Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM30B0U _54 Brake _010842 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0058073 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1225  SM Solenoid Circuit  C1468  SFR Solenoid Circuit  C1469  SFL Solenoid Circuit  C146A  SRR Solenoid Circuit  C146B  SRL Solenoid Circuit  


DESCRIPTION

These solenoids turn on when signals are received from the skid control ECU (brake actuator assembly) and they control the pressure acting on the wheel cylinders to control the braking force.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1225 SM Solenoid Circuit When any of the following is detected:
1.

While outputting switching solenoid (SM1 or SM2) ON, overcurrent continues for 0.1 seconds or more.

2.

While outputting switching solenoid (SM1 or SM2) OFF, an open circuit continues for 0.05 seconds or more.

3.

While outputting switching solenoid (SM1 or SM2) ON, an open circuit continues for 0.05 seconds or more.

4.

While outputting switching solenoid (SM1 or SM2) OFF, current continues to be applied for 0.05 seconds or more.

5.

A condition in which the outputs from switching solenoids 1 and 2 are different continues for 0.2 seconds or more.


Brake actuator assembly
C1468 SFR Solenoid Circuit Open or short in the solenoid circuit continues for 0.05 seconds or more. Brake actuator assembly
C1469 SFL Solenoid Circuit Open or short in the solenoid circuit continues for 0.05 seconds or more. Brake actuator assembly
C146A SRR Solenoid Circuit Open or short in the solenoid circuit continues for 0.05 seconds or more. Brake actuator assembly
C146B SRL Solenoid Circuit Open or short in the solenoid circuit continues for 0.05 seconds or more. Brake actuator assembly

WIRING DIAGRAM

C283799
4.531,0.792 5.469,0.979 0.938,0.188 10 false Solenoid Relay 1.594,1.375 2.969,1.573 1.375,0.198 10 false ABS NO. 2 3.25,1.094 3.563,1.292 0.313,0.198 10 false 12 3.521,1.104 3.979,1.302 0.458,0.198 10 false +BS 0.156,1.198 0.927,1.417 0.771,0.219 10 false from Battery 5.958,1.594 6.365,1.771 0.406,0.177 10 false SFRH 5.979,2.156 6.594,2.354 0.615,0.198 10 false SFLH 5.938,2.688 6.552,2.885 0.615,0.198 10 false SRRH 5.927,3.156 6.542,3.354 0.615,0.198 10 false SRLH 5.917,3.667 6.531,3.865 0.615,0.198 10 false SFRR 5.938,4.177 6.552,4.375 0.615,0.198 10 false SFLR 5.927,4.677 6.542,4.875 0.615,0.198 10 false SRRR 5.938,5.177 6.552,5.375 0.615,0.198 10 false SRLR 6.01,5.667 6.469,5.865 0.458,0.198 10 false SM1 6.031,6.188 6.49,6.385 0.458,0.198 10 false SM2 3.302,4.969 3.458,5.167 0.156,0.198 10 false 1 3.552,5.104 4.167,5.302 0.615,0.198 10 false GND1 4.427,3.104 5.552,3.26 1.125,0.156 10 false Skid Control ECU 3.896,7.854 4.354,8.052 0.458,0.198 10 false A64 3.875,8.042 5.49,8.365 1.615,0.323 10 false Brake Actuator Assembly

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.RECONFIRM DTC
HINT:

These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).

The solenoid circuits are in the skid control ECU (brake actuator assembly).

Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the skid control ECU (brake actuator assembly).


a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRAC > Clear DTCs
50002 105

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


d.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105
Result:
Proceed to
DTC is not output
DTC is output


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly), with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness from the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.





DTC is not output

DTC is output