The front passenger side squib 2nd step circuit consists of the airbag sensor assembly and instrument panel passenger airbag.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front passenger side squib 2nd step circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1815/54 | Short in Front Passenger Side Squib 2nd Step Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects a line short circuit signal 5 times in the front passenger side squib 2nd step circuit during the primary check. ·
A front passenger side squib 2nd step malfunction. ·
An airbag sensor assembly malfunction. |
·
Instrument panel wire ·
No. 2 instrument panel wire ·
Instrument panel passenger airbag assembly (Front passenger side squib 2nd step) ·
Airbag sensor assembly |
| B1816/54 | Open in Front Passenger Side Squib 2nd Step Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects an open circuit signal in the front passenger side squib 2nd step circuit for 2 seconds. ·
A front passenger side squib 2nd step malfunction. ·
An airbag sensor assembly malfunction. |
·
Instrument panel wire ·
No. 2 instrument panel wire ·
Instrument panel passenger airbag assembly (Front passenger side squib 2nd step) ·
Airbag sensor assembly |
| B1817/54 | Short to GND in Front Passenger Side Squib 2nd Step Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects a short circuit to ground signal in the front passenger side squib 2nd step circuit for 0.5 seconds. ·
A front passenger side squib 2nd step malfunction. ·
An airbag sensor assembly malfunction. |
·
Instrument panel wire ·
No. 2 instrument panel wire ·
Instrument panel passenger airbag assembly (Front passenger side squib 2nd step) ·
Airbag sensor assembly |
| B1818/54 | Short to B+ in Front Passenger Side Squib 2nd Step Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects a short circuit to B+ signal in the front passenger side squib 2nd step circuit for 0.5 seconds. ·
A front passenger side squib 2nd step malfunction. ·
An airbag sensor assembly malfunction. |
·
Instrument panel wire ·
No. 2 instrument panel wire ·
Instrument panel passenger airbag assembly (Front passenger side squib 2nd step) ·
Airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After replacing the airbag sensor assembly, refer to initialization.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
To perform the simulation method, enter check mode (signal check) with the Techstream (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).
| *1 | Front Passenger Side Squib 2nd Step |
| *2 | Airbag Sensor Assembly |
| *3 | Connector E |
| *4 | SST |
| *a | Front view of wire harness connector
(to Front Passenger Side Squib 2nd Step) |
| *b | Color: Black |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the instrument panel passenger airbag.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (black connector).
Never connect the tester to the curtain shield airbag assembly RH (curtain shield squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting SST.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1815/54, B1816/54, B1817/54 or B1818/54 is not output |
| DTC B1815/54, B1816/54, B1817/54 or B1818/54 is output |
Codes other than DTC B1815/54, B1816/54, B1817/54 and B1818/54 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector E.
DTC B1815/54, B1816/54, B1817/54 or B1818/54 is not output
DTC B1815/54, B1816/54, B1817/54 or B1818/54 is output
Disconnect the connectors from the airbag sensor assembly.
| *1 | Front Passenger Side Squib 2nd Step |
| *2 | Airbag Sensor Assembly |
Check that the connectors (on the airbag sensor assembly side and instrument panel passenger airbag side) are not damaged.
The lock button is not disengaged, and the claw of the lock is not damaged or deformed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Passenger Side Squib 2nd Step |
| *2 | Airbag Sensor Assembly |
| *3 | Connector E |
| *a | Front view of wire harness connector
(to Front Passenger Side Squib 2nd Step) |
| *b | Color: Black |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| b2-2 (P2+) - Body ground | Ignition switch ON | Below 1 V |
| b2-1 (P2-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b2-2 (P2+) - b2-1 (P2-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b2-2 (P2+) -b2-1 (P2-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to its original condition.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b2-2 (P2+) - Body ground | Always | 1 MΩ or higher |
| b2-1 (P2-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Passenger Side Squib 2nd Step |
| *2 | Airbag Sensor Assembly |
Connect the connectors to the instrument panel passenger airbag and airbag sensor assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1815/54, B1816/54, B1817/54 or B1818/54 is not output |
| DTC B1815/54, B1816/54, B1817/54 or B1818/54 is output |
Codes other than DTC B1815/54, B1816/54, B1817/54 and B1818/54 may be output at this time, but they are not related to this check.
DTC B1815/54, B1816/54, B1817/54 or B1818/54 is not output
DTC B1815/54, B1816/54, B1817/54 or B1818/54 is output
| *1 | Front Passenger Side Squib 2nd Step |
| *2 | No. 2 Instrument Panel Wire |
| *3 | Instrument Panel Wire |
| *4 | Airbag Sensor Assembly |
| *5 | Connector C |
| *a | Front view of wire harness connector
(to No. 2 Instrument Panel Wire) |
Disconnect the instrument panel wire connector from the No. 2 instrument panel wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Gb1-3 (P2+) - Body ground | Ignition switch ON | Below 1 V |
| Gb1-4 (P2-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Gb1-3 (P2+) - Gb1-4 (P2-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Gb1-3 (P2+) - Gb1-4 (P2-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to its original condition.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Gb1-3 (P2+) - Body ground | Always | 1 MΩ or higher |
| Gb1-4 (P2-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG