CHECK MULTIPLEX NETWORK DOOR ECU
Disconnect the U18 and U19 multiplex network door ECU connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| U18-1 (ECUB) - Body ground | W - Body ground | Battery power supply | Always | 11 to 14 V |
| U18-7 (IG) - Body ground | W - Body ground | IG power supply | Ignition switch ON | 11 to 14 V |
| U18-7 (IG) - Body ground | W - Body ground | IG power supply | Ignition switch off | Below 1 V |
| U19-8 (B) - Body ground | W - Body ground | Battery power supply | Always | 11 to 14 V |
| U19-7 (GND) - Body ground | W-B - Body ground | Body ground | Always | Below 1 Ω |
Reconnect the U18 and U19 multiplex network door ECU connectors.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| U19-10 (DC+) - U19-9 (DC-) | B - R | Back door lock assembly (back door lock motor) circuit | Back door lock motor operating | 11 to 14 V |
| U19-10 (DC+) - U19-9 (DC-) | B - R | Back door lock assembly (back door lock motor) circuit | Back door lock motor not operating | Below 1 V |
| U18-20 (MSW) - Body ground | W - Body ground | Power back door main switch signal | Power back door main switch not pushed | Below 1 V |
| U18-20 (MSW) - Body ground | W - Body ground | Power back door main switch signal | Power back door main switch pushed | Pulse generation |
| U18-6 (BDDN) - Body ground | LG - Body ground | Door control switch signal | Door control switch assembly on | Below 1 V |
| U18-6 (BDDN) - Body ground | LG - Body ground | Door control switch signal | Door control switch assembly off | Pulse generation |
| U18-5 (BZR+) - Body ground | V - Body ground | Wireless door lock buzzer signal | Wireless door lock buzzer sounding | Pulse generation |
| U18-5 (BZR+) - Body ground | V - Body ground | Wireless door lock buzzer signal | Wireless door lock buzzer not sounding | Below 1 V |
| U18-18 (OSL) - U18-17 (OSE) | L - GR | Power back door sensor assembly LH signal | Power back door sensor assembly LH not pressed | 4 to 6 V |
| U18-18 (OSL) - U18-17 (OSE) | L - GR | Power back door sensor assembly LH signal | Power back door sensor assembly LH pressed | Below 1 V |
| U18-16 (OSR) - U18-17 (OSE) | SB - GR | Power back door sensor assembly RH signal | Power back door sensor assembly RH not pressed | 4 to 6 V |
| U18-16 (OSR) - U18-17 (OSE) | SB - GR | Power back door sensor assembly RH signal | Power back door sensor assembly RH pressed | Below 1 V |
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Key System)
Disconnect the G82 and G84 certification ECU (smart key ECU assembly) connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G82-2 (+B) - Body ground | W - Body ground | Battery power supply | Always | 11 to 14 V |
| G82-10 (CUTB) - Body ground | P - Body ground | Battery power supply | Always | 11 to 14 V |
| G84-5 (IG) - Body ground | LG - Body ground | IG power supply | Ignition switch ON | 11 to 14 V |
| G84-5 (IG) - Body ground | LG - Body ground | IG power supply | Ignition switch off | Below 1 V |
| G82-11 (E) - Body ground | BR - Body ground | Body ground | Always | Below 1 Ω |
Reconnect the G82 and G84 certification ECU (smart key ECU assembly) connectors.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G83-27 (TSW5) - Body ground | Y - Body ground | Back door opener switch assembly signal | Back door opener switch assembly off | Pulse generation |
| G83-27 (TSW5) - Body ground | Y - Body ground | Back door opener switch assembly signal | Back door opener switch assembly on | Below 1 V |
CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
Remove the main body ECU (multiplex network body ECU).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Connect the instrument panel junction block assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A-30 (BECU) -Body ground | None - Body ground | Battery power supply | Always | 11 to 14 V |
| A-29 (ACC) -Body ground | None - Body ground | ACC power supply | Ignition switch ACC | 11 to 14 V |
| A-29 (ACC) -Body ground | None - Body ground | ACC power supply | Ignition switch off | Below 1 V |
| A-32 (IG) - Body ground | None - Body ground | IG power supply | Ignition switch ON | 11 to 14 V |
| A-32 (IG) - Body ground | None - Body ground | IG power supply | Ignition switch off | Below 1 V |
| A-11 (GND1) - Body ground | None - Body ground | Body ground | Always | Below 1 Ω |
Install the main body ECU (multiplex network body ECU).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*: w/o Smart Key System |
||||
| G78-23 (BDSU) - Body ground* | R - Body ground | Back door opener switch assembly signal | Back door opener switch assembly off | Pulse generation |
| G78-23 (BDSU) - Body ground* | R - Body ground | Back door opener switch assembly signal | Back door opener switch assembly on | Below 1 V |
| G78-27 (PBDS) - Body ground | R - Body ground | Back door control switch signal | Back door control switch off | Pulse generation |
| G78-27 (PBDS) - Body ground | R - Body ground | Back door control switch signal | Back door control switch on | Below 1 V |