Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM30B0U _57 Power Source / Network _009133 NETWORKING _0059674 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2785  Communication Malfunction between ECUs Connected by LIN  


DESCRIPTION

The certification ECU intermittently monitors the LIN communication bus between the components related to certification. DTC B2785 is stored when a malfunction in the LIN communication bus between the components related to certification is detected 3 times consecutively.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2785 Communication Malfunction between ECUs Connected by LIN The certification ECU detects a malfunction in the LIN communication bus between components related to certification 3 times consecutively.
·

Certification ECU (smart key ECU assembly)

·

Steering lock actuator assembly

·

Harness or connector



WIRING DIAGRAM

B345131
2.313,0.323 2.625,0.521 0.313,0.198 10 false 17 2.01,0.458 2.323,0.656 0.313,0.198 10 false LIN 5.26,0.458 5.573,0.656 0.313,0.198 10 false LIN 5.104,0.323 5.417,0.521 0.313,0.198 10 false 5 5.01,0.938 5.323,1.135 0.313,0.198 10 false G5 5.021,1.094 7.094,1.281 2.073,0.188 10 false Steering Lock Actuator Assembly 0.531,1.052 3.375,1.292 2.844,0.24 10 false Certification ECU (Smart Key ECU Assembly) 0.552,0.885 0.865,1.083 0.313,0.198 10 false G84 0.875,1.365 2.563,1.563 1.688,0.198 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When using the Techstream with the ignition switch off to troubleshoot:

·

Connect the Techstream to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart key system.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>PRECAUTION



HINT:

When DTC B2785 and B2287 are output simultaneously, perform troubleshooting for DTC B2785 first.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Smart Key > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Smart Key > Trouble Codes
50001 125

Result:
Proceed to
DTC B2785 is output
DTC B2785 is not output



DTC B2785 is output

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - STEERING LOCK ACTUATOR ASSEMBLY)

DTC B2785 is not output

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - STEERING LOCK ACTUATOR ASSEMBLY)
a.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G5 steering lock actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G84-17 (LIN) - G5-5 (LIN) Always Below 1 Ω
G84-17 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.

Disconnect the G5 steering lock actuator assembly connector.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Smart Key > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Smart Key > Trouble Codes
50001 125

Result:
Proceed to
DTC B2785 is not output
DTC B2785 is output



DTC B2785 is not output

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

DTC B2785 is output

REPLACE STEERING LOCK ACTUATOR ASSEMBLY