Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTUITIVE PARKING ASSIST SYSTEM
RM30B0U _56 Audio / Visual / Telematics _009404 PARK ASSIST / MONITORING _0062867 INTUITIVE PARKING ASSIST SYSTEM J

PARK ASSIST / MONITORING  INTUITIVE PARKING ASSIST SYSTEM  Back Sonar Sensor RH Circuit  


DESCRIPTION

The ultrasonic sensor sends and receives ultrasonic waves. Based on the received wave, the sensor calculates the approximate distance between the vehicle and the obstacle, and sends the distance value as a signal to the clearance warning ECU assembly.

WIRING DIAGRAM

E270572
4.156,2.094 5.719,2.448 1.563,0.354 10 No. 3 Ultrasonic Sensor (Rear Center Sensor LH) 4.156,1.906 4.469,2.104 0.313,0.198 10 S3 4.229,0.552 4.385,0.75 0.156,0.198 10 4 4.219,0.938 4.375,1.135 0.156,0.198 10 2 4.219,1.313 4.375,1.51 0.156,0.198 10 6 4.417,0.667 4.729,0.865 0.313,0.198 10 SO 4.396,1.042 4.708,1.24 0.313,0.198 10 BO 4.427,1.396 4.74,1.594 0.313,0.198 10 EO 2.833,0.958 2.99,1.156 0.156,0.198 10 1 2.833,0.563 2.99,0.76 0.156,0.198 10 3 2.833,1.313 2.99,1.51 0.156,0.198 10 5 2.531,0.677 2.844,0.875 0.313,0.198 10 SI 2.531,1.052 2.844,1.25 0.313,0.198 10 BI 2.542,1.406 2.854,1.604 0.313,0.198 10 EI 1.604,1.875 1.917,2.073 0.313,0.198 10 S2 1.594,2.073 3.146,2.438 1.552,0.365 10 No. 3 Ultrasonic Sensor (Rear Center Sensor RH)

PROCEDURE

1.INSPECT NO. 3 ULTRASONIC SENSOR (REAR CENTER SENSOR RH)
a.
E270573
1.958,0.896 2.375,0.479 false 1.958,1.115 2.656,1.115 false 1.958,1.365 2.417,1.74 false 0.948,0.563 1.5,0.896 false 0.792,1.115 1.469,1.115 false 1.021,1.75 1.479,1.354 false 2.729,1.031 3.042,1.229 0.313,0.198 10 SI 2.479,0.375 2.792,0.573 0.313,0.198 10 BI 2.51,1.667 2.823,1.865 0.313,0.198 10 EI 0.521,1.052 0.833,1.25 0.313,0.198 10 SO 0.615,0.458 0.927,0.656 0.313,0.198 10 BO 0.771,1.698 1.083,1.896 0.313,0.198 10 EO

Remove the No. 3 ultrasonic sensor (rear center sensor RH).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (BI) - 5 (EI) Always 10 kΩ or higher
1 (BI) - 2 (BO) Always 10 kΩ or higher
3 (SI) - 4 (SO) Always Below 1 Ω
5 (EI) - 6 (EO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (REAR CENTER SENSOR RH - REAR CENTER SENSOR LH)

NG

REPLACE NO. 3 ULTRASONIC SENSOR (REAR CENTER SENSOR RH)

2.CHECK HARNESS AND CONNECTOR (REAR CENTER SENSOR RH - REAR CENTER SENSOR LH)
a.

Disconnect the S2 No. 3 ultrasonic sensor (rear center sensor RH) connector.


b.

Disconnect the S3 No. 3 ultrasonic sensor (rear center sensor LH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S2-3 (SI) - S3-4 (SO) Always Below 1 Ω
S2-1 (BI) - S3-2 (BO) Always Below 1 Ω
S2-5 (EI) - S3-6 (EO) Always Below 1 Ω
S2-3 (SI) - Body ground Always 10 kΩ or higher
S2-1 (BI) - Body ground Always 10 kΩ or higher
S2-5 (EI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR