Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTUITIVE PARKING ASSIST SYSTEM
RM30B0U _56 Audio / Visual / Telematics _009404 PARK ASSIST / MONITORING _0062867 INTUITIVE PARKING ASSIST SYSTEM J

PARK ASSIST / MONITORING  INTUITIVE PARKING ASSIST SYSTEM  Rear Clearance Sonar Sensor LH Circuit  


DESCRIPTION

The ultrasonic sensor sends and receives ultrasonic waves. Based on the received wave, the sensor calculates the approximate distance between the vehicle and the obstacle, and sends the distance value as a signal to the clearance warning ECU assembly.

WIRING DIAGRAM

E270572
4.156,2.094 5.865,2.469 1.708,0.375 10 No. 3 Ultrasonic Sensor (Rear Corner Sensor LH) 4.156,1.906 4.469,2.104 0.313,0.198 10 S4 4.229,0.552 4.385,0.75 0.156,0.198 10 3 4.219,0.938 4.375,1.135 0.156,0.198 10 1 4.219,1.313 4.375,1.51 0.156,0.198 10 5 4.417,0.667 4.729,0.865 0.313,0.198 10 SI 4.417,1.042 4.729,1.24 0.313,0.198 10 BI 4.427,1.396 4.74,1.594 0.313,0.198 10 EI 2.833,0.958 3.083,1.177 0.25,0.219 10 12 2.833,0.563 3.052,0.76 0.219,0.198 10 14 2.833,1.302 3.052,1.5 0.219,0.198 10 13 2.417,0.677 2.802,0.875 0.385,0.198 10 SOR 2.427,1.052 2.771,1.25 0.344,0.198 10 BOR 2.542,1.406 2.854,1.604 0.313,0.198 10 E1 1.604,1.875 1.917,2.073 0.313,0.198 10 G33 1.594,2.073 3.156,2.469 1.563,0.396 10 Clearance Warning ECU Assembly

PROCEDURE

1.INSPECT NO. 3 ULTRASONIC SENSOR (REAR CORNER SENSOR LH)
a.
E270573
1.958,0.896 2.375,0.479 false 1.958,1.115 2.656,1.115 false 1.958,1.365 2.417,1.74 false 0.948,0.563 1.5,0.896 false 0.792,1.115 1.469,1.115 false 1.021,1.75 1.479,1.354 false 2.729,1.031 3.042,1.229 0.313,0.198 10 SI 2.479,0.375 2.792,0.573 0.313,0.198 10 BI 2.51,1.667 2.823,1.865 0.313,0.198 10 EI 0.521,1.052 0.833,1.25 0.313,0.198 10 SO 0.615,0.458 0.927,0.656 0.313,0.198 10 BO 0.771,1.698 1.083,1.896 0.313,0.198 10 EO

Remove the No. 3 ultrasonic sensor (rear corner sensor LH).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (BI) - 5 (EI) Always 10 kΩ or higher
1 (BI) - 2 (BO) Always 10 kΩ or higher
3 (SI) - 4 (SO) Always Below 1 Ω
5 (EI) - 6 (EO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - REAR CORNER SENSOR LH)

NG

REPLACE NO. 3 ULTRASONIC SENSOR (REAR CORNER SENSOR LH)

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - REAR CORNER SENSOR LH)
a.

Disconnect the G33 clearance warning assembly connector.


b.

Disconnect the S4 No. 3 ultrasonic sensor (rear corner sensor LH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G33-14 (SOR) - S4-3 (SI) Always Below 1 Ω
G33-12 (BOR) - S4-1 (BI) Always Below 1 Ω
G33-13 (E1) - S4-5 (EI) Always Below 1 Ω
G33-14 (SOR) - Body ground Always 10 kΩ or higher
G33-12 (BOR) - Body ground Always 10 kΩ or higher
G33-13 (E1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR