Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM30B0U _54 Brake _010842 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0058073 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  VSC OFF Indicator Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch (traction control switch) turns off traction control and pressing and holding this switch turns off traction and VSC controls. If traction control turns OFF, the TRAC OFF indicator light will come on.

If VSC and traction control turns OFF, the TRAC OFF indicator and VSC OFF indicator light will come on.

The VSC OFF indicator light is illuminated when the VSC and TRAC controls are prohibited by operating the VSC OFF switch (traction control switch).

By pressing the VSC OFF switch (traction control switch) for 3 seconds or more, the VSC OFF mode is activated, the VSC and TRAC controls are prohibited, and both the VSC OFF indicator light and the TRAC OFF indicator light in the combination meter are illuminated.

WIRING DIAGRAM

C279159
3.385,2.573 3.844,2.771 0.458,0.198 10 false G51 3.396,2.74 5.073,3.51 1.677,0.771 10 false VSC OFF Switch (Traction Control Switch) 3.406,2.354 3.615,2.583 0.208,0.229 10 false E 4.031,2.344 4.219,2.573 0.188,0.229 10 false + 3.24,2.167 3.427,2.417 0.188,0.25 10 false 3 4.198,2.167 4.396,2.406 0.198,0.24 10 false 6 5.406,2.167 5.719,2.365 0.313,0.198 10 false 30 5.656,2.26 6.115,2.458 0.458,0.198 10 false CSW 5.51,2.823 5.969,3.021 0.458,0.198 10 false A64 5.51,3 7.115,3.531 1.604,0.531 10 false Skid Control ECU (Brake Actuator Assembly) 1.75,0.573 2.323,0.833 0.573,0.26 10 false CAN I/F 0.906,1.042 1.365,1.24 0.458,0.198 10 false CPU 1.063,2.948 1.813,3.229 0.75,0.281 10 false VSC OFF 1.771,3.438 2.052,3.698 0.281,0.26 10 false IG 0.594,3.958 2.552,4.281 1.958,0.323 10 false Combination Meter Assembly 0.979,4.406 2.948,4.698 1.969,0.292 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CAN COMMUNICATION SYSTEM

NG

CONNECT CONNECTOR TO ECU CORRECTLY

2.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

3.INSPECT BATTERY

DTC is output

3.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (CSW TERMINAL)

NG

4.CHECK HARNESS AND CONNECTOR (CSW TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the A64 skid control ECU (brake actuator assembly) connector.


c.
C199357
1.625,0.083 2,0.333 0.375,0.25 1.781,1.844 1.854,1.396 false 0,0 0.313,0.156 0.313,0.156 10 false *a 1.688,0.125 2.146,0.323 0.458,0.198 10 false A64 1.604,1.865 2.063,2.073 0.458,0.208 10 false CSW
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A64-30 (CSW) - Body ground VSC OFF switch held on Below 1 Ω
A64-30 (CSW) - Body ground VSC OFF switch off (Not pressed) 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING TECHSTREAM (TRAC/VSC OFF MODE)

NG

6.INSPECT TRACTION CONTROL SWITCH
5.READ VALUE USING TECHSTREAM (TRAC/VSC OFF MODE)
a.

Reconnect the A64 skid control ECU (brake actuator assembly) connector.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the Techstream on.


e.

Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.


f.

According to the display on the Techstream, read the Data List.

Chassis > ABS/VSC/TRAC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRAC/VSC Off Mode TRAC/VSC off mode Normal, TRAC OFF, Unknown or VSC OFF Normal: Normal mode
TRAC OFF: TRAC off mode
VSC OFF: VSC off mode
Unknown: Unspecified
Chassis > ABS/VSC/TRAC > Data List
Tester Display
TRAC/VSC Off Mode
50003 105 282

g.

Check that the mode display changes according to the VSC OFF switch (traction control switch) operation.

OK:

Display changes according to the switch operation.



Result:
Proceed to
OK
NG



OK

NG

6.INSPECT TRACTION CONTROL SWITCH
a.

Remove the VSC OFF switch (traction control switch).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>REMOVAL


b.

Inspect the VSC OFF switch (traction control switch).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - TRACTION CONTROL SWITCH)

NG

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - TRACTION CONTROL SWITCH)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-30 (CSW) - G51-6 (+) Always Below 1 Ω
G51-3 (E) - Body ground Always Below 1 Ω
A64-30 (CSW) or G51-6 (+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR