Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR
RM30B0U _54 Brake _010842 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0058119 BRAKE ACTUATOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR  INSTALLATION  


PROCEDURE

Hide 1.INSTALL BRAKE ACTUATOR WITH BRACKET

NOTICE:

When installing a new brake actuator, do not remove the hole plug before connecting the brake tube. New actuators are filled with brake fluid.


a.
C191857
0.857,1.852 0.971,2.003 0.114,0.151 10 A 1.775,1.988 1.889,2.139 0.114,0.151 10 B 2.143,1.898 2.266,2.049 0.123,0.151 10 C

Install the actuator with bracket with the 3 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Tighten the 3 nuts uniformly in alphabetical order.

·

Be careful not to damage the brake tubes.

·

Do not drop the actuator. If dropped, replace it.




b.

Connect the brake tube clamp to the bracket.


Hide 2.CONNECT BRAKE LINES

a.
C274716
1.115,0.844 0.927,0.167 0.927,0.167 0.792,0.167 false 1.375,0.969 1.448,0.208 1.448,0.208 1.594,0.208 false 1.531,1.135 1.75,0.458 1.75,0.458 1.917,0.458 false 1.656,1.292 2.063,1.292 false 0.698,2.052 0.698,2.563 0.698,2.563 0.573,2.563 false 0.51,1.719 0.667,1.063 0.667,1.063 0.781,1.063 false 0.604,0.083 0.76,0.271 0.156,0.188 10 false *1 2.094,1.208 2.281,1.375 0.188,0.167 10 false *2 1.99,0.385 2.177,0.552 0.188,0.167 10 false *3 1.646,0.115 1.833,0.281 0.188,0.167 10 false *4 0.813,0.99 1,1.156 0.188,0.167 10 false *5 0.385,2.49 0.531,2.656 0.146,0.167 10 false *6

Temporarily install each brake line to the correct positions of the actuator assembly with bracket as shown in the illustration.

HINT:
·

*1: to front wheel cylinder RH

·

*2: to front wheel cylinder LH

·

*3: to rear wheel cylinder RH

·

*4: to rear wheel cylinder LH

·

*5: from front master cylinder

·

*6: from rear master cylinder




b.

Using a union nut wrench, tighten each brake line.

Torque:
15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 3.CONNECT CONNECTOR

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the actuator connector can be connected smoothly. Do not allow water, oil or dirt to enter.



a.
C194694

Connect the brake actuator connector and push the lock lever downward.


Hide 4.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 5.BLEED BRAKE SYSTEM

Hide 6.INSTALL AIR CLEANER CASE SUB-ASSEMBLY