Home › Drivetrain › GF1A TRANSFER / 4WD / AWD › DYNAMIC TORQUE CONTROL AWD SYSTEM
RM30B0U _52 Drivetrain _009983 GF1A TRANSFER / 4WD / AWD _0058072 DYNAMIC TORQUE CONTROL AWD SYSTEM C

GF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL AWD SYSTEM  C1296/96  ABS Malfunction  


DESCRIPTION

If a malfunction in the speed sensor signal circuit or acceleration sensor (airbag sensor assembly) circuit occurs, the 4WD ECU assembly will output this DTC.

The airbag sensor assembly has a built-in acceleration sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1296/96 ABS Malfunction When one of the following conditions is met:
1.

Wheel speed sensor malfunction is received from the skid control ECU (brake actuator assembly)

2.

Acceleration sensor (airbag sensor assembly) malfunction is received from skid control ECU (brake actuator assembly


·

Brake control system (Speed sensor circuit)

·

Skid control ECU (Brake actuator assembly)

·

Acceleration sensor (airbag sensor assembly) circuit

·

4WD ECU assembly



WIRING DIAGRAM

C284324
3.677,0.406 3.979,0.594 0.302,0.188 10 false FR+ 3.698,0.771 4.01,0.969 0.313,0.198 10 false FR- 4.063,0.292 4.198,0.49 0.135,0.198 10 false 7 4.063,0.708 4.219,0.906 0.156,0.198 10 false 6 5.5,0.281 5.656,0.479 0.156,0.198 10 false 1 5.5,0.688 5.656,0.885 0.156,0.198 10 false 2 5.688,0.396 6.146,0.594 0.458,0.198 10 false FR+ 5.656,0.771 6.115,0.969 0.458,0.198 10 false FR- 5.24,1.01 5.698,1.208 0.458,0.198 10 false A43 5.25,1.177 6.813,1.427 1.563,0.25 10 false Front Speed Sensor RH 3.698,1.729 3.99,1.906 0.292,0.177 10 false FL+ 3.75,2.083 3.99,2.302 0.24,0.219 10 false FL- 4.052,1.635 4.365,1.833 0.313,0.198 10 false 19 4.052,2.021 4.365,2.219 0.313,0.198 10 false 18 5.5,1.625 5.656,1.823 0.156,0.198 10 false 1 5.677,1.74 6.135,1.938 0.458,0.198 10 false FL+ 5.677,2.052 5.99,2.25 0.313,0.198 10 false FL- 5.5,2 5.656,2.198 0.156,0.198 10 false 2 5.25,2.313 5.625,2.521 0.375,0.208 10 false A14 5.271,2.5 6.76,2.719 1.49,0.219 10 false Front Speed Sensor LH 3.635,3.042 3.969,3.229 0.333,0.188 10 false RR+ 4.052,2.938 4.365,3.135 0.313,0.198 10 false 17 3.656,3.396 3.969,3.594 0.313,0.198 10 false RR- 4.063,3.313 4.375,3.51 0.313,0.198 10 false 16 5.49,2.938 5.646,3.135 0.156,0.198 10 false 1 5.49,3.323 5.646,3.521 0.156,0.198 10 false 2 5.698,3.042 6.156,3.24 0.458,0.198 10 false RR+ 5.688,3.375 6,3.573 0.313,0.198 10 false RR- 5.229,3.604 5.573,3.792 0.344,0.188 10 false M20 5.25,3.771 6.688,3.958 1.438,0.188 10 false Rear Speed Sensor RH 3.667,4.292 3.979,4.49 0.313,0.198 10 false RL+ 3.719,4.688 4.031,4.885 0.313,0.198 10 false RL- 4.073,4.188 4.24,4.354 0.167,0.167 10 false 5 4.052,4.594 4.208,4.792 0.156,0.198 10 false 4 5.49,4.188 5.646,4.385 0.156,0.198 10 false 1 5.5,4.583 5.656,4.781 0.156,0.198 10 false 2 5.688,4.292 6.146,4.49 0.458,0.198 10 false RL+ 5.719,4.656 6.177,4.854 0.458,0.198 10 false RL- 5.26,4.896 5.573,5.104 0.313,0.208 10 false N11 5.26,5.094 6.698,5.281 1.438,0.188 10 false Rear Speed Sensor LH 0.365,6.75 1.75,6.948 1.385,0.198 10 false 4WD ECU Assembly 2.646,6.875 3.104,7.073 0.458,0.198 10 false A64 2.656,7.073 4.177,7.448 1.521,0.375 10 false Skid Control ECU (Brake Actuator Assembly) 3.094,7.781 4.844,8.177 1.75,0.396 10 false Acceleration Sensor (Airbag Sensor Assembly) 0.771,8.385 2.469,8.583 1.698,0.198 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK FOR DTC (BRAKE CONTROL SYSTEM)
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRAC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON again.


d.

Drive the vehicle, accelerate to a speed of 20 km/h (12 mph) or more, and check if the speed sensor DTC (brake control system DTC) is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105
Result:
Result Proceed to
Brake control system DTC (speed sensor or acceleration sensor DTC) is not output A
Brake control system DTC (speed sensor or acceleration sensor DTC) is output B


HINT:

When DTCs indicating a CAN communication system malfunction are output, repair the CAN communication system before repairing each corresponding sensor.




A

2.READ VALUE USING TECHSTREAM (WHEEL SPEED)

B

REPAIR CIRCUIT INDICATED BY OUTPUT CODE (BRAKE CONTROL SYSTEM)

2.READ VALUE USING TECHSTREAM (WHEEL SPEED)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Chassis / Four Wheel Drive / Data List.


e.

Read the value displayed on the Techstream.

Chassis > Four Wheel Drive > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) No large fluctuations when driving at a constant speed.
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) No large fluctuations when driving at a constant speed.
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) No large fluctuations when driving at a constant speed.
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) No large fluctuations when driving at a constant speed.
Chassis > Four Wheel Drive > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
50003 118 1,2,3,4
OK:

The speed value output from the speed sensor displayed on the Techstream is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING TECHSTREAM (FORWARD AND REARWARD G)

NG

GO TO BRAKE CONTROL SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

3.READ VALUE USING TECHSTREAM (FORWARD AND REARWARD G)
a.

Enter the following menus: Chassis / Four Wheel Drive / Data List.


b.

Read the value displayed on the Techstream.

Chassis > Four Wheel Drive
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Forward and Rearward G Forward and Rearward G Min.: -25.10 m/s2
Max.: 24.90 m/s2
Approximately 0 +/-0.13 m/s2 while stationary Changes in proportion with acceleration during acceleration/deceleration.
Chassis > Four Wheel Drive > Data List
Tester Display
Forward and Rearward G
50003 118 15
OK:

The acceleration sensor (airbag sensor assembly) output value is normal.



Result:
Proceed to
OK
NG



OK

NG

GO TO BRAKE CONTROL SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)