Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)
RM30B0U _59 Vehicle Exterior _010076 WINDOW / GLASS _0058468 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  TERMINALS OF ECU  


CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


a.
B318850
1.552,0.146 1.896,0.365 0.344,0.219 1.656,0.156 1.969,0.354 0.313,0.198 10 false J5

Disconnect the J5 power window regulator master switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J5-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
J5-6 (B) - J5-1 (E) L - W-B Power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


c.

Reconnect the J5 power window regulator master switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J5-3 (LED) - J5-1 (E) SB - W-B LED illumination signal Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
J5-4 (A) - J5-1 (E) LG - W-B Driver door power window motor AUTO UP output Ignition switch ON, driver door power window fully open 11 to 14 V
Ignition switch ON, driver door power window switch fully pulled up (AUTO UP position) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V
Driver door power window motor AUTO DOWN output Ignition switch ON, driver door power window fully closed 11 to 14 V
Ignition switch ON, driver door power window switch fully pushed down (AUTO DOWN position) Below 1 V
Ignition switch ON, driver door power window fully open 11 to 14 V
J5-5 (D) - J5-1 (E) W - W-B Driver door power window motor DOWN output Ignition switch ON, driver door power window switch off 11 to 14 V
Ignition switch ON, driver door power window switch pushed halfway down (Manual operation) Below 1 V
J5-8 (U) - J5-1 (E) P - W-B Driver door power window motor UP output Ignition switch ON, driver door power window switch off 11 to 14 V
Ignition switch ON, driver door power window switch pulled halfway up (Manual operation) Below 1 V
J5-16 (U) - J5-1 (E) G - W-B Front passenger door power window motor UP output Ignition switch ON, front passenger door power window switch off 11 to 14 V
Ignition switch ON, front passenger door power window switch pulled up (Manual operation) Below 1 V
J5-15 (D) - J5-1 (E) BR - W-B Front passenger door power window motor DOWN output Ignition switch ON, front passenger door power window switch off 11 to 14 V
Ignition switch ON, front passenger door power window switch pushed down (Manual operation) Below 1 V
J5-12 (U) - J5-1 (E) R - W-B Rear door LH power window motor UP output Ignition switch ON, rear LH door power window switch off 11 to 14 V
Ignition switch ON, rear LH door power window switch pulled up (Manual operation) Below 1 V
J5-13 (D) - J5-1 (E) BE - W-B Rear door LH power window motor DOWN output Ignition switch ON, rear LH door power window switch off 11 to 14 V
Ignition switch ON, rear LH door power window switch pushed down (Manual operation) Below 1 V
J5-10 (U) - J5-1 (E) G - W-B Rear door RH power window motor UP output Ignition switch ON, rear RH door power window switch off 11 to 14 V
Ignition switch ON, rear RH door power window switch pulled up (Manual operation) Below 1 V
J5-18 (D) - J5-1 (E) BR - W-B Rear door RH power window motor DOWN output Ignition switch ON, rear RH door power window switch off 11 to 14 V
Ignition switch ON, rear RH door power window switch pushed down (Manual operation) Below 1 V



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY


a.
B318851
1.542,0.177 1.833,0.406 0.292,0.229 1.635,0.208 1.948,0.406 0.313,0.198 10 false I4

Disconnect the I4 power window regulator switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Switch Condition Specified Condition
I4-3 (B) - Body ground L - Body ground Power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


c.

Reconnect the I4 power window regulator switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I4-4 (U) - Body ground Y - Body ground Front passenger door power window motor UP output Ignition switch ON, power window regulator switch assembly off Below 1 V
Ignition switch ON, power window regulator switch assembly pulled up (Manual operation) 11 to 14 V
I4-1 (D) - Body ground B - Body ground Front passenger door power window motor DOWN output Ignition switch ON, power window regulator switch assembly off Below 1 V
Ignition switch ON, power window regulator switch assembly pushed down (Manual operation) 11 to 14 V



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH


B318851
1.479,0.26 1.823,0.51 0.344,0.25 1.594,0.323 1.906,0.521 0.313,0.198 10 L1

a.

Disconnect the L1 rear power window regulator switch assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Switch Condition Specified Condition
L1-3 (B) - Body ground P - Body ground Power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


c.

Reconnect the L1 rear power window regulator switch assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L1-4 (U) - Body ground G - Body ground Rear door LH power window motor UP output Ignition switch ON, rear power window regulator switch assembly LH off Below 1 V
Ignition switch ON, rear power window regulator switch assembly LH pulled up (Manual operation) 11 to 14 V
L1-1 (D) - Body ground Y - Body ground Rear door LH power window motor DOWN output Ignition switch ON, rear power window regulator switch assembly LH off Below 1 V
Ignition switch ON, rear power window regulator switch assembly LH pushed down (Manual operation) 11 to 14 V



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH


B318851
1.479,0.26 1.823,0.51 0.344,0.25 1.594,0.323 1.906,0.521 0.313,0.198 10 K1

a.

Disconnect the K1 rear power window regulator switch assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Switch Condition Specified Condition
K1-3 (B) - Body ground L - Body ground Power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


c.

Reconnect the K1 rear power window regulator switch assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K1-4 (U) - Body ground P - Body ground Rear door RH power window motor UP output Ignition switch ON, rear power window regulator switch assembly RH off Below 1 V
Ignition switch ON, rear power window regulator switch assembly RH pulled up (Manual operation) 11 to 14 V
K1-1 (D) - Body ground W - Body ground Rear door RH power window motor DOWN output Ignition switch ON, rear power window regulator switch assembly RH off Below 1 V
Ignition switch ON, rear power window regulator switch assembly RH pushed down (Manual operation) 11 to 14 V



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


B263977
1.5,0.281 1.802,0.531 0.302,0.25 1.594,0.333 1.906,0.531 0.313,0.198 10 J3

a.

Disconnect the J3 front power window regulator motor assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J3-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
J3-2 (B) - Body ground GR - Body ground Power supply Always 11 to 14 V


c.

Reconnect the J3 front power window regulator motor assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J3-4 (AUTO) - J3-1 (GND) LG - W-B Driver door power window motor AUTO UP input Ignition switch ON, driver door power window fully open 11 to 14 V
Ignition switch ON, driver door power window moving, power window regulator master switch assembly (driver door power window regulator switch) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V
Driver door power window motor AUTO DOWN input Ignition switch ON, driver door power window fully closed 11 to 14 V
Ignition switch ON, driver door power window moving, power window regulator master switch assembly (driver door power window regulator switch) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully open 11 to 14 V
J3-5 (LED) - J3-1 (GND) SB - W-B LED illumination signal Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
J3-7 (DOWN) - J3-1 (GND) W - W-B Driver door power window motor DOWN input Ignition switch ON, power window regulator master switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, power window regulator master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V
Ignition switch ON, power window regulator master switch assembly (driver door power window regulator switch) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully open 11 to 14 V
J3-10 (UP) - J3-1 (GND) P - W-B Driver door power window motor UP input Ignition switch ON, power window regulator master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, power window regulator master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, driver door power window fully open 11 to 14 V
Ignition switch ON, power window regulator master switch assembly (driver door power window regulator switch) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V



CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


C278789
2.656,5.323 2.958,5.563 0.302,0.24 0.552,5.271 0.854,5.51 0.302,0.24 1.896,6.99 2.198,7.229 0.302,0.24 5.583,5.302 5.885,5.542 0.302,0.24 5.417,7.01 5.719,7.25 0.302,0.24 2.344,1.146 2.656,1.344 0.313,0.198 10 3B 2.708,5.365 3.021,5.563 0.313,0.198 10 3B 3.656,1.052 3.969,1.25 0.313,0.198 10 3C 4.365,1.188 4.677,1.385 0.313,0.198 10 3D 2.26,2.979 2.573,3.177 0.313,0.198 10 3A 0.604,5.302 0.917,5.5 0.313,0.198 10 3A 1.969,7.031 2.281,7.229 0.313,0.198 10 3D 5.646,5.323 5.958,5.521 0.313,0.198 10 3C 3.052,1.063 3.365,1.26 0.313,0.198 10 3E 5.479,7.052 5.792,7.25 0.313,0.198 10 3E

C278790
1.333,3.667 1.75,3.896 0.417,0.229 2.531,5.563 2.948,5.792 0.417,0.229 3.333,7.438 3.75,7.667 0.417,0.229 1.365,7.458 1.781,7.688 0.417,0.229 1.25,5.25 1.417,5.25 1.417,5.25 1.667,4.833 false 1.083,7.25 1.333,7.25 1.333,7.25 1.583,7 false 2.667,1.656 2.823,1.854 0.156,0.198 10 A 1.5,3.698 1.656,3.896 0.156,0.198 10 A 0.313,4.281 0.563,4.458 0.25,0.177 10 *A 1.083,5.167 1.333,5.344 0.25,0.177 10 *1 2.615,5.594 3.052,5.76 0.438,0.167 10 G78 3.406,7.469 3.865,7.635 0.458,0.167 10 G78 1.427,7.49 1.781,7.667 0.354,0.177 10 G79 0.917,7.167 1.167,7.344 0.25,0.177 10 *1 0.281,6.646 0.531,6.823 0.25,0.177 10 *B
*A Main Body ECU (Multiplex Network Body ECU) with 1 Connector *B Main Body ECU (Multiplex Network Body ECU) with 3 Connectors
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Connect the instrument panel junction block assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-11 (GND1) - Body ground None - Body ground Ground Always Below 1 Ω
A-30 (BECU) - Body ground None - Body ground Battery power supply Always 11 to 14 V
A-29 (ACC) - Body ground None - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
A-32 (IG) - Body ground None - Body ground Ignition switch power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


d.

Install the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


e.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G78-2 (KOFF) - Body ground R - Body ground Power window relay operation signal Ignition switch ON 11 to 14 V
Approximately 43 seconds after ignition switch turned off Below 1 V
3E-40 (FLCY) - Body ground W - Body ground Front door courtesy switch LH input Front door LH open Below 1 V
Front door LH closed Pulse generation
G78-19 (FRCY) - Body ground L - Body ground Front door courtesy switch RH input Front door RH open Below 1 V
Front door RH closed Pulse generation