Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM30B0U _58 Vehicle Interior _010074 SUPPLEMENTAL RESTRAINT SYSTEMS _0058017 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1805/52  Short in Front Passenger Side Squib Circuit  B1806/52  Open in Front Passenger Side Squib Circuit  B1807/52  Short to GND in Front Passenger Side Squib Circuit  B1808/52  Short to B+ in Front Passenger Side Squib Circuit  


DESCRIPTION

The front passenger side squib circuit consists of the airbag sensor assembly and instrument panel passenger airbag assembly.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1805/52 Short in Front Passenger Side Squib Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal 5 times in the front passenger side squib circuit during the primary check.

·

A front passenger side squib malfunction.

·

An airbag sensor assembly malfunction.


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Airbag sensor assembly


B1806/52 Open in Front Passenger Side Squib Circuit One of the following conditions is met:
·

The airbag sensor assembly detects an open circuit signal in the front passenger side squib circuit for 2 seconds.

·

A front passenger side squib malfunction.

·

An airbag sensor assembly malfunction.


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Airbag sensor assembly


B1807/52 Short to GND in Front Passenger Side Squib Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to ground signal in the front passenger side squib circuit for 0.5 seconds.

·

A front passenger side squib malfunction.

·

An airbag sensor assembly malfunction.


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Airbag sensor assembly


B1808/52 Short to B+ in Front Passenger Side Squib Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to B+ signal in the front passenger side squib circuit for 0.5 seconds.

·

A front passenger side squib malfunction.

·

An airbag sensor assembly malfunction.


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Airbag sensor assembly



WIRING DIAGRAM

C253311
5.813,0.99 6.042,1.156 0.229,0.167 10 false P+ 5.813,2.208 6.042,2.375 0.229,0.167 10 false P- 3.313,1.198 3.542,1.365 0.229,0.167 10 false P+ 3.313,2.417 3.542,2.583 0.229,0.167 10 false P- 1.354,0.927 1.583,1.094 0.229,0.167 10 false P+ 1.354,2.135 1.583,2.302 0.229,0.167 10 false P- 5.625,0.927 5.75,1.083 0.125,0.156 10 false 4 5.625,2.135 5.75,2.292 0.125,0.156 10 false 3 5.49,2.99 5.875,3.135 0.385,0.146 10 false G92 5.51,3.135 7.073,3.417 1.563,0.281 10 false Airbag Sensor Assembly 3.375,0.792 3.479,0.958 0.104,0.167 10 false 1 1.615,2.115 1.719,2.281 0.104,0.167 10 false 1 3.375,2 3.479,2.167 0.104,0.167 10 false 2 1.604,0.917 1.708,1.083 0.104,0.167 10 false 2 3.292,1.01 3.573,1.177 0.281,0.167 10 false Gb1 3.271,2.208 3.552,2.375 0.281,0.167 10 false Gb1 0.188,3.031 0.375,3.188 0.188,0.156 10 false b1 0.177,3.198 3.083,3.604 2.906,0.406 10 false Instrument Panel Passenger Airbag Assembly (Front Passenger Side Squib)

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:

To perform the simulation method, enter check mode (signal check) with the Techstream (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)
a.
C252988
0.385,2.135 0.813,2.344 0.427,0.208 2.031,2.656 2.26,2.729 false 1.5,2.76 1.24,2.865 false 0.458,0.458 0.771,0.615 0.313,0.156 10 false *1 2.313,1.281 2.625,1.438 0.313,0.156 10 false *2 2.417,2.271 2.729,2.427 0.313,0.156 10 false *3 0.25,1.635 0.563,1.792 0.313,0.156 10 false *a 1.021,2.802 1.333,2.958 0.313,0.156 10 false *b 1.917,0.656 2.229,0.813 0.313,0.156 10 false A 1.427,0.906 1.74,1.063 0.313,0.156 10 false C 1.26,0.896 1.573,1.052 0.313,0.156 10 false D 0.906,0.906 1.219,1.063 0.313,0.156 10 false E 0.698,0.906 1.01,1.063 0.313,0.156 10 false F 0.51,2.156 0.792,2.385 0.281,0.229 10 false b1 2.302,2.698 2.573,2.917 0.271,0.219 10 false *4
*1 Front Passenger Side Squib
*2 Airbag Sensor Assembly
*3 Connector E
*4 SST
*a Front view of wire harness connector
(to Front Passenger Side Squib)
*b Color: Orange


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the instrument panel passenger airbag assembly.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (orange connector).

CAUTION:

Never connect the tester to the instrument panel passenger airbag assembly (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output
DTC B1805/52, B1806/52, B1807/52 or B1808/52 is output


HINT:

Codes other than DTC B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.



k.

Turn the ignition switch off.


l.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


m.

Disconnect SST from connector E.



DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is output

2.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly.


b.
C208248
0.385,0.813 0.698,0.969 0.313,0.156 10 false *1 2.406,1.708 2.719,1.865 0.313,0.156 10 false *2 2.177,1.021 2.49,1.177 0.313,0.156 10 false A 1.74,1.354 2.052,1.51 0.313,0.156 10 false B 1.354,1.354 1.667,1.51 0.313,0.156 10 false C 1.208,1.354 1.521,1.51 0.313,0.156 10 false D 0.833,1.354 1.146,1.51 0.313,0.156 10 false E 0.563,1.354 0.875,1.51 0.313,0.156 10 false F
*1 Front Passenger Side Squib
*2 Airbag Sensor Assembly


Check that the connectors (on the airbag sensor assembly side and instrument panel passenger airbag assembly side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
a.
C252989
0.635,1.875 1.021,2.135 0.385,0.26 1.76,2.156 2.094,2.365 true 1.635,2.167 1.292,2.344 true 1.521,2.76 1.292,2.875 true 0.51,0.479 0.823,0.635 0.313,0.156 10 false *1 2.5,1.313 2.813,1.469 0.313,0.156 10 false *2 1.615,1.604 1.927,1.76 0.313,0.156 10 false *3 0.74,1.438 1.052,1.594 0.313,0.156 10 false *a 1.135,2.833 1.448,2.99 0.313,0.156 10 false *b 2.24,0.667 2.552,0.823 0.313,0.156 10 false A 1.854,0.948 2.031,1.146 0.177,0.198 10 false B 1.469,0.938 1.646,1.135 0.177,0.198 10 false C 1.344,0.938 1.521,1.135 0.177,0.198 10 false D 0.979,0.927 1.156,1.125 0.177,0.198 10 false E 0.75,0.938 0.927,1.135 0.177,0.198 10 false F 2.156,2.292 2.635,2.51 0.479,0.219 10 false P+ 1.094,2.26 1.406,2.427 0.313,0.167 10 false P- 0.76,1.927 1.24,2.146 0.479,0.219 10 false b1
*1 Front Passenger Side Squib
*2 Airbag Sensor Assembly
*3 Connector E
*a Front view of wire harness connector
(to Front Passenger Side Squib)
*b Color: Orange


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
b1-2 (P+) - Body ground Ignition switch ON Below 1 V
b1-1 (P-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b1-2 (P+) - b1-1 (P-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b1-2 (P+) - b1-1 (P-) Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b1-2 (P+) - Body ground Always 1 MΩ or higher
b1-1 (P-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK AIRBAG SENSOR ASSEMBLY

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK AIRBAG SENSOR ASSEMBLY
a.
C146252
0.847,0.924 0.967,1.073 0.12,0.149 10 F 0.965,0.923 1.106,1.086 0.141,0.163 10 E 1.323,0.926 1.451,1.075 0.128,0.149 10 D 1.452,0.926 1.58,1.089 0.128,0.163 10 C 1.827,1.438 2.002,1.601 0.175,0.163 10 *2 0.644,1.438 0.824,1.59 0.179,0.153 10 *1 0.733,0.834 0.731,1.365 false
*1 Front Passenger Side Squib
*2 Airbag Sensor Assembly


Connect the connectors to the instrument panel passenger airbag assembly and airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output
DTC B1805/52, B1806/52, B1807/52 or B1808/52 is output


HINT:

Codes other than DTC B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.




DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is output

5.CHECK INSTRUMENT PANEL WIRE
a.
C252990
0.313,2.438 0.698,2.708 0.385,0.271 0.813,2.979 1.323,2.896 false 0.938,3.219 1.51,2.927 false 0.385,0.563 0.698,0.719 0.313,0.156 10 false *1 0.948,0.563 1.26,0.719 0.313,0.156 10 false *2 1.448,0.552 1.76,0.708 0.313,0.156 10 false *3 2.188,1.302 2.5,1.458 0.313,0.156 10 false *4 2.573,2.469 2.885,2.625 0.313,0.156 10 false *5 1.542,1.979 1.854,2.135 0.313,0.156 10 false *a 0.365,2.49 0.781,2.708 0.417,0.219 10 false Gb1 0.573,2.896 0.885,3.083 0.313,0.188 10 false P+ 0.729,3.167 1.042,3.354 0.313,0.188 10 false P- 2,0.76 2.208,0.948 0.208,0.188 10 false A 1.677,0.979 1.885,1.167 0.208,0.188 10 false B 1.354,0.99 1.563,1.177 0.208,0.188 10 false C 1.167,0.99 1.375,1.177 0.208,0.188 10 false D 0.844,0.99 1.052,1.177 0.208,0.188 10 false E 0.635,0.979 0.844,1.167 0.208,0.188 10 false F
*1 Front Passenger Side Squib
*2 No. 2 Instrument Panel Wire
*3 Instrument Panel Wire
*4 Airbag Sensor Assembly
*5 Connector C
*a Front view of wire harness connector
(to No. 2 Instrument Panel Wire)


Disconnect the instrument panel wire connector from the No. 2 instrument panel wire.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Gb1-1 (P+) - Body ground Ignition switch ON Below 1 V
Gb1-2 (P-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Gb1-1 (P+) - Gb1-2 (P-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Gb1-1 (P+) - Gb1-2 (P-) Always 1 MΩ or higher



j.

Restore the released activation prevention mechanism of connector B to its original condition.


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Gb1-1 (P+) - Body ground Always 1 MΩ or higher
Gb1-2 (P-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE