Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM30B0U _54 Brake _010842 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0058073 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1437  Lost Communication with ECM  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the ECM via the CAN communication system.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1437 Lost Communication with ECM When the IG1 terminal voltage is 10 V or more and the vehicle speed is 15 km/h (9 mph) or more, data cannot be sent to the ECM for 2 seconds or more.
·

CAN communication system (skid control ECU to ECM)

·

Skid control ECU (brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the Techstream, check for any momentary interruption in the wire harness and connector corresponding to the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


Chassis > ABS/VSC/TRAC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
EFI Communication Open EFI communication open detection Normal or Error Normal Error: Momentary interruption
Chassis > ABS/VSC/TRAC > Data List
Tester Display
EFI Communication Open
50003 105 204
HINT:

Perform the above inspection before removing the sensor and connector.


OK:

There are no momentary interruptions.


Result:
Proceed to
OK
NG



OK

2.RECONFIRM DTC

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ECM)
2.RECONFIRM DTC
a.

Turn the ignition switch off.



Chassis > ABS/VSC/TRAC > Clear DTCs
50002 105
c.

Start the engine.


d.

Drive the vehicle at a speed of 15 km/h (9 mph) or more for 10 seconds or more.


e.

Check that no CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105
Result:
Proceed to
DTC C1437 is not output
DTC C1437 is output
CAN communication system DTC is output



DTC C1437 is not output

DTC C1437 is output

CAN communication system DTC is output

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ECM)
a.

Turn the ignition switch off.


b.

Repair or replace the harness or connector.


c.

Check for any momentary interruption between the skid control ECU (brake actuator assembly) and the ECM.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


d.

Check that there is no momentary interruption.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Turn the ignition switch off.



Chassis > ABS/VSC/TRAC > Clear DTCs
50002 105
c.

Start the engine.


d.

Drive the vehicle at a speed of 15 km/h (9 mph) or more for 10 seconds or more.


e.

Check that no CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105
Result:
Proceed to
DTC is not output
DTC is output
CAN communication system DTC is output



DTC is not output

END

DTC is output

CAN communication system DTC is output