolant temperature 0 to 127.5°C (0 to 261.5°F) After warming up: 75 to 100°C (167 to 212°F) -
Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Coolant Temp Engine coolant temperature Min.: -40°C (-40°F), Max: 215°C (419°F) 60 to 90°C (140 to 194°F): After warming up engine -
Body Electrical > Combination Meter > Data List
Tester Display
Coolant Temperature
50003 122 10
Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8
HINT:
·

When the Data List values of the ECUs match, an internal malfunction of the ECM is suspected.

·

When the Data List values of the ECUs do not match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected.




Result:
Proceed to
The Data List values of the ECUs do not match.
The Data List values of the ECUs match.



The Data List values of the ECUs do not match.

REPLACE COMBINATION METER ASSEMBLY

The Data List values of the ECUs match.

5.CHECK COMBINATION METER ASSEMBLY
5.CHECK COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new or normally functioning one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL

OK:

The operation of the tachometer returns to normal.



Result:
Proceed to
OK
NG



OK

END (COMBINATION METER ASSEMBLY WAS DEFECTIVE)

NG