Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › VALVE BODY ASSEMBLY
RM30B0U _52 Drivetrain _010989 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0058562 VALVE BODY ASSEMBLY A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  VALVE BODY ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 1.INSTALL MANUAL VALVE

a.

Coat the manual valve with ATF and install it to the transmission valve body assembly.


Hide 2.INSTALL TRANSAXLE CASE GASKET

a.

Coat 2 new transaxle case gaskets with ATF.


b.

Install the 2 transaxle case gaskets onto the transaxle case.


Hide 3.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.
C274836
1.021,2.458 1.177,2.656 0.156,0.198 10 A 1.406,2.438 1.563,2.635 0.156,0.198 10 A 2.115,2.458 2.271,2.656 0.156,0.198 10 A 1.75,2.427 1.906,2.625 0.156,0.198 10 A 1.729,0.469 1.885,0.667 0.156,0.198 10 A 1.094,0.427 1.25,0.625 0.156,0.198 10 B 2.802,1.417 2.958,1.615 0.156,0.198 10 B 2.958,1.417 3.115,1.615 0.156,0.198 10 *a 0.094,1.99 0.25,2.188 0.156,0.198 10 B 0.063,2.167 0.219,2.365 0.156,0.198 10 *a 0.073,1.135 0.229,1.333 0.156,0.198 10 C 0.76,0.427 0.917,0.625 0.156,0.198 10 D 0.688,2.604 0.844,2.802 0.156,0.198 10 B
*a Positioning Bolt


Coat the O-ring of the transmission wire with ATF.


b.

Insert the pin of the manual valve lever into the groove on the end of the manual valve and install the transmission valve body assembly onto the automatic transaxle assembly with the 11 bolts.

Torque:
Bolt A, B, C : 10.8 N*m (110 kgf*cm, 8 ft.*lbf)
Bolt D : 9.6 N*m (98 kgf*cm, 85 in.*lbf)

NOTICE:
·

When installing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and automatic transaxle assembly to interfere with each other.

·

Be sure to insert the pin of the manual valve lever into the groove on the end of the manual valve.

·

First, temporarily install the bolts marked *a in the illustration because they are positioning bolts.



HINT:

Bolt length:

Bolt A: 25 mm (0.984 in.)

Bolt B: 30 mm (1.18 in.)

Bolt C and D: 35 mm (1.38 in.)



Hide 4.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.

Coat a new O-ring with ATF and install it to the valve body oil strainer assembly.

NOTICE:

Ensure that the O-ring is not twisted or pinched.



b.

Install the valve body oil strainer assembly onto the transmission valve body assembly with the 2 bolts.

Torque:
9.6 N*m (98 kgf*cm, 85 in.*lbf)


Hide 5.INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.
C201701
2.748,0.131 2.969,0.338 0.222,0.207 10 *1 2.716,0.222 1.774,0.222 1.774,0.222 1.774,0.753 false 2.494,0.222 2.494,1.165 false
*1 Transmission Oil Cleaner Magnet


Install the 2 transmission oil cleaner magnets onto the automatic transaxle oil pan sub-assembly as shown in the illustration.


b.

Install a new automatic transaxle oil pan gasket onto the automatic transaxle oil pan sub-assembly.


c.
C202902

Install the automatic transaxle oil pan sub-assembly with the automatic transaxle oil pan gasket onto the automatic transaxle assembly with the 17 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

NOTICE:

Completely remove any oil or grease from the contact surface of the automatic transaxle assembly and automatic transaxle oil pan sub-assembly with the automatic transaxle oil pan gasket before installation.



d.
C202903

Clean and degrease the 2 bolts and the installation hole in the automatic transaxle assembly.


e.

Apply adhesive to 2 or 3 threads on the ends of the bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



f.

Install the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 6.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH

a.

Install the front suspension member reinforcement LH with the 4 bolts.

Torque:
96 N*m (979 kgf*cm, 71 ft.*lbf)


Hide 10.RESET MEMORY

NOTICE:

If automatic transaxle parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION