Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM30B0U _58 Vehicle Interior _010074 SUPPLEMENTAL RESTRAINT SYSTEMS _0058017 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1650/32  Occupant Classification System Malfunction  


DESCRIPTION

The occupant classification system circuit consists of the airbag sensor assembly and occupant detection ECU.

If the airbag sensor assembly receives signals from the occupant detection ECU, it determines whether the instrument panel passenger airbag, front seat airbag RH and front seat outer belt assembly should be operated.

DTC B1650/32 is stored when a malfunction is detected in the occupant classification system circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1650/32 Occupant Classification System Malfunction
One of the following conditions is met:
·

An occupant classification system malfunction.

·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the occupant classification system circuit for 2 seconds.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front seat wire RH

·

Occupant detection ECU

·

Airbag sensor assembly



WIRING DIAGRAM

C238367
0.594,3.094 2.292,3.458 1.698,0.365 10 false Occupant Detection ECU 0.594,2.906 1.135,3.375 0.542,0.469 10 false d16 3.438,0.906 3.865,1.333 0.427,0.427 10 false Md1 3.521,0.708 3.792,1.031 0.271,0.323 10 false 1 3.521,1.885 3.781,2.323 0.26,0.438 10 false 5 3.427,2.083 3.844,2.479 0.417,0.396 10 false Md1 5.146,0.813 5.552,1.292 0.406,0.479 10 false 9 5.156,1.979 5.552,2.49 0.396,0.51 10 false 17 5.354,2.906 5.771,3.26 0.417,0.354 10 false M25 5.354,3.094 6.927,3.448 1.573,0.354 10 false Airbag Sensor Assembly 5.406,0.906 5.854,1.323 0.448,0.417 10 false FSR+ 5.385,2.083 5.802,2.479 0.417,0.396 10 false FSR- 1.854,0.781 2.313,1.354 0.458,0.573 10 false 7 1.865,1.958 2.219,2.281 0.354,0.323 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to ON, and wait for at least 10 seconds.


b.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59

c.

Check for DTCs of the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59

Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

2.CHECK DTC

DTC is output

2.CHECK DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1650/32 is not output
DTC B1650/32 is output


HINT:

Codes other than DTC B1650/32 may be output at this time, but they are not related to this check.




DTC B1650/32 is not output

DTC B1650/32 is output

3.CHECK CONNECTION OF CONNECTORS
3.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and occupant detection ECU.


Result:
Proceed to
Connectors are properly connected
Connectors are not properly connected



Connectors are properly connected

4.CHECK CONNECTORS

Connectors are not properly connected

CONNECT CONNECTORS PROPERLY

4.CHECK CONNECTORS
a.
C253249
0.625,1.302 0.938,1.458 0.313,0.156 10 false *1 2.448,1.729 2.76,1.885 0.313,0.156 10 false *2
*1 Occupant Detection ECU
*2 Airbag Sensor Assembly


Disconnect the connectors from the airbag sensor assembly and occupant detection ECU.


b.

Check that the connectors (on the airbag sensor assembly side and occupant detection ECU side) are not damaged.


Result:
Proceed to
Connectors are not deformed or damaged
Connectors are deformed or damaged



Connectors are not deformed or damaged

5.CHECK OCCUPANT DETECTION ECU CIRCUIT

Connectors are deformed or damaged

REPLACE HARNESS AND CONNECTOR

5.CHECK OCCUPANT DETECTION ECU CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C253250
2.698,0.542 3.083,0.76 0.385,0.219 4.74,0.552 5.125,0.771 0.385,0.219 6.594,0.875 6.74,0.875 false 6.208,0.802 6.469,0.438 false 6.219,0.938 6.438,1.313 false 0.521,1.01 0.833,1.167 0.313,0.156 10 false *1 1.958,1.271 2.271,1.427 0.313,0.156 10 false *2 3.646,0.229 3.958,0.385 0.313,0.156 10 false *3 5.844,0.24 6.156,0.396 0.313,0.156 10 false *4 6.792,0.792 7.104,0.948 0.313,0.156 10 false *5 1.792,0.625 2.104,0.781 0.313,0.156 10 false A 3.167,0.094 3.479,0.25 0.313,0.156 10 false *a 5.427,0.063 5.74,0.219 0.313,0.156 10 false *b 1.5,0.823 1.813,0.979 0.313,0.156 10 false B 1.229,0.823 1.542,0.979 0.313,0.156 10 false C 1.115,0.823 1.427,0.979 0.313,0.156 10 false D 0.844,0.833 1.156,0.99 0.313,0.156 10 false E 0.583,0.656 0.896,0.813 0.313,0.156 10 false F 2.76,0.563 3.073,0.719 0.313,0.156 10 false d16 4.792,0.573 5.104,0.729 0.313,0.156 10 false M25 6.521,0.354 6.99,0.51 0.469,0.156 10 false FSR+ 6.5,1.25 6.969,1.406 0.469,0.156 10 false FSR-
*1 Occupant Detection ECU *2 Airbag Sensor Assembly
*3 Connector E *4 Connector B
*5 Service Wire - -
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
d16-7 - Body ground Ignition switch ON Below 1 V
d16-4 - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 9 (FSR+) and 17 (FSR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d16-7 - d16-4 Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d16-7 - d16-4 Always 1 MΩ or higher
d16-7 - Body ground Always 1 MΩ or higher
d16-4 - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

6.CHECK FLOOR WIRE
6.CHECK FLOOR WIRE
a.

Disconnect the front seat inner belt assembly RH connector from the floor wire.

C282012
5.073,0.656 5.448,0.875 0.375,0.219 2.938,0.646 3.313,0.865 0.375,0.219 6.573,0.573 6.26,0.885 true 6.542,1.354 6.281,1 true 6.844,0.833 6.698,0.896 true 1.833,0.656 1.99,0.854 0.156,0.198 10 false A 1.542,0.844 1.698,1.042 0.156,0.198 10 false B 1.26,0.844 1.417,1.042 0.156,0.198 10 false C 1.104,0.844 1.26,1.042 0.156,0.198 10 false D 0.823,0.844 0.979,1.042 0.156,0.198 10 false E 0.542,0.635 0.698,0.833 0.156,0.198 10 false F 0.406,0.99 0.688,1.354 0.281,0.365 10 false *1 1.906,1.26 2.177,1.479 0.271,0.219 10 false *2 0.938,0.49 1.208,0.708 0.271,0.219 10 false *3 1.375,0.49 1.646,0.708 0.271,0.219 10 false *4 3.833,0.115 4.104,0.333 0.271,0.219 10 false *a 4.521,0.708 4.792,0.927 0.271,0.219 10 false *5 3,0.667 3.302,0.958 0.302,0.292 10 false Md1 5.146,0.677 5.448,0.969 0.302,0.292 10 false M25 6.854,0.729 7.094,1.042 0.24,0.313 10 false *7 6.396,0.281 6.698,0.573 0.302,0.292 10 false *6 5.958,0.177 6.26,0.469 0.302,0.292 10 false *b 6.615,0.5 7.01,0.698 0.396,0.198 10 false FSR+ 6.594,1.292 6.99,1.49 0.396,0.198 10 false FSR-
*1 Occupant Detection ECU *2 Airbag Sensor Assembly
*3 Front Seat Wire RH *4 Floor Wire
*5 Connector C - Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Front Seat Wire RH)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Md1-1 - Body ground Ignition switch ON Below 1 V
Md1-5 - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 9 (FSR+) and 17 (FSR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Md1-1 - Md1-5 Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Md1-1 - Md1-5 Always 1 MΩ or higher
Md1-1 - Body ground Always 1 MΩ or higher
Md1-5 - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE FLOOR WIRE