CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Remove the main body ECU (multiplex network body ECU).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *A | Main Body ECU (Multiplex Network Body ECU) with 1 Connector | - | - |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
| *a | 1 Connector | - | - |
| *A | Main Body ECU (Multiplex Network Body ECU) with 3 Connectors | - | - |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
| *a | 3 Connectors | - | - |
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connectors disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A-11 (GND1) - Body ground | - | Ground | Always | Below 1 Ω |
| A-30 (BECU) - Body ground | - | Battery power supply | Always | 11 to 14 V |
| A-29 (ACC) - Body ground | - | ACC power supply | Ignition switch ACC | 11 to 14 V |
| A-29 (ACC) - Body ground | - | ACC power supply | Ignition switch off | Below 1 V |
| A-32 (IG) - Body ground | - | IG power supply | Ignition switch ON | 11 to 14 V |
| A-32 (IG) - Body ground | - | IG power supply | Ignition switch off | Below 1 V |
If the result is not as specified, there may be a malfunction in the wire harness.
CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/ Jam Protection Function)
Disconnect the J3 front power window regulator motor assembly LH connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| J3-2 (B) - Body ground | GR - Body ground | Battery power supply | Always | 11 to 14 V |
| J3-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
CHECK SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (w/ Sliding Roof System)
Disconnect the Q8 sliding roof drive gear sub-assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| Q8-8 (B) - Body ground | L - Body ground | Battery power supply | Always | 11 to 14 V |
| Q8-12 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [w/ Smart Key System]
Disconnect the G82 certification ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G82-2 (+B) - Body ground | W - Body ground | Battery power supply | Always | 11 to 14 V |
| G82-11 (E) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
CHECK STEERING LOCK ACTUATOR ASSEMBLY (w/ Smart Key System)
Disconnect the G5 steering lock actuator assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G5-7 (B) - Body ground | L - Body ground | Battery power supply | Always | 11 to 14 V |
| G5-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (w/ Automatic Air Conditioning System)
Disconnect the G81 air conditioning amplifier assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G81-1 (IG+) - Body ground | GR - Body ground | IG power supply | Ignition switch off | Below 1 V |
| G81-1 (IG+) - Body ground | GR - Body ground | IG power supply | Ignition switch ON | 11 to 14 V |
| G81-21 (B) - Body ground | GR - Body ground | Battery power supply | Always | 11 to 14 V |
| G81-14 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
CHECK AIR CONDITIONING CONTROL ASSEMBLY
Disconnect the G20 air conditioning control assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G20-8 (IG+) - Body ground | BE - Body ground | IG power supply | Ignition switch ON | 11 to 14 V |
| G20-8 (IG+) - Body ground | BE - Body ground | IG power supply | Ignition switch off | Below 1 V |
| G20-5 (GND) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |