Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM30B0U _58 Vehicle Interior _010074 SUPPLEMENTAL RESTRAINT SYSTEMS _0058017 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B161A/8A  Lost Communication with Front Satellite Sensor Bus  


DESCRIPTION

The front collision sensor circuit (front airbag sensor RH circuit and front airbag sensor LH circuit) is composed of the airbag sensor assembly, front airbag sensor RH and front airbag sensor LH.

The front airbag sensor RH or front airbag sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbag should be deployed.

DTC B161A/8A is stored when a malfunction is detected in the front collision sensor circuit (front airbag sensor RH circuit and front airbag sensor LH circuit).

DTC No. Detection Item DTC Detection Condition Trouble Area
B161A/8A Lost Communication with Front Satellite Sensor Bus One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front collision sensor circuit (front airbag sensor RH circuit and front airbag sensor LH circuit).

·

A front airbag sensor RH malfunction.

·

A front airbag sensor LH malfunction.

·

An airbag sensor assembly malfunction.


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor RH

·

Front airbag sensor LH

·

Airbag sensor assembly



WIRING DIAGRAM

C279109
1.313,0.854 1.667,1.042 0.354,0.188 10 false +SR 1.354,1.646 1.667,1.844 0.313,0.198 10 false -SR 3.365,0.854 3.771,1.031 0.406,0.177 10 false AG10 5.604,1.635 5.917,1.833 0.313,0.198 10 false -SR 1.354,3.438 1.667,3.625 0.313,0.188 10 false +SL 5.615,4.208 5.969,4.396 0.354,0.188 10 false -SL 5.583,3.427 5.938,3.615 0.354,0.188 10 false +SL 1.385,4.229 1.74,4.417 0.354,0.188 10 false -SL 1.688,0.729 1.865,0.885 0.177,0.156 10 false 2 1.677,4.135 1.854,4.313 0.177,0.177 10 false 1 3.563,0.646 3.74,0.823 0.177,0.177 10 false 1 3.354,1.646 3.771,1.823 0.417,0.177 10 false AG10 3.396,3.427 3.75,3.615 0.354,0.188 10 false AG9 3.417,4.229 3.771,4.417 0.354,0.188 10 false AG9 0.385,2.365 1.958,2.594 1.573,0.229 10 false Front Airbag Sensor RH 0.385,2.219 0.74,2.406 0.354,0.188 10 false A49 0.406,4.948 1.979,5.167 1.573,0.219 10 false Front Airbag Sensor LH 3.552,3.219 3.729,3.396 0.177,0.177 10 false 1 3.563,1.469 3.74,1.625 0.177,0.156 10 false 2 3.563,4.042 3.74,4.198 0.177,0.156 10 false 2 0.427,4.792 0.781,4.979 0.354,0.188 10 false A24 5.385,4.771 5.74,4.958 0.354,0.188 10 false G92 5.375,4.917 6.979,5.156 1.604,0.24 10 false Airbag Sensor Assembly 1.677,3.344 1.854,3.5 0.177,0.156 10 false 2 1.688,1.542 1.865,1.719 0.177,0.177 10 false 1 5.333,0.74 5.604,0.917 0.271,0.177 10 false 29 5.333,1.563 5.604,1.74 0.271,0.177 10 false 27 5.354,3.323 5.625,3.5 0.271,0.177 10 false 30 5.333,4.135 5.573,4.313 0.24,0.177 10 false 28 5.573,0.833 5.927,1.021 0.354,0.188 10 false +SR 3.406,1.073 3.813,1.25 0.406,0.177 10 false +SR 3.438,1.875 3.844,2.052 0.406,0.177 10 false -SR 3.406,3.635 3.813,3.813 0.406,0.177 10 false +SL 3.427,4.469 3.833,4.646 0.406,0.177 10 false -SL

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Turn the ignition switch off.

HINT:

If a communication error occurs, DTCs for both the LH and RH sides will be stored simultaneously. To identify the malfunctioning area, turn the ignition switch off and then to ON again.



c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1613/83 is output
DTC B1618/84 is output
DTCs B1613/83 and B1618/84 are not output


HINT:
·

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the ignition switch off and then to ON again.

·

Codes other than DTCs B1613/83 and B1618/84 may be output at this time, but they are not related to this check.





DTC B1613/83 is output

DTC B1618/84 is output

DTCs B1613/83 and B1618/84 are not output

2.CHECK AIRBAG SENSOR ASSEMBLY
2.CHECK AIRBAG SENSOR ASSEMBLY
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B161A/8A is not output
DTC B161A/8A is output


HINT:

Codes other than DTC B161A/8A may be output at this time, but they are not related to this check.




DTC B161A/8A is not output

DTC B161A/8A is output