Home › Drivetrain › GF1A TRANSFER / 4WD / AWD › DYNAMIC TORQUE CONTROL AWD SYSTEM
RM30B0U _52 Drivetrain _009983 GF1A TRANSFER / 4WD / AWD _0058072 DYNAMIC TORQUE CONTROL AWD SYSTEM D

GF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL AWD SYSTEM  DTC CHECK / CLEAR  


CHECK DTC (When Using Techstream)


a.

Check the DTCs.

i.

Connect the Techstream to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the Techstream on.


iv.

Read the DTCs following the prompts on the Techstream screen. Enter the following menus: Chassis / Four Wheel Drive / Trouble Codes.

Chassis > Four Wheel Drive > Trouble Codes
50001 118




CLEAR DTC (When Using Techstream)


a.

Clear the DTCs.

i.

Connect the Techstream to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the Techstream on.


iv.

Operate the Techstream to clear the DTCs. Enter the following menus: Chassis / Four Wheel Drive / Trouble Codes.

Chassis > Four Wheel Drive > Clear DTCs
50002 118

v.

According to the display on the Techstream, select the trouble code data display with the clear button.




CHECK DTC (When Using SST Check Wire)


a.
C166029
0.135,1.01 0.563,1.313 0.427,0.302 1.635,0.875 1.854,0.313 false 1.979,1.875 1.813,1.427 false 1.823,0.135 2.188,0.313 0.365,0.177 10 CG 0.125,0.073 0.344,0.25 0.219,0.177 10 *a 0.208,1.073 0.531,1.25 0.323,0.177 10 G14 1.885,1.875 2.25,2.052 0.365,0.177 10 TC
*a Front view of DLC3


Check the DTCs.

i.

Using SST, connect terminals TC (13) and CG (4) of the DLC3.

SST
09843-18040  


ii.

Turn the ignition switch to ON.


iii.

Read the DTCs from the AWD warning light on the combination meter.

HINT:
·

If the AWD warning light does not blink, perform relevant troubleshooting procedures. The relevant troubleshooting procedures are in the sections listed in the table below.

·

When the system is operating correctly, each light will blink continuously in a pattern of 0.25 seconds on, then 0.25 seconds off.

·

When one DTC is output, each light will output the same code at 4-second intervals. (For example, Code 21 would be output as 2 flashes, a 1.5-second pause, and then 1 flash).

·

When 2 or more DTCs are output, each light will output a different code at 2.5-second intervals, and when all codes have been output, there will be a 4-second pause and the sequence will repeat.

·

When multiple codes are set, they are output in order starting with the lowest DTC number.

·

DTCs are explained in "DIAGNOSTIC TROUBLE CODE CHART".

Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL AWD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

Section Title See Procedure
AWD Warning Light does not Come ON (Click here)
TC and CG Terminal Circuit (Click here)






CLEAR DTC (When Using SST Check Wire)


a.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


b.

Turn the ignition switch to ON.


c.
C108863

Clear the DTCs stored in the 4WD ECU assembly by depressing the brake pedal 8 times or more within 5 seconds.


d.

Check that the warning light blinks in the normal system code pattern.


e.

Remove SST from the terminals of the DLC3.


f.

Turn the ignition switch off.

HINT:

DTCs cannot be cleared by disconnecting the cable from the negative (-) battery terminal or removing the ECU-IG NO. 1 fuse.