Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM30B0U _54 Brake _010842 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0058073 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display the DTC by blinking the ABS warning light and slip indicator light.

WIRING DIAGRAM

C243297
0.5,2.177 0.948,2.417 0.448,0.24 10 false ECM 0.5,2.021 1.479,2.281 0.979,0.26 10 false A62 1.094,1.542 1.323,1.698 0.229,0.156 10 false TC 5.333,1.49 6.865,1.979 1.531,0.49 10 false Skid Control ECU (Brake Actuator Assembly) 5.396,2.563 5.583,2.708 0.188,0.146 10 false 13 5.458,2.948 5.552,3.083 0.094,0.135 10 false 4 5.646,2.656 5.854,2.802 0.208,0.146 10 false TC 5.656,3.031 5.885,3.177 0.229,0.146 10 false CG 5.594,3.583 5.958,3.802 0.365,0.219 10 false G14 5.594,3.74 6.104,3.979 0.51,0.24 10 false DLC3 1.198,4.365 2.865,4.521 1.667,0.156 10 false : CAN Communication Line 1.396,1.427 2.021,1.719 0.625,0.292 10 false 23

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

2.INSPECT DLC3

DTC is output

2.INSPECT DLC3
a.
C146309
0.104,1.375 0.5,1.635 0.396,0.26 1.656,0.802 1.969,0.302 1.969,0.302 2.094,0.302 false 1.875,1.469 1.563,2.021 1.563,2.021 1.438,2.021 false 0.125,0.083 0.427,0.229 0.302,0.146 10 *a 2.156,0.208 2.458,0.354 0.302,0.146 10 CG 1.177,1.948 1.479,2.094 0.302,0.146 10 TC 0.177,1.427 0.51,1.635 0.333,0.208 10 G14
*a DLC3


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G14-13 (TC) - G14-4 (CG) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

5.INSPECT ECM (TC of DLC3 INPUT)

NG

3.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
3.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the A62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-13 (TC) - A62-23 (TC) Always Below 1 Ω
G14-13 (TC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.

Reconnect the A62 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT ECM (TC of DLC3 INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ECM (TC of DLC3 INPUT)
a.
C146309
0.104,1.375 0.5,1.635 0.396,0.26 1.656,0.802 1.969,0.302 1.969,0.302 2.094,0.302 false 1.875,1.469 1.563,2.021 1.563,2.021 1.438,2.021 false 0.125,0.083 0.427,0.229 0.302,0.146 10 *a 2.156,0.208 2.458,0.354 0.302,0.146 10 CG 1.177,1.948 1.479,2.094 0.302,0.146 10 TC 0.177,1.427 0.51,1.635 0.333,0.208 10 G14
*a DLC3


Turn the ignition switch off.


b.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.


SST
09843-18040  

c.

Turn the ignition switch to ON.


d.

Check that the malfunction indicator lamp is blinking.


Result:
Proceed to
Malfunction indicator lamp is blinking
Malfunction indicator lamp is not blinking



Malfunction indicator lamp is blinking

Malfunction indicator lamp is not blinking