Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM(for Entry Function)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0058004 SMART KEY SYSTEM(for Entry Function) Y

THEFT DETERRENT / KEYLESS ENTRY  SMART KEY SYSTEM(for Entry Function)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use these procedures to troubleshoot the smart key (for Entry Function).

·

*: Use the Techstream.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:

What? Vehicle model, system name
When? Date, time, occurrence frequency. Did it occur recently or has it been occurring for a long time?
Where? Does it occur at a specific location?
Under what conditions? Whether the doors were locked or unlocked, whether the engine switch was on (IG), whether the engine has started.
How did it happen? Problem symptoms*

·

*: Be sure to ask the customer in detail about the following points concerning the vehicle operating conditions, environment and problem, and then check for DTCs.

1.

If the entry lock/unlock function does not operate for all doors.

2.

If the entry lock function does not operate.

3.

If the entry unlock function does not operate.

4.

If both the entry lock and unlock functions do not operate.

5.

If the wireless lock and unlock functions do not operate.

6.

If there is no power even when the engine switch is pressed (does not turn on [ACC]).

7.

If the engine does not start with the push start function.

8.

If the wireless answer-back buzzer and outside warning buzzers do not sound.

9.

If an engine start was attempted by holding the electrical key transmitter sub-assembly near the engine switch and then pressing the engine switch.

10.

If the interior warning buzzers do not sound.

11.

Any other details concerning the problem.



·

If it is suspected that wave interference is likely, be sure to ask the customer in detail about the following points concerning the vehicle operating conditions, environment and problem.

1.

Specific locations where the system does not operate (such as near TV towers, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc.).

2.

Specific times when the system does not operate:

Whether or not symptoms occurred immediately after purchase or only recently.

Whether or not the symptoms occurred when the electrical key transmitter sub-assembly was near the vehicle (electrical key antenna).

3.

If the system does not operate only when near specific vehicles (there may be wave interference from the wireless systems of other vehicles).

4.

If the system operates intermittently.

5.

If the electrical key transmitter sub-assembly is bundled together with other items.

6.

If the electrical key transmitter sub-assembly is carried together with other electronic devices, such as cell phones, personal computers, portable music players, other electrical key transmitter sub-assemblies, etc. (keep the electrical key transmitter sub-assembly at least 0.1 m (0.328 ft.) away from such items).

7.

Where the electrical key transmitter sub-assembly is being kept when not in use:

Whether or not the electrical key transmitter sub-assembly being placed within 1 m (3.28 ft.) of items such as TVs, DVD recorders, induction cookers, rice cookers, dishwashers, modems, cell phones, personal computers, microwave ovens, desk or floor lamps, cordless telephones, etc.

8.

If there are electronic devices that transmit electric waves placed in the vehicle.

9.

When the transmitter battery was last replaced.

The transmitter battery can be checked roughly using the "Key Low Battery" item in the Data List.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>DATA LIST / ACTIVE TEST

10.

If the customer installed any optional components (theft deterrent devices, wireless fog lights, etc.) to the vehicle.





Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the vehicle battery voltage.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the vehicle battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Use the Techstream to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

Result:
Proceed to
CAN DTC is not output
CAN DTC is output




CAN DTC is not output

5.CHECK METER / GAUGE SYSTEM*

CAN DTC is output

5.CHECK METER / GAUGE SYSTEM*
a.

Use the Techstream to check if the meter/gauge system is functioning normally.

HINT:

If the certification ECU (smart key ECU assembly) mistakenly receives a vehicle speed signal, communication between the vehicle and the Techstream fails. Be sure to check "Vehicle Speed Meter" displayed on the Data List to make sure that the vehicle speed is not abnormal.


Result:
Proceed to
No vehicle speed signal is mistakenly received.
A vehicle speed signal is mistakenly received.




No vehicle speed signal is mistakenly received.

6.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

A vehicle speed signal is mistakenly received.

6.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
a.

Use the Techstream to check if the LIN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

Result:
Proceed to
LIN DTC is not output
LIN DTC is output




LIN DTC is not output

7.CHECK FUNCTION OF WIRELESS DOOR LOCK CONTROL SYSTEM*

LIN DTC is output

7.CHECK FUNCTION OF WIRELESS DOOR LOCK CONTROL SYSTEM*
a.

Use the Techstream to check if the wireless door lock control system is functioning normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Key System)>HOW TO PROCEED WITH TROUBLESHOOTING

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Proceed to
Wireless door lock control system DTC is not output
Wireless door lock control system DTC is output




Wireless door lock control system DTC is not output

8.CHECK FOR DTC*

Wireless door lock control system DTC is output

8.CHECK FOR DTC*
a.

Recheck for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Smart Key > Trouble Codes
50001 125
Result:
Proceed to
DTC is not output
Steering lock system DTC is output
Immobiliser system DTC is output
Smart key system (for Entry Function) DTC is output




DTC is not output

9.PERFORM SYMPTOMS TABLE

Steering lock system DTC is output

Immobiliser system DTC is output

Smart key system (for Entry Function) DTC is output

9.PERFORM SYMPTOMS TABLE
a.

Refer to Problem Symptoms Table.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>PROBLEM SYMPTOMS TABLE

Result:
Proceed to
Fault is not listed in problem symptoms table
Fault is listed in problem symptoms table




Fault is not listed in problem symptoms table

10.OVERALL ANALYSIS AND TROUBLESHOOTING*

Fault is listed in problem symptoms table

ADJUST REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

10.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

11.REPAIR OR REPLACEMENT
11.REPAIR OR REPLACEMENT
Result:
Proceed to
NEXT



NEXT

12.CHECK FOR DTC*
12.CHECK FOR DTC*
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Smart Key > Clear DTCs
50002 125

b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Smart Key > Trouble Codes
50001 125
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>DIAGNOSTIC TROUBLE CODE CHART


Result:
Proceed to
DTC is not output
Smart key system (for Entry Function) DTC is output




DTC is not output

END

Smart key system (for Entry Function) DTC is output