Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY
RM30B0U _51 Engine / Hybrid System _009173 2AR-FE ENGINE MECHANICAL _0050875 ENGINE ASSEMBLY A

2AR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

As the engine assembly with transaxle is extremely heavy, the engine lifter may suddenly drop if the instructions listed in the repair manual are not followed. Therefore, always follow the instructions listed in the repair manual when performing this procedure.


NOTICE:

for Manual Transaxle:

When the transaxle is removed, be sure to use a new clutch release with bearing cylinder and new installation bolts. Removal of the transaxle allows the compressed clutch release with bearing cylinder to return to its original position, and dust could damage the seal of the clutch release with bearing cylinder, possibly causing clutch fluid leaks.


HINT:

Perform "Inspection After Repairs" after replacing the engine assembly, cylinder head sub-assembly, camshaft, No. 2 camshaft, camshaft timing gear assembly, camshaft timing exhaust gear assembly, piston sub-assembly or piston ring.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.

Install the wire harness clamp bracket with the bolt.

Torque:
7.7 N*m (79 kgf*cm, 68 in.*lbf)


b.
A297339
0.917,1.51 1.042,1.688 0.125,0.177 10 3 2.729,0.573 2.854,0.75 0.125,0.177 10 4 1.031,0.375 1.156,0.552 0.125,0.177 10 1 2.635,1.51 2.76,1.688 0.125,0.177 10 2

Temporarily install the engine mounting insulator LH with the 4 bolts.


c.

Tighten the 4 bolts in the sequence shown in the illustration.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 2.INSTALL ENGINE MOUNTING SPACER

HINT:

Perform this procedure only when replacement of the engine mounting spacer is necessary.


a.
A297331
0.552,1.5 0.708,1.698 0.156,0.198 10 2 2.427,0.635 2.583,0.833 0.156,0.198 10 1

Temporarily install the engine mounting spacer with the 2 bolts.


b.

Tighten the 2 bolts in the sequence shown in the illustration.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 3.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.

Install the radiator reservoir bracket with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.
A297340
1.115,0.073 1.271,0.271 0.156,0.198 10 2 2.594,1.292 2.75,1.49 0.156,0.198 10 1 0.708,1.927 0.865,2.125 0.156,0.198 10 3

Temporarily install the engine mounting insulator sub-assembly RH with the 3 bolts.


c.

Tighten the 3 bolts in the sequence shown in the illustration.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 4.INSTALL REAR ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


a.
A297341
2.219,1.823 2.375,2.021 0.156,0.198 10 3 2.656,1.563 2.813,1.76 0.156,0.198 10 2 0.646,1.646 0.802,1.844 0.156,0.198 10 1 1.313,1.813 1.469,2.01 0.156,0.198 10 4

Temporarily install the rear engine mounting insulator with the 2 bolts and 2 nuts.


b.

Tighten the 2 bolts and 2 nuts in the sequence shown in the illustration.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 5.INSTALL FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


a.

Install the front engine mounting insulator with the 2 bolts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 7.REMOVE ENGINE FROM ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.



a.

Attach a sling device and hang the engine with a chain block.


b.

Lift the engine and remove it from the engine stand.


Hide 9.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine.


Hide 10.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 12.INSTALL TRANSFER ASSEMBLY (for AWD)

Hide 13.INSTALL STARTER ASSEMBLY

Hide 14.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Temporarily install the front engine mounting insulator with the through bolt and nut.


b.
A302705
1.021,2.771 1.167,2.771 1.167,2.771 1.458,3.26 true 1.646,3.198 2.354,3.208 2.354,3.208 1.604,3.385 true 2.396,3.135 2.583,3.302 0.188,0.167 10 false *1 0.823,2.688 1.01,2.854 0.188,0.167 10 false *2
*1 Alignment Mark
*2 Protrusion


Temporarily install the front suspension crossmember with the through bolt.

HINT:

When installing the suspension crossmember, align the protrusion of the engine mounting bracket with the alignment mark of the engine mounting insulator.



c.

Place the engine on an engine lifter.

HINT:

Place the engine on wooden blocks or equivalent so that the engine is level.



d.

Operate the engine lifter and install the engine to the vehicle.

CAUTION:

Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:
·

Make sure that the engine is clear of all wiring and hoses.

·

While raising the engine into the vehicle, do not allow it to contact the vehicle.




e.
A296309

Temporarily install the front suspension crossmember with the 2 bolts.


f.
A296308

Temporarily install the member rear brace RH and LH with the 6 bolts.


g.

Install the engine mounting insulator LH with the through bolt and nut.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)

NOTICE:

While holding the bolt in place, tighten the nut.



h.
A297332
1.146,0.365 1.302,0.563 0.156,0.198 10 A 2.042,1.594 2.198,1.792 0.156,0.198 10 B
V100135

Bolt
V100136

Nut


Install the engine mounting insulator RH with the bolt and 2 nuts.

Torque:
for bolt and nut A : 95 N*m (969 kgf*cm, 70 ft.*lbf)
for nut B : 52 N*m (530 kgf*cm, 38 ft.*lbf)


i.
A296309

Tighten the 2 front suspension member bolts.

Torque:
137 N*m (1397 kgf*cm, 101 ft.*lbf)


j.
A297333
0.844,1.104 0.833,1.167 false
V100135

Bolt A
V100136

Bolt B


Tighten the 6 member rear brace bolts.

Torque:
for bolt A : 137 N*m (1397 kgf*cm, 101 ft.*lbf)
for bolt B : 93 N*m (948 kgf*cm, 69 ft.*lbf)


k.

Remove the 2 bolts and No. 1 and No. 2 engine hangers.


l.
A297334
0.563,0.646 0.531,0.729 false
V100135

Bolt A
V100136

Bolt B


Install the front crossmember with the 6 bolts.

Torque:
for bolt A : 96 N*m (979 kgf*cm, 71 ft.*lbf)
for bolt B : 95 N*m (969 kgf*cm, 70 ft.*lbf)


m.

Tighten the through bolt of the rear engine mounting insulator.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

HINT:

Check that the protrusion of the engine mounting bracket is aligned with the alignment mark of the engine mounting insulator.



n.
A297351

Tighten the through bolt and nut of the front engine mounting insulator.

Torque:
145 N*m (1479 kgf*cm, 107 ft.*lbf)

NOTICE:

While holding the nut in place, tighten the through bolt.



Hide 15.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH

a.

Install the front suspension member reinforcement LH with the 4 bolts.

Torque:
96 N*m (979 kgf*cm, 71 ft.*lbf)


Hide 16.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH

a.

Install the front suspension member reinforcement RH with the 4 bolts.

Torque:
96 N*m (979 kgf*cm, 71 ft.*lbf)


Hide 17.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for AWD)

Hide 19.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover.


Hide 20.INSTALL FRONT EXHAUST PIPE SUB-ASSEMBLY

Hide 21.INSTALL FRONT NO. 2 EXHAUST PIPE SUB-ASSEMBLY

Hide 22.INSTALL DRIVE SHAFT BEARING BRACKET

a.

Install the bracket with the 3 bolts.

Torque:
63.7 N*m (650 kgf*cm, 47 ft.*lbf)


Hide 26.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 27.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 28.CONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 29.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 30.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

Hide 31.CONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 32.CONNECT FRONT SPEED SENSOR LH

Hide 33.CONNECT FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 34.INSTALL FRONT AXLE SHAFT NUT LH

Hide 35.INSTALL FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure described for the LH side.


Hide 36.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 37.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 38.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 39.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Connect the transmission control cable to the control cable bracket with a new clip.


b.

Connect the transmission control cable to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 40.CONNECT WIRE HARNESS AND HOSE

a.

Connect the heater hose to the cylinder head sub-assembly, and slide the clip to secure it.


b.

Connect the heater hose to the No. 1 water by-pass pipe, and slide the clip to secure it.


c.

Connect the vacuum hose to the No. 1 hose to hose tube, and slide the clip to secure it.


d.

Connect the wire harness with the bolt.

Torque:
11.4 N*m (116 kgf*cm, 8 ft.*lbf)


e.

Connect the 2 connectors, attach the 2 claws to the engine room No. 1 relay block and connect the wire harness.


f.

Connect the wire harness to the engine room No. 1 relay block with the nut.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


g.

Connect the wire harness with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


h.

Connect the 2 clamps and wire harness.


i.

Connect the clamp.


j.

Connect the starter wire with the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


k.

Install the terminal cap.


Hide 41.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube connector.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM>PRECAUTION


b.

Install the No. 1 fuel pipe clamp.


Hide 43.CONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 44.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 45.CONNECT RADIATOR HOSE SUB-ASSEMBLY

Hide 46.INSTALL RADIATOR HOSE HOSE CLAMP

Hide 47.CONNECT NO. 2 RADIATOR HOSE

Hide 49.INSTALL FAN AND GENERATOR V BELT

Hide 50.CONNECT RADIATOR RESERVOIR ASSEMBLY

Hide 52.INSTALL FRONT BATTERY BRACKET

Hide 55.INSTALL BATTERY INSULATOR

Hide 56.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 58.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 59.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 60.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 62.ADD TRANSFER OIL (for AWD)

Hide 74.INSTALL FRONT FLOOR COVER

Hide 75.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 76.INSTALL REAR ENGINE UNDER COVER RH

a.

Install the rear engine under cover RH with the 3 clips.


Hide 77.INSTALL REAR ENGINE UNDER COVER LH

a.

Install the rear engine under cover LH with the 3 clips.


Hide 78.INSTALL NO. 1 ENGINE UNDER COVER

a.

Install the No. 1 engine under cover with the 2 screws, 4 bolts and 8 clips.