Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › 2012.12–2013.11
RM30B0U _52 Drivetrain _010989 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0060247 AUTOMATIC TRANSAXLE SYSTEM C

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0711  Transmission Fluid Temperature Sensor "A" Performance  


DESCRIPTION

The ATF temperature sensor converts the fluid temperature into a resistance value for use by the ECM.

The ECM applies a voltage to the temperature sensor through terminal THO1 of the ECM.

The sensor resistance changes with the ATF temperature. As the temperature becomes higher, the sensor resistance decreases.

One terminal of the sensor is grounded so that the sensor resistance decreases and the voltage goes down as the temperature becomes higher.

The ECM calculates the fluid temperature based on the voltage signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0711 Transmission Fluid Temperature Sensor "A" Performance One of the following conditions (A), (B) or (C) is met:
(A) (a), (b) and (c) are detected: (2-trip detection logic)
·

(a) Intake air and engine coolant temperatures are 15°C (59°F) or higher at engine start

·

(b) Soak time is 5 hours or more

·

(c) After normal driving for over 10 min. and 5 km (3.1 mile) or more, ATF temperature is below 20°C (68°F)


(B) Both (a) and (b) are detected: (2-trip detection logic)
·

(a) Intake air and engine coolant temperatures are -10°C (14°F) or higher at engine start

·

(b) After normal driving for over 18 min. and 20 sec. and 8 km (5 mile) or more, ATF temperature is below 20°C (68°F)


(C) Both (a) and (b) are detected: (2-trip detection logic)
·

(a) Engine coolant temperature is below 35°C (95°F) at engine start

·

(b) ATF temperature is 110°C (230°F) or higher when engine coolant temperature reaches 60°C (140°F)


ATF temperature sensor (transmission wire) Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates that there is a problem with output signals from the ATF temperature sensor and that the sensor itself is defective. The ATF temperature sensor converts the ATF temperature into an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects an open or short in the ATF temperature circuit or a fault of the ATF temperature sensor.

After running the vehicle for a certain period, the ATF temperature should increase. If the ATF temperature is below 20°C (68°F) after running the vehicle for a certain period, the ECM interprets this as a fault, turns on the MIL, and stores the DTC.

MONITOR STRATEGY

Related DTCs P0711: ATF temperature sensor/Rationality check
Required sensors/Components ATF temperature sensor
Frequency of operation Continuous
Duration Condition (A), (B), (C) and (D): 3 sec.
Condition (E): Continuous
MIL operation 2 driving cycles
Sequence of operation None

TYPICAL ENABLING CONDITIONS

All
The monitor will run whenever the following DTCs are not stored P0712, P0713 (ATF temperature sensor circuit)
P0115, P0117, P0118 (ECT sensor circuit)
P0112, P0113 (IAT sensor circuit)
P0715, P0717 (Turbine speed sensor circuit)
P0791, P0793 (Intermediate shaft speed sensor circuit)
P0748 (Shift solenoid valve SL1 circuit)
P0778 (Shift solenoid valve SL2 circuit)
P0798 (Shift solenoid valve SL3 circuit)
P2810 (Shift solenoid valve SL4 circuit)
P0327, P0328 (KCS circuit)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0604, P0606, P060A, P060B, P060D, P060E, P0657, P1607, P2102, P2103, P2111, P2112, P2118, P2119, P2135 (ETCS)
U0100 (CAN communication system)
P2610 (Soak timer circuit)
ATF temperature sensor circuit Not circuit malfunction
ECT (Engine coolant temperature) sensor circuit Not circuit malfunction
IAT (Intake air temperature) sensor circuit Not circuit malfunction
Turbine speed sensor circuit Not circuit malfunction
Intermediate shaft speed sensor Not circuit malfunction
Shift solenoid valve SL1 circuit Not circuit malfunction
Shift solenoid valve SL2 circuit Not circuit malfunction
Shift solenoid valve SL3 circuit Not circuit malfunction
Shift solenoid valve SL4 circuit Not circuit malfunction
KCS (Knock control sensor) circuit Not circuit malfunction
Soak timer circuit Not circuit malfunction
ETCS (Electronic throttle control system) Not system down
CAN communication system Not system down
Time after engine start 12 sec. or more
ECT -15°C (5°F) or higher

Condition (A)
Time after engine start except for continuing shift position "N" or "P"*2 10 min. or more
Driving distance after engine start*3 5 km (3.1 miles) or more
IAT*4 15°C (59°F) or higher
ECT (12 sec. after engine start) 15°C (59°F) or higher
Soak time 5 hours or more
Accumulated driving time*1 110 sec. or more

Condition (B)
Time after engine start except for continuing shift position "N" or "P"*2 18 min. and 20 sec. or more
Driving distance after engine start*3 8 km (5 miles) or more
IAT*4 -10°C (14°F) or higher
ECT (12 sec. after engine start) -10°C (14°F) or higher
Accumulated driving time*1 200 sec. or more

Condition (C)
Time after engine start except for continuing shift position "N" or "P"*2 30 min. or more
Driving distance after engine start*3 15 km (9.3 miles) or more
IAT*4 -15°C (5°F) or higher
ECT (12 sec. after engine start) -15°C (5°F) or higher
Accumulated driving time*1 400 sec. or more

Condition (D)
Time after engine start except for continuing shift position "N" or "P"*2 40 min. or more
Driving distance after engine start*3 20 km (12.4 miles) or more
Accumulated driving time*1 550 sec. or more

Condition (E)
Time after ECT reaches 60°C (140°F) 10 sec. or more
ATF temperature (12 sec. after engine start) 110°C (230°F) or higher
ECT (12 sec. after engine start) Below 35°C (95°F)

HINT:

*1: Following conditions are met

Engine speed - Turbine speed 10 rpm or more
Output speed 400 rpm or more
Throttle valve opening angle 3% or more
Shift position Not "N" or "P"
Engine Starting
However, accumulated driving time is cleared -
When following condition met -
Duration time from shift position "N" or "P" 600 sec. or more

*2: Time after engine start is cleared when following condition met

Duration time from shift position "N" or "P" 600 sec. or more

*3: Driving distance is cleared when following condition met

Duration time from shift position "N" or "P" 600 sec. or more

*4: IAT is measured when either of following conditions met

12 sec. after engine start -
Duration time from shifting to "N" or "P" 600 sec. or more


TYPICAL MALFUNCTION THRESHOLDS

When either condition below is met: Condition (A), (B), (C) and (D) or (E)

Condition (A), (B), (C) and (D)
ATF temperature Below 20°C (68°F)

Condition (E)
ATF temperature 110°C (230°F) or higher

COMPONENT OPERATING RANGE

ATF temperature 20 to 110°C (68 to 230°F)

CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION

·
·

If DTCs P0711 and P2610 are output simultaneously, confirm that the ATF temperature is as specified in "Normal Condition" using the Techstream first. When the ATF temperature is as specified in "Normal Condition", perform troubleshooting for DTC P2610.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P2610



DATA LIST


HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the Techstream, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Temperature 1 ATF temperature sensor value Min.: -40°C (-40°F)
Max.: 215°C (419°F)
·

After stall test: Approx. 80°C (176°F)

·

Equal to ambient temperature after cold soak


If the value is "-40°C (-40°F)" or "150°C (302°F)", the ATF temperature sensor circuit is open or shorted.
Powertrain > Engine and ECT > Data List
Tester Display
A/T Oil Temperature 1
50003 234 406
HINT:

When DTC P0712 is output and the Techstream indicates 150°C (302°F) or higher, there is a short circuit.

When DTC P0713 is output and the Techstream indicates -40°C (-40°F), there is an open circuit.

Check the temperature displayed on the Techstream in order to check if a malfunction exists.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
150°C (302°F) or higher Short circuit

If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately stored (in 0.5 seconds). When P0713 is stored, P0711 cannot be stored.

It is not necessary to inspect the circuit when P0711 is stored.



PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0711)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs using the Techstream.

Result:
Result Proceed to
Only P0711 is output A
P0711 and other DTCs are output B


HINT:

If any other codes besides P0711 are output, perform troubleshooting for those DTCs first.




A

2.CHECK TRANSAXLE FLUID LEVEL

B

2.CHECK TRANSAXLE FLUID LEVEL

OK:

Automatic transaxle fluid level is correct.


Result:
Proceed to
OK
NG



OK

REPLACE ATF TEMPERATURE SENSOR (TRANSMISSION WIRE)

NG