Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM30B0U _58 Vehicle Interior _010074 SUPPLEMENTAL RESTRAINT SYSTEMS _0058017 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B181A/7A  Short in Passenger Side Airbag Variable Vent Hole Squib Circuit  B181B/7A  Open in Passenger Side Airbag Variable Vent Hole Squib Circuit  B181C/7A  Short to GND in Passenger Side Airbag Variable Vent Hole Squib Circuit  B181D/7A  Short to B+ in Passenger Side Airbag Variable Vent Hole Squib Circuit  


DESCRIPTION

The variable vent hole squib circuit consists of the airbag sensor assembly and instrument panel passenger airbag assembly. The circuit instructs the SRS to deploy when the deployment conditions are met.

These DTCs are stored when a malfunction is detected in the variable vent hole squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B181A/7A Short in Passenger Side Airbag Variable Vent Hole Squib Circuit
One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal 5 times in the variable vent hole squib circuit during the primary check.

·

A variable vent hole squib malfunction.

·

An airbag sensor assembly malfunction.


·

No. 2 instrument panel wire

·

Instrument panel wire

·

Instrument panel passenger airbag assembly (Variable vent hole squib)

·

Airbag sensor assembly


B181B/7A Open in Passenger Side Airbag Variable Vent Hole Squib Circuit
One of the following conditions is met:
·

The airbag sensor assembly detects an open circuit signal in the variable vent hole squib circuit for 2 seconds.

·

A variable vent hole squib malfunction.

·

An airbag sensor assembly malfunction.


·

No. 2 instrument panel wire

·

Instrument panel wire

·

Instrument panel passenger airbag assembly (Variable vent hole squib)

·

Airbag sensor assembly


B181C/7A Short to GND in Passenger Side Airbag Variable Vent Hole Squib Circuit
One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to ground signal in the variable vent hole squib circuit for 0.5 seconds.

·

A variable vent hole squib malfunction.

·

An airbag sensor assembly malfunction.


·

No. 2 instrument panel wire

·

Instrument panel wire

·

Instrument panel passenger airbag assembly (Variable vent hole squib)

·

Airbag sensor assembly


B181D/7A Short to B+ in Passenger Side Airbag Variable Vent Hole Squib Circuit
One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to B+ signal in the variable vent hole squib circuit for 0.5 seconds.

·

A variable vent hole squib malfunction.

·

An airbag sensor assembly malfunction.


·

No. 2 instrument panel wire

·

Instrument panel wire

·

Instrument panel passenger airbag assembly (Variable vent hole squib)

·

Airbag sensor assembly



WIRING DIAGRAM

C253311
1.125,0.927 1.583,1.115 0.458,0.188 10 false VHP+ 1.167,2.135 1.583,2.313 0.417,0.177 10 false VHP- 5.531,0.927 5.75,1.073 0.219,0.146 10 false 19 5.573,2.135 5.781,2.313 0.208,0.177 10 false 20 5.479,2.969 5.76,3.115 0.281,0.146 10 false G92 5.51,3.135 7.063,3.333 1.552,0.198 10 false Airbag Sensor Assembly 3.375,0.781 3.479,0.948 0.104,0.167 10 false 1 1.615,2.115 1.719,2.281 0.104,0.167 10 false 1 3.375,2 3.479,2.167 0.104,0.167 10 false 2 1.604,0.917 1.708,1.083 0.104,0.167 10 false 2 3.271,1.021 3.552,1.188 0.281,0.167 10 false Gb3 3.281,2.219 3.563,2.385 0.281,0.167 10 false Gb3 0.135,3.01 0.323,3.167 0.188,0.156 10 false b3 0.115,3.167 2.927,3.521 2.813,0.354 10 false Instrument Panel Passenger Airbag Assembly (Variable Vent Hole Squib) 5.813,2.229 6.229,2.406 0.417,0.177 10 false VHP- 5.823,1.021 6.281,1.208 0.458,0.188 10 false VHP+ 3.229,1.229 3.688,1.417 0.458,0.188 10 false VHP+ 3.271,2.427 3.688,2.604 0.417,0.177 10 false VHP-

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:

To perform the simulation method, enter check mode (signal check) with the Techstream (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).


PROCEDURE

1.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (VARIABLE VENT HOLE SQUIB)
a.
C252988
0.385,2.135 0.813,2.344 0.427,0.208 2.031,2.656 2.26,2.729 false 1.5,2.76 1.24,2.865 false 0.458,0.458 0.771,0.615 0.313,0.156 10 false *1 2.313,1.281 2.625,1.438 0.313,0.156 10 false *2 2.417,2.271 2.729,2.427 0.313,0.156 10 false *3 0.25,1.635 0.563,1.792 0.313,0.156 10 false *a 1.021,2.802 1.333,2.958 0.313,0.156 10 false *b 1.917,0.656 2.229,0.813 0.313,0.156 10 false A 1.427,0.906 1.74,1.063 0.313,0.156 10 false C 1.26,0.896 1.573,1.052 0.313,0.156 10 false D 0.906,0.906 1.219,1.063 0.313,0.156 10 false E 0.698,0.906 1.01,1.063 0.313,0.156 10 false F 0.51,2.156 0.792,2.385 0.281,0.229 10 false b3 2.302,2.698 2.698,2.917 0.396,0.219 10 false *4
*1 Variable Vent Hole Squib
*2 Airbag Sensor Assembly
*3 Connector E
*4 SST
*a Front view of wire harness connector
(to Variable Vent Hole Squib)
*b Color: Green


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the instrument panel passenger airbag assembly.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (green connector).

CAUTION:

Never connect the tester to the instrument panel passenger airbag assembly (variable vent hole squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is not output
DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is output


HINT:

Codes other than DTC B181A/7A, B181B/7A, B181C/7A and B181D/7A may be output at this time, but they are not related to this check.




DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is not output

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is output

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector E.


d.

Disconnect the connectors from the airbag sensor assembly.


e.
C208248
0.385,0.813 0.698,0.969 0.313,0.156 10 false *1 2.406,1.708 2.719,1.865 0.313,0.156 10 false *2 2.177,1.021 2.49,1.177 0.313,0.156 10 false A 1.74,1.354 2.052,1.51 0.313,0.156 10 false B 1.354,1.354 1.667,1.51 0.313,0.156 10 false C 1.208,1.354 1.521,1.51 0.313,0.156 10 false D 0.833,1.354 1.146,1.51 0.313,0.156 10 false E 0.563,1.354 0.875,1.51 0.313,0.156 10 false F
*1 Variable Vent Hole Squib
*2 Airbag Sensor Assembly


Check that the connectors (on the airbag sensor assembly side and instrument panel passenger airbag assembly side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK VARIABLE VENT HOLE SQUIB CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

3.CHECK VARIABLE VENT HOLE SQUIB CIRCUIT
a.
C252989
0.635,1.875 1.021,2.135 0.385,0.26 1.76,2.156 2.094,2.365 true 1.635,2.167 1.292,2.344 true 1.521,2.76 1.292,2.875 true 0.51,0.479 0.823,0.635 0.313,0.156 10 false *1 2.5,1.313 2.813,1.469 0.313,0.156 10 false *2 1.615,1.604 1.927,1.76 0.313,0.156 10 false *3 0.74,1.438 1.052,1.594 0.313,0.156 10 false *a 1.135,2.833 1.448,2.99 0.313,0.156 10 false *b 2.24,0.667 2.552,0.823 0.313,0.156 10 false A 1.854,0.948 2.031,1.146 0.177,0.198 10 false B 1.469,0.938 1.646,1.135 0.177,0.198 10 false C 1.344,0.938 1.521,1.135 0.177,0.198 10 false D 0.979,0.927 1.156,1.125 0.177,0.198 10 false E 0.75,0.938 0.927,1.135 0.177,0.198 10 false F 2.104,2.417 2.583,2.635 0.479,0.219 10 false VHP+ 1.031,2.385 1.417,2.552 0.385,0.167 10 false VHP- 0.76,1.927 1.24,2.146 0.479,0.219 10 false b3
*1 Variable Vent Hole Squib
*2 Airbag Sensor Assembly
*3 Connector E
*a Front view of wire harness connector
(to Variable Vent Hole Squib)
*b Color: Green


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
b3-2 (VHP+) - Body ground Ignition switch ON Below 1 V
b3-1 (VHP-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b3-2 (VHP+) - b3-1 (VHP-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b3-2 (VHP+) - b3-1 (VHP-) Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b3-2 (VHP+) - Body ground Always 1 MΩ or higher
b3-1 (VHP-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK AIRBAG SENSOR ASSEMBLY

NG

5.CHECK VARIABLE VENT HOLE SQUIB CIRCUIT
4.CHECK AIRBAG SENSOR ASSEMBLY
a.
C147154
0.49,0.677 0.802,0.833 0.313,0.156 10 false *1 2.083,1.438 2.396,1.594 0.313,0.156 10 false *2 1.323,1.125 1.635,1.281 0.313,0.156 10 false C 1.219,1.125 1.531,1.281 0.313,0.156 10 false D 0.854,1.125 1.167,1.281 0.313,0.156 10 false E 0.74,1.125 1.052,1.281 0.313,0.156 10 false F 1.865,0.854 2.177,1.01 0.313,0.156 10 false A
*1 Variable Vent Hole Squib
*2 Airbag Sensor Assembly


Restore the released activation prevention mechanism of connector B to its original condition.


b.

Connect the connectors to the instrument panel passenger airbag assembly and airbag sensor assembly.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is output
DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is not output


HINT:

Codes other than DTC B181A/7A, B181B/7A, B181C/7A and B181D/7A may be output at this time, but they are not related to this check.




DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is output

DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is not output

5.CHECK VARIABLE VENT HOLE SQUIB CIRCUIT
a.

Restore the released activation prevention mechanism of connector B to its original condition.


b.
E272056
0.302,2.115 0.688,2.344 0.385,0.229 1.219,2.917 1.552,2.635 false 2.229,2.948 1.865,2.604 false 0.552,0.417 0.865,0.573 0.313,0.156 10 false *1 1.104,0.406 1.417,0.563 0.313,0.156 10 false *2 1.688,0.406 2,0.563 0.313,0.156 10 false *3 2.396,1.188 2.708,1.344 0.313,0.156 10 false *4 2.25,1.99 2.563,2.146 0.313,0.156 10 false *5 1.604,1.667 1.917,1.823 0.313,0.156 10 false *a 0.365,2.125 0.677,2.281 0.313,0.156 10 false Gb3 1,2.969 1.438,3.177 0.438,0.208 10 false VHP+ 2.104,2.99 2.542,3.198 0.438,0.208 10 false VHP- 2.271,0.583 2.583,0.74 0.313,0.156 10 false A 1.917,0.833 2.229,0.99 0.313,0.156 10 false B 1.542,0.833 1.854,0.99 0.313,0.156 10 false C 1.313,0.833 1.625,0.99 0.313,0.156 10 false D 0.938,0.833 1.25,0.99 0.313,0.156 10 false E 0.729,0.833 1.042,0.99 0.313,0.156 10 false F
*1 Variable Vent Hole Squib
*2 No. 2 Instrument Panel Wire
*3 Instrument Panel Wire
*4 Airbag Sensor Assembly
*5 Connector E
*a Front view of wire harness connector
(to No. 2 Instrument Panel Wire)


Disconnect the instrument panel wire connector from the No. 2 instrument panel wire.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Gb3-1 (VHP+) - Body ground Ignition switch ON Below 1 V
Gb3-2 (VHP-) - Body ground Ignition switch ON Below 1 V



f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Gb3-1 (VHP+) - Gb3-2 (VHP-) Always Below 1 Ω



i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Gb3-1 (VHP+) - Gb3-2 (VHP-) Always 1 MΩ or higher



k.

Restore the released activation prevention mechanism of connector B to its original condition.


l.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Gb3-1 (VHP+) - Body ground Always 1 MΩ or higher
Gb3-2 (VHP-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 INSTRUMENT PANEL WIRE

NG

REPLACE NO. 2 INSTRUMENT PANEL WIRE