Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM30B0U _58 Vehicle Interior _010074 SUPPLEMENTAL RESTRAINT SYSTEMS _0058017 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1653/35  Seat Position Airbag Sensor Circuit Malfunction  


DESCRIPTION

The seat position airbag sensor circuit consists of the airbag sensor assembly and seat position airbag sensor.

DTC B1653/35 is stored when a malfunction is detected in the seat position airbag sensor circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1653/35 Seat Position Airbag Sensor Circuit Malfunction
One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the seat position airbag sensor circuit for 2 seconds.

·

A seat position airbag sensor malfunction.

·

An airbag sensor assembly malfunction


·

No. 2 floor wire

·

Front seat inner belt assembly LH

·

Seat position airbag sensor

·

Airbag sensor assembly



WIRING DIAGRAM

C253789
0.344,3.833 0.646,4 0.302,0.167 10 false N14 0.354,4 2.573,4.156 2.219,0.156 10 false Front Seat Inner Belt Assembly LH 0.563,3.177 2.406,3.333 1.844,0.156 10 false Seat Position Airbag Sensor 2.958,2.844 3.063,2.99 0.104,0.146 10 false 3 2.167,1.354 2.292,1.521 0.125,0.167 10 false 2 2.969,1.354 3.094,1.5 0.125,0.146 10 false 4 2.208,2.833 2.333,2.979 0.125,0.146 10 false 1 5.396,1.156 5.594,1.313 0.198,0.156 10 false 16 5.719,1.208 6.135,1.375 0.417,0.167 10 false LSP+ 5.406,2.833 5.615,3.021 0.208,0.188 10 false 24 5.729,2.698 6.104,2.854 0.375,0.156 10 false LSP- 2.49,1.125 2.906,1.292 0.417,0.167 10 false LSP+ 2.51,2.604 2.885,2.76 0.375,0.156 10 false LSP- 5.469,3.771 5.781,3.938 0.313,0.167 10 false N21 5.469,3.938 7.052,4.167 1.583,0.229 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and seat position airbag sensor.


Result:
Proceed to
Connectors are properly connected
Connectors are not properly connected



Connectors are properly connected

2.CHECK CONNECTORS

Connectors are not properly connected

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.
C215011
0.677,1.719 0.99,1.875 0.313,0.156 10 false *1 2.5,1.542 2.813,1.698 0.313,0.156 10 false *2
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly


Disconnect the connectors from the airbag sensor assembly and seat position airbag sensor.


b.

Check that the connectors (on the airbag sensor assembly side and seat position airbag sensor side) are not damaged.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


Result:
Proceed to
Connectors are not deformed or damaged
Connectors are deformed or damaged



Connectors are not deformed or damaged

3.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT

Connectors are deformed or damaged

REPLACE HARNESS AND CONNECTOR OR FRONT SEAT INNER BELT ASSEMBLY LH

3.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C253252
4.125,0.51 4.521,0.729 0.396,0.219 4.802,0.896 5.042,0.896 false 5,0.531 5.271,0.833 false 4.979,1.302 5.271,0.99 false 0.385,1.302 0.698,1.458 0.313,0.156 10 false *1 1.865,1.167 2.177,1.323 0.313,0.156 10 false *2 3.844,0.563 4.156,0.719 0.313,0.156 10 false *3 6.052,0.375 6.365,0.531 0.313,0.156 10 false *4 4.604,0.823 4.917,0.979 0.313,0.156 10 false *5 1.729,0.917 1.885,1.073 0.156,0.156 10 false A 3.292,0.302 3.604,0.458 0.313,0.156 10 false *a 5.479,0.229 5.792,0.385 0.313,0.156 10 false *b 1.448,1.146 1.604,1.302 0.156,0.156 10 false B 1.167,1.146 1.323,1.302 0.156,0.156 10 false C 1.063,1.146 1.219,1.302 0.156,0.156 10 false D 0.781,1.146 0.938,1.302 0.156,0.156 10 false E 0.521,0.938 0.677,1.094 0.156,0.156 10 false F 4.74,1.344 5.125,1.521 0.385,0.177 10 false LSP- 4.635,0.406 5.021,0.583 0.385,0.177 10 false LSP+ 4.188,0.531 4.573,0.708 0.385,0.177 10 false N21
*1 Seat Position Airbag Sensor *2 Airbag Sensor Assembly
*3 Connector E *4 Connector B
*5 Service Wire - -
*a Front view of wire harness connector
(to Seat Position Airbag Sensor)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
1 - Body ground Ignition switch ON Below 1 V
2 - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 24 (LSP-) and 16 (LSP+) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 1 MΩ or higher
1 - Body ground Always 1 MΩ or higher
2 - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK SEAT POSITION AIRBAG SENSOR

NG

7.CHECK NO. 2 FLOOR WIRE
4.CHECK SEAT POSITION AIRBAG SENSOR
a.
C253253
0.781,1.558 0.951,1.728 0.17,0.17 10 *1 2.362,1.409 2.532,1.579 0.17,0.17 10 *2
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and seat position airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1653/35 is not output
DTC B1653/35 is output


HINT:

Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.




DTC B1653/35 is not output

DTC B1653/35 is output

5.CHECK SEAT POSITION AIRBAG SENSOR
5.CHECK SEAT POSITION AIRBAG SENSOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the seat position airbag sensor.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL

HINT:

Perform the inspection using parts from a normal vehicle if possible.



Result:
Proceed to
NEXT



NEXT

6.CHECK AIRBAG SENSOR ASSEMBLY
6.CHECK AIRBAG SENSOR ASSEMBLY
a.
C253253
0.781,1.558 0.951,1.728 0.17,0.17 10 *1 2.362,1.409 2.532,1.579 0.17,0.17 10 *2
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1653/35 is not output
DTC B1653/35 is output


HINT:

Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.




DTC B1653/35 is not output

END (SEAT POSITION AIRBAG SENSOR WAS DEFECTIVE)

DTC B1653/35 is output

7.CHECK NO. 2 FLOOR WIRE
a.

Disconnect the No. 2 floor wire connector from the front seat inner belt assembly LH.

C253254
2.583,0.656 2.969,0.885 0.385,0.229 4.115,0.469 4.5,0.698 0.385,0.229 5.146,0.75 5.438,0.979 false 5.156,1.385 5.438,1.104 false 4.99,1.042 5.198,1.042 false 3.073,1.385 3.333,1.125 false 3.802,1.365 3.573,1.125 false 0.365,1.292 0.677,1.448 0.313,0.156 10 false *1 1.958,1.135 2.271,1.292 0.313,0.156 10 false *2 0.906,0.771 1.219,0.927 0.313,0.156 10 false *3 1.323,0.76 1.635,0.917 0.313,0.156 10 false *4 3.365,0.344 3.677,0.5 0.313,0.156 10 false *5 5.635,0.396 5.906,0.604 0.271,0.208 10 false *6 2.844,0.125 3.156,0.281 0.313,0.156 10 false *a 5.052,0.115 5.365,0.271 0.313,0.156 10 false *b 1.771,0.896 2.083,1.052 0.313,0.156 10 false A 1.51,1.146 1.823,1.302 0.313,0.156 10 false B 1.229,1.146 1.542,1.302 0.313,0.156 10 false C 1.073,1.146 1.385,1.302 0.313,0.156 10 false D 0.781,1.146 1.094,1.302 0.313,0.156 10 false E 0.51,0.906 0.823,1.063 0.313,0.156 10 false F 2.667,0.688 2.979,0.844 0.313,0.156 10 false N14 4.167,0.49 4.479,0.646 0.313,0.156 10 false N21 4.802,0.969 5.073,1.177 0.271,0.208 10 false *7 4.729,0.646 5.104,0.813 0.375,0.167 10 false LSP+ 4.781,1.313 5.156,1.479 0.375,0.167 10 false LSP- 2.844,1.427 3.219,1.594 0.375,0.167 10 false LSP- 3.708,1.406 4.083,1.573 0.375,0.167 10 false LSP+
*1 Seat Position Airbag Sensor *2 Airbag Sensor Assembly
*3 Front Seat Inner Belt Assembly LH *4 No. 2 Floor Wire
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N14-4 (LSP+) - Body ground Ignition switch ON Below 1 V
N14-3 (LSP-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 24 (LSP-) and 16 (LSP+) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N14-4 (LSP+) - N14-3 (LSP-) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N14-4 (LSP+) - N14-3 (LSP-) Always 1 MΩ or higher
N14-4 (LSP+) - Body ground Always 1 MΩ or higher
N14-3 (LSP-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

NG

REPLACE NO. 2 FLOOR WIRE