Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM30B0U _54 Brake _010842 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0058073 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1425  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) detects the brake operating conditions through a signal transmitted by the stop light switch.

The skid control ECU (brake actuator assembly) has an open detection circuit, which outputs this DTC when detecting an open in the stop light input line or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).

DTC No. Detection Item DTC Detection Condition Trouble Area
C1425 Open in Stop Light Switch Circuit When IG1 terminal voltage is between 9.5 and 17.4 V, an open stop light switch circuit (A to B, A to body ground) continues for 0.3 seconds or more.
·

Stop light switch circuit

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C283802
1.344,1.135 3.177,1.333 1.833,0.198 10 false from Battery 1.167,2.313 1.615,2.5 0.448,0.188 10 false STOP 2.042,1.99 2.177,2.198 0.135,0.208 10 false 2 3.188,1.979 3.344,2.177 0.156,0.198 10 false 1 1.865,2.385 2.177,2.583 0.313,0.198 10 false A5 1.854,2.573 3.625,2.802 1.771,0.229 10 false Stop Light Switch Assembly 3.979,4.01 5.188,4.458 1.208,0.448 10 false Center Stop Light Assembly 5.781,2.406 6.76,2.896 0.979,0.49 10 false Open Detection Circuit 5.646,1.958 6.104,2.156 0.458,0.198 10 false STP 5.365,1.979 5.521,2.177 0.156,0.198 10 false 2 5.375,2.25 5.531,2.448 0.156,0.198 10 false B 3.729,2.25 3.885,2.448 0.156,0.198 10 false A 5.469,3.969 5.927,4.167 0.458,0.198 10 false A64 5.458,4.125 6.99,4.552 1.531,0.427 10 false Skid Control ECU (Brake Actuator Assembly) 0.354,4.906 1.823,5.469 1.469,0.563 10 false Rear Combination Light Lens and Body LH 1.958,4.917 3.427,5.479 1.469,0.563 10 false Rear Combination Light Lens and Body RH 2.156,4.708 2.615,4.906 0.458,0.198 10 false M19 0.51,4.677 0.917,4.885 0.406,0.208 10 false N13 3.99,3.792 4.302,3.99 0.313,0.198 10 false U1 0.406,3.885 0.563,4.083 0.156,0.198 10 false B 0.427,4.219 0.583,4.417 0.156,0.198 10 false E 2.063,3.896 2.219,4.094 0.156,0.198 10 false B 2.083,4.219 2.25,4.438 0.167,0.219 10 false E 3.49,3.885 3.646,4.083 0.156,0.198 10 false B 3.49,4.198 3.646,4.396 0.156,0.198 10 false E 0.354,3.656 0.604,3.844 0.25,0.188 10 false 1 0.375,4.406 0.531,4.604 0.156,0.198 10 false 4 1.844,3.688 2,3.885 0.156,0.198 10 false 1 1.844,4.427 2,4.625 0.156,0.198 10 false 4 3.719,3.656 3.875,3.854 0.156,0.198 10 false 2 3.729,4.417 3.906,4.625 0.177,0.208 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that all the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed ON
Brake pedal released OFF



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (STP TERMINAL)

NG

2.CHECK TERMINAL VOLTAGE (STP TERMINAL)
a.
C199357
1.635,0.083 2.01,0.344 0.375,0.26 0.51,0.438 1.25,0.844 false 1.698,0.125 2.156,0.323 0.458,0.198 10 false A64 0.198,0.354 0.656,0.552 0.458,0.198 10 false STP 0,0 0.313,0.156 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A64 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A64-2 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 8 to 14 V
Stop light switch OFF (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT CIRCUIT)

3.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Reconnect the A64 skid control ECU (brake actuator assembly) connector.



Chassis > ABS/VSC/TRAC > Clear DTCs
50002 105
d.

Start the engine.


e.

Depress the brake pedal several times to test the stop light circuit.



Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105
HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Proceed to
DTC C1425 is not output
DTC C1425 is output



DTC C1425 is not output

DTC C1425 is output