Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM30B0U _54 Brake _010842 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0058073 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1427  Motor Malfunction  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C1427 Motor Malfunction Actuator pump motor does not operate properly.
·

ABS NO. 1 fuse

·

Brake actuator assembly (Ground circuit)

·

Brake actuator assembly (Motor circuit)



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (MOTOR RELAY)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.


e.

According to the display on the Techstream, perform the Active Test.


Chassis > ABS/VSC/TRAC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Motor Relay Motor relay Relay ON / OFF Operating sound of motor can be heard.
Vehicle condition: Vehicle stopped
Chassis > ABS/VSC/TRAC > Active Test
Tester Display
Motor Relay
50004 105 2
f.

Check the operating sound of the motor relay when operating it with the Techstream.


Result:
Proceed to
The operating sound is not heard
The operating sound is heard



The operating sound is not heard

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

The operating sound is heard

3.RECONFIRM DTC
2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A64 skid control ECU (brake actuator assembly) connector.


d.
C199357
1.635,0.115 2.01,0.365 0.375,0.25 0.604,1.74 1.063,1.302 false 1.698,0.177 2.156,0.375 0.458,0.198 10 false A64 0.417,1.781 0.854,1.979 0.438,0.198 10 false GND2 0,0 0.313,0.156 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-13 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)

3.RECONFIRM DTC
HINT:

This code is detected when a problem is identified in the brake actuator assembly.

The motor relay is in the brake actuator assembly.

Therefore, motor relay unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the brake actuator assembly.


a.

Turn the ignition switch off.


b.

Reconnect the A64 skid control ECU (brake actuator assembly) connector.



Chassis > ABS/VSC/TRAC > Clear DTCs
50002 105
d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.



Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105
HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (no trouble codes are output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly. Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.



Result:
Proceed to
DTC C1427 is not output
DTC C1427 is output



DTC C1427 is not output

DTC C1427 is output