Home › Drivetrain › U760F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT
RM30B0U _52 Drivetrain _009030 U760F AUTOMATIC TRANSMISSION / TRANSAXLE _0058586 AUTOMATIC TRANSAXLE UNIT A

U760F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

a.
C134951

Using a screwdriver, remove the transmission breather hose sub-assembly from the automatic transaxle assembly.

NOTICE:

Be careful not to damage the transaxle case.


HINT:

Tape the screwdriver tip before use.



b.
C134952
2.927,2.396 2.927,2.677 false 2,2.521 2.438,2.521 false 1.635,1.698 1.99,1.698 false 0.635,0.875 0.792,0.604 0.792,0.604 0.927,0.604 false 1.469,1.625 1.635,1.781 0.167,0.156 10 *2 0.958,0.531 1.135,0.688 0.177,0.156 10 *1 1.844,2.448 2,2.604 0.156,0.156 10 *3 2.875,2.688 3.042,2.854 0.167,0.167 10 *4
*1 No. 1 Breather Plug
*2 Breather Plug Hose
*3 No. 2 Breather Plug
*4 O-Ring


Remove the No. 1 breather plug from the breather plug hose.


c.

Remove the No. 2 breather plug from the breather plug hose.


d.

Remove the O-ring from the No. 2 breather plug.


Hide 2.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C136685

Remove the nut, washer, and transmission control shaft lever from the control shaft.


b.
C136686

Remove the 2 bolts and the park/neutral position switch assembly from the transaxle case.

NOTICE:

Before removing the park/neutral position switch assembly, remove any dirt or rust on the installation portion of the manual valve lever shaft sub-assembly. Be sure to remove the switch straight along the shaft while being careful not to deform the plate spring that supports the shaft. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.



Hide 3.REMOVE OIL COOLER TUBE UNION

a.
C279449

Using a 19 mm union nut wrench remove the 2 oil cooler tube unions from the transaxle case.


b.

Remove the 2 O-rings from the 2 oil cooler tube unions.


Hide 4.REMOVE TRANAXLE CASE PLUG

a.
C134959

Using a 6 mm hexagon socket wrench, remove the 3 transaxle case plugs from the transaxle housing.


b.

Remove the 3 gaskets from the 3 transaxle case plugs.


c.
C279453

Remove the 6 transaxle case plugs from the transaxle case and rear transaxle cover sub-assembly.


d.

Using a screwdriver, remove the 6 O-rings from the 6 transaxle case plugs.

NOTICE:

Be careful not to damage the transaxle case plugs.


HINT:

Tape the screwdriver tip before use.



Hide 5.SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY

a.
C230613

Support the automatic transaxle assembly on wooden blocks.


Hide 6.REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.
C201309

Using a 6 mm hexagon socket wrench, remove the overflow plug from the automatic transaxle oil pan sub-assembly.


b.

Remove the gasket from the overflow plug.


c.
C201310

Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle oil pan sub-assembly.


d.
C279454

Remove the 19 bolts, automatic transaxle oil pan sub-assembly and automatic transaxle oil pan gasket from the automatic transaxle assembly.

NOTICE:

Some fluid will remain in the automatic transaxle oil pan sub-assembly. Remove all the bolts, and carefully remove the automatic transaxle oil pan sub-assembly.



e.

Remove the 2 transmission oil cleaner magnets from the automatic transaxle oil pan sub-assembly.


Hide 8.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

a.
C201313

Remove the 2 bolts and valve body oil strainer assembly from the transmission valve body assembly.


b.
C201703
1.229,0.375 0.938,0.375 false 0.74,0.302 0.948,0.49 0.208,0.188 10 *1
*1 O-ring


Remove the O-ring from the valve body oil strainer assembly.


Hide 9.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

a.
C201315

Remove the 11 bolts and transmission valve body assembly from the transaxle case.

NOTICE:

When removing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and the transaxle case to interfere with each other.



Hide 10.REMOVE TRANSAXLE CASE GASKET

a.
C201316

Remove the 2 transaxle case gaskets from the transaxle case.


Hide 12.REMOVE REFILL PLUG

a.
C230614

Remove the refill plug from the rear transaxle cover sub-assembly.


b.

Remove the gasket from the refill plug.


Hide 13.REMOVE REAR TRANSAXLE COVER SUB-ASSEMBLY

a.
C279455

Remove the 14 bolts from the rear transaxle cover sub-assembly.


b.

Using a brass bar and a hammer, tap on the circumference of the rear transaxle cover sub-assembly to remove the rear transaxle cover sub-assembly from the transaxle case.


c.
C274807

Remove the 3 O-rings from the transaxle case.


d.
C202908
1.385,1.75 1.385,0.125 1.385,0.125 1.885,0.125 false 1.604,1.635 1.604,0.125 false 0.698,2.438 0.5,2.563 0.5,2.563 0.5,2.646 false 1.021,0.719 1.115,0.719 1.115,0.719 1.115,1.823 false 1.917,0.031 2.125,0.219 0.208,0.188 10 *1 0.823,0.615 1.01,0.938 0.188,0.323 10 *2 0.448,2.656 0.719,2.958 0.271,0.302 10 *3
*1 Oil Seal Ring
*2 Thrust Needle Roller Bearing
*3 Thrust Needle Roller Bearing Race


Using a screwdriver, remove the 2 oil seal rings from the rear transaxle cover sub-assembly.

NOTICE:

Be careful not to damage the rear transaxle cover sub-assembly.


HINT:

Tape the screwdriver tip before use.



e.

Remove the thrust needle roller bearing and thrust needle roller bearing race from the rear transaxle cover sub-assembly.


f.
C201318

Using a T30 "TORX" socket wrench, remove the 2 "TORX" screws and rear transaxle cover plate from the rear transaxle cover sub-assembly.


g.
C194888
0.792,2.385 1.01,2.385 1.01,2.385 1.51,0.906 true 0.5,2.323 0.813,2.5 0.313,0.177 10 SST 3.031,0.427 3.208,0.604 0.177,0.177 10 *a 0.323,0.844 0.5,1.021 0.177,0.177 10 *b
*a Turn
*b Hold


Using SST, remove the needle roller bearing from the rear transaxle cover sub-assembly.

SST
09319-60020  


Hide 14.REMOVE DIRECT MULTIPLE DISC CLUTCH ASSEMBLY

a.
C202901
0.604,1.281 0.365,1.552 0.365,1.552 0.365,2.094 false 2.281,0.219 2.021,0.219 2.021,0.219 2.146,1.375 false 2.323,0.146 2.5,0.313 0.177,0.167 10 *1 0.313,2.115 0.49,2.271 0.177,0.156 10 *2
*1 Thrust Needle Roller Bearing
*2 Direct Multiple Disc Clutch Assembly


Remove the direct multiple disc clutch assembly from the transaxle case.


b.

Remove the thrust needle roller bearing from the direct multiple disc clutch assembly.


c.
C224456
1.771,0.229 1.948,0.229 false 1.625,1.917 1.458,1.917 false 1.979,0.156 2.167,0.323 0.188,0.167 10 *1 1.302,1.844 1.49,2.01 0.188,0.167 10 *2
*1 O-ring
*2 Oil Seal Ring


Using a screwdriver, remove the O-ring from the direct multiple disc clutch assembly.

NOTICE:

Be careful not to damage the direct multiple disc clutch assembly.


HINT:

Tape the screwdriver tip before use.



d.

Using a screwdriver, remove the oil seal ring from the direct multiple disc clutch assembly.

NOTICE:

Be careful not to damage the direct multiple disc clutch assembly.


HINT:

Tape the screwdriver tip before use.



Hide 15.REMOVE REAR PLANETARY SUN GEAR ASSEMBLY

a.
C279456

Using a snap ring expander, remove the snap ring from the direct multiple disc clutch assembly.


b.
C201321
1.302,0.292 0.531,0.406 0.531,0.406 0.531,0.469 false 0.49,0.479 0.667,0.667 0.177,0.188 10 *1
*1 Rear Planetary Sun Gear Assembly


Remove the rear planetary sun gear assembly from the direct multiple disc clutch assembly.


c.
C201526
2.125,0.885 2.24,1 2.24,1 2.24,1.323 false 1.365,0.115 1.708,0.115 1.708,0.115 1.865,0.198 false 1.219,0.052 1.396,0.208 0.177,0.156 10 *1 2.188,1.333 2.365,1.51 0.177,0.177 10 *2
*1 Thrust Needle Roller Bearing
*2 Thrust Needle Roller Race


Remove the thrust needle roller bearing and thrust needle roller race from the direct multiple disc clutch assembly.


Hide 17.REMOVE TRANSAXLE HOUSING

a.
C205233

Remove the 20 bolts from the transaxle housing.


b.

Using a brass bar and a hammer, tap on the circumference of the transaxle housing to remove the transaxle housing from the transaxle case.


Hide 18.REMOVE COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING OUTER RACE

a.
C201323
2.527,0.393 2.858,0.535 0.332,0.141 10 SST 2.492,0.475 2.117,0.475 false

Using SST, remove the counter driven gear front tapered roller bearing outer race and shim from the transaxle housing.

SST
09308-00010  


Hide 19.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING OUTER RACE

a.
C201324
2.802,0.313 2.688,0.313 2.688,0.313 2.344,0.552 false 2.844,0.24 3.135,0.406 0.292,0.167 10 SST

Using SST, remove the front differential case front tapered roller bearing outer race and shim from the transaxle housing.

SST
09308-00010  


Hide 20.REMOVE TRANSAXLE CASE OIL SEAL RH (OUTER)

a.
C201325
1.813,0.615 2.833,0.417 2.833,0.417 1.875,1.188 true 2.875,0.313 3.188,0.49 0.313,0.177 10 SST

Using SST, and a hammer, tap out the transaxle case oil seal RH (outer) from the transaxle housing.

SST
09950-60010  (09951-00550)
09950-70010  (09951-07200)


Hide 21.REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE

a.
C201326

Remove the bolt, clamp, and differential gear lube apply tube from the transaxle housing.


Hide 22.REMOVE TRANSAXLE HOUSING OIL SEPARATOR

a.
C201327

Remove the 3 bolts and transaxle housing oil separator from the transaxle housing.


Hide 23.REMOVE OIL PUMP ASSEMBLY

a.
C201328
0.781,0.198 0.594,0.198 false 0.448,0.125 0.604,0.313 0.156,0.188 10 *1
*1 O-ring


Remove the O-ring from the oil pump assembly.


b.

Remove the 7 bolts and oil pump assembly from the transaxle case.


c.
C201329

Remove the O-ring from the oil pump assembly.


d.
C205236
1.361,0.62 1.523,0.78 0.162,0.16 10 *1 1.353,0.982 1.515,1.142 0.162,0.16 10 *2 0.938,1.422 1.101,1.582 0.162,0.16 10 *3 1.881,0.711 1.546,0.711 false 1.874,1.073 1.539,1.073 false 1.414,1.507 1.126,1.507 false
*1 Thrust Needle Roller Race
*2 Thrust Needle Roller Bearing
*3 O-ring


Remove the thrust needle roller bearing and thrust bearing race from the counter drive gear nut.


e.

Remove the O-ring from the transaxle case.


Hide 24.REMOVE NO. 3 BRAKE DISC

a.
C281635
1.802,1.021 1.99,1.573 1.99,1.573 2.125,1.573 true 2.167,1.49 2.479,1.688 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, remove the snap ring from the oil pump assembly.

NOTICE:

Be careful not to damage the oil pump assembly.


HINT:

Tape the screwdriver tip before use.



b.

Remove the 2 No. 3 brake flanges, 3 No. 3 brake discs, and 2 No. 3 brake plates from the oil pump assembly.


Hide 26.REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY

a.
C136458

Remove the underdrive planetary gear assembly from the oil pump assembly.


Hide 27.REMOVE NO. 3 BRAKE HUB

a.
C136454

Remove the No. 3 brake hub from the underdrive planetary gear assembly.


b.
C202906
1.146,0.208 1.271,0.208 1.271,0.208 1.469,0.344 false 1.188,1.115 1.271,1.115 1.271,1.115 1.469,0.948 false 1.01,0.146 1.188,0.313 0.177,0.167 10 *1 1.031,1.052 1.271,1.365 0.24,0.313 10 *2
*1 Thrust Needle Roller Race
*2 Thrust Needle Roller Bearing


Remove the thrust needle roller bearing and thrust needle roller race from the underdrive planetary gear assembly.


Hide 28.REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C201331
1.271,0.302 1.385,0.302 1.385,0.302 1.646,0.854 false 1.552,3.031 1.26,3.031 false 2.438,1.396 2.333,1.396 2.333,1.396 1.979,2.146 false 1.115,0.24 1.281,0.406 0.167,0.167 10 *1 1.104,2.969 1.292,3.135 0.188,0.167 10 *3 2.469,1.333 2.667,1.51 0.198,0.177 10 *2
*1 Planetary Sun Gear Sub-assembly
*2 Underdrive Planetary Gear Assembly
*3 Snap Ring


While expanding the snap ring with snap ring pliers, remove the planetary sun gear sub-assembly from the underdrive planetary gear assembly.


b.

Remove the snap ring from the underdrive planetary gear assembly.


Hide 29.INSPECT UNDERDRIVE PLANETARY GEAR ASSEMBLY

Hide 31.REMOVE INPUT SHAFT SUB-ASSEMBLY

a.
C136459

Remove the input shaft sub-assembly from the oil pump assembly.


b.
C202905
1.156,1.01 1.344,1.01 false 0.938,2.208 1.479,2.208 false 1.719,2.802 2.333,2.479 2.333,2.479 1.74,3.135 false 1.74,2.979 2.333,2.479 false 1.115,0.188 1.25,0.188 1.25,0.188 1.427,0.365 false 0.969,0.094 1.125,0.271 0.156,0.177 10 *1 0.979,0.906 1.167,1.26 0.188,0.354 10 *2 0.771,2.115 0.938,2.302 0.167,0.188 10 *3 2.365,2.375 2.583,2.552 0.219,0.177 10 *4
*1 Thrust Needle Roller Race
*2 Thrust Needle Roller Bearing
*3 Input Shaft Sub-assembly
*4 Oil Seal Ring


Remove the thrust needle roller bearing and thrust needle roller race from the input shaft sub-assembly.


c.

Using a screwdriver, remove the 3 oil seal rings from the input shaft sub-assembly.

NOTICE:

Be careful not to damage the input shaft sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 32.REMOVE UNDERDRIVE PLANETARY SUN GEAR

a.
C202904
2.313,1.396 2.229,1.396 2.229,1.396 2.01,1.313 false 0.979,0.49 1.406,0.49 false 0.833,0.396 1.01,0.573 0.177,0.177 10 *1 2.354,1.292 3.26,1.635 0.906,0.344 10 *2
*1 Underdrive Planetary Sun Gear
*2 Thrust Needle Roller Bearing


Remove the underdrive planetary sun gear from the oil pump assembly.


b.

Remove the thrust needle roller bearing from the oil pump assembly.


Hide 33.REMOVE NO. 1 BRAKE DISC

a.
C153477
2.198,0.583 2.49,0.583 false 2.188,1.188 2.323,1.188 2.323,1.188 2.323,0.594 false 1.24,0.885 1.042,0.885 false 2.521,0.49 2.688,0.646 0.167,0.156 10 *1 0.875,0.792 1.042,0.948 0.167,0.156 10 *2
*1 Snap Ring
*2 Brake Snap Ring Stopper


Using a screwdriver, remove the 2 snap rings and brake snap ring stopper from the oil pump assembly.

NOTICE:

Be careful not to damage the oil pump assembly.


HINT:

Tape the screwdriver tip before use.



b.

Remove the No. 1 brake flange, 3 No. 1 brake discs, and 3 No. 1 brake plates from the oil pump assembly.


Hide 35.REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C136464

Remove the 3 2nd brake piston return spring sub-assemblies from the oil pump assembly.


Hide 36.INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 37.REMOVE NO. 1 BRAKE PISTON

a.
C136465

Holding the oil pump assembly by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil pump assembly to remove the No. 1 brake piston.


b.
C274846

Using a screwdriver, remove the 2 O-rings from the No. 1 brake piston.

NOTICE:

Be careful not to damage the No. 1 brake piston.


HINT:

Tape the screwdriver tip before use.



Hide 38.REMOVE FRONT DIFFERENTIAL CASE

a.
C205237

Remove the front differential case from the transaxle case.


Hide 39.REMOVE COUNTER DRIVE GEAR NUT

a.
C201333
1.24,0.125 1.333,0.125 1.333,0.125 1.906,0.844 false 0.958,0.052 1.281,0.219 0.323,0.167 10 SST

Using SST and a hammer, unstake the counter drive gear nut.

SST
09930-00010  


b.
C201334
1.151,3.98 1.291,4.135 0.14,0.154 10 P

Turn the manual valve lever shaft counterclockwise to set it to the P position as shown in the illustration.


c.
C201527
0.927,0.292 1.031,0.292 1.031,0.292 1.823,1 false 0.635,0.219 0.969,0.396 0.333,0.177 10 SST

Using SST, remove the counter drive gear nut from the front planetary gear assembly.

SST
09387-00130  


d.
C201335
1.487,4.004 1.625,4.186 0.137,0.182 10 N

Turn the manual valve lever shaft 2 notches clockwise to set it to the N position as shown in the illustration.


Hide 40.REMOVE COUNTER DRIVEN GEAR

a.
C201336

Remove the counter driven gear from the transaxle case.


Hide 41.REMOVE COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING

a.
C194890
1.438,0.594 1.583,0.74 1.583,0.74 1.438,1.219 false 1.583,0.74 1.063,1.188 false 2.219,0.49 2.875,0.219 2.875,0.219 2.771,0.667 false 1.604,0.052 1.771,0.24 0.167,0.188 10 *a 0.094,0.667 0.26,0.854 0.167,0.188 10 *b 1.615,0.656 2.021,0.823 0.406,0.167 10 SST 2.906,0.115 3.271,0.281 0.365,0.167 10 SST
*a Turn
*b Hold


Using SST, remove the counter driven gear front tapered roller bearing from the counter driven gear.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60010  (09951-00320)


Hide 42.REMOVE COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING

HINT:

If removing the counter driven gear rear tapered roller bearing, replace the counter driven gear with a new one.


Hide 43.REMOVE PAWL SHAFT CLAMP

a.
C201339

Remove the bolt and pawl shaft clamp from the transaxle case.


Hide 44.REMOVE NO. 1 TRANSMISSION CASE PLATE

a.
C201340

Remove the bolt and No. 1 transmission case plate from the transaxle case.


Hide 45.REMOVE PAWL STOPPER PLATE

a.
C201341

Remove the 2 bolts and pawl stopper plate from the transaxle case.


Hide 46.REMOVE PARKING LOCK SLEEVE

a.
C201342

Remove the parking lock sleeve from the transaxle case.


Hide 47.REMOVE PARKING LOCK PAWL

a.
C201343
0.583,1.448 0.677,1.448 0.677,1.448 0.969,1.542 false 0.906,0.156 0.802,0.156 0.802,0.156 1.031,1.229 false 1.594,0.49 1.521,0.49 1.521,0.49 1.396,1.292 false 2.531,1.385 2.417,1.385 2.417,1.385 2.052,1.677 false 0.427,1.323 0.604,1.5 0.177,0.177 10 *3 0.927,0.042 1.125,0.198 0.198,0.156 10 *1 1.625,0.385 1.802,0.563 0.177,0.177 10 *2 2.563,1.26 2.719,1.427 0.156,0.167 10 *4
*1 Parking Lock Pawl Pin
*2 Parking Lock Pawl Shaft
*3 Spring
*4 Parking Lock Pawl


Remove the spring, parking lock pawl pin, parking lock pawl shaft, and parking lock pawl from the transaxle case.


Hide 48.REMOVE COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING OUTER RACE

a.
C201344
1.375,0.521 1.781,0.521 false 1.083,0.458 1.417,0.604 0.333,0.146 10 SST

Using SST, remove the counter driven gear rear tapered roller bearing outer race from the transaxle case.

SST
09308-00010  


Hide 49.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING OUTER RACE

a.
C196814
0.248,0.361 0.566,0.545 0.318,0.184 10 SST 0.614,0.444 0.781,0.444 false 2.699,1.409 3.017,1.593 0.318,0.184 10 SST 2.859,1.178 2.859,1.393 false

Using SST, remove the front differential case rear tapered roller bearing outer race from the transaxle case.

SST
09308-00010  


Hide 50.REMOVE TRANSAXLE CASE OIL SEAL LH

a.
C138709
1.375,1.219 0.385,0.458 0.385,0.458 1.229,1.365 true 0.104,0.385 0.427,0.573 0.323,0.188 10 SST

Using SST, and a hammer, tap out the transaxle case oil seal LH from the transaxle case.

SST
09950-60010  (09951-00650)
09950-70010  (09951-07100)


Hide 51.REMOVE ONE-WAY CLUTCH ASSEMBLY

a.
C281634
1.885,0.302 2.052,0.302 2.052,0.302 2.292,1.177 true 1.698,0.219 2.01,0.375 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver, remove the snap ring from the transaxle case.

NOTICE:

Be careful not to damage the transaxle case.


HINT:

Tape the screwdriver tip before use.



b.
C141526
1.75,0.99 2.292,0.99 false 0.75,0.354 1.198,0.354 false 2.333,0.906 2.542,1.073 0.208,0.167 10 *2 0.594,0.271 0.781,0.417 0.188,0.146 10 *1
*1 One-way Clutch Assembly with Planetary Ring Gear
*2 Thrust Needle Roller Bearing


Remove the one-way clutch assembly with the planetary ring gear from the transaxle case.


c.

Remove the thrust needle roller bearing from the front planetary gear assembly.


d.
C201345
0.875,0.125 0.969,0.125 0.969,0.125 1.271,0.406 false 1.115,1.438 1.375,1.438 false 2.521,1 2.802,1.073 2.802,1.073 2.802,1.156 false 0.719,0.021 0.875,0.208 0.156,0.188 10 *1 0.948,1.344 1.115,1.521 0.167,0.177 10 *3 2.75,1.156 2.938,1.354 0.188,0.198 10 *2
*1 One-way Clutch Assembly
*2 Outer Race Retainer
*3 Planetary Ring Gear


Remove the one-way clutch assembly from the planetary ring gear.


e.

Remove the outer race retainer from the one-way clutch assembly.


Hide 53.REMOVE PLANETARY RING GEAR FLANGE

a.
C136480
1.26,0.646 0.958,0.646 false 0.938,2.292 1.198,2.292 false 2.125,1.375 2.438,1.375 false 0.771,2.177 0.948,2.344 0.177,0.167 10 *3 2.479,1.26 2.646,1.417 0.167,0.156 10 *2 0.802,0.531 0.979,0.698 0.177,0.167 10 *1
*1 Snap Ring
*2 Planetary Ring Gear Flange
*3 Planetary Ring Gear


Using a screwdriver, remove the snap ring from the planetary ring gear.

NOTICE:

Be careful not to damage the planetary ring gear.


HINT:

Tape the screwdriver tip before use.



b.

Remove the planetary ring gear flange from the planetary ring gear.


Hide 54.REMOVE NO. 2 BRAKE DISC

a.
C281633
2.125,1.146 1.917,0.302 1.917,0.302 1.74,0.302 true 1.573,0.229 1.885,0.385 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver, remove the snap ring from the transaxle case.

NOTICE:

Be careful not to damage the transaxle case.


HINT:

Tape the screwdriver tip before use.



b.

Remove the No. 2 brake flange, 4 No. 2 brake discs, and 4 No. 2 brake plates from the transaxle case.


Hide 56.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C281631
2.135,1.135 1.885,0.302 1.885,0.302 1.698,0.302 true 1.531,0.229 1.844,0.385 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver, remove the snap ring from the transaxle case.

NOTICE:

Be careful not to damage the transaxle case.


HINT:

Tape the screwdriver tip before use.



b.
C136484

Remove the 1st and reverse brake return spring sub-assembly from the transaxle case.


Hide 57.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

Hide 58.REMOVE NO. 2 BRAKE PISTON

a.
C136485

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the ATF hole to remove the No. 2 brake piston from the transaxle case.


b.
C201346

Using a screwdriver, remove the 2 O-rings from the No. 2 brake piston.

NOTICE:

Be careful not to damage the No. 2 brake piston.


HINT:

Tape the screwdriver tip before use.



Hide 59.REMOVE FRONT PLANETARY GEAR ASSEMBLY

a.
C136674
2.62,1.242 2.966,1.407 0.346,0.166 10 SST 1.76,1.752 2.585,1.334 2.585,1.334 1.884,2.015 false

Using SST and a press, remove the front planetary gear assembly from the transaxle case.

SST
09950-60010  (09951-00580)
09950-70010  (09951-07100)


Hide 60.REMOVE COUNTER DRIVE GEAR

NOTICE:

Perform this procedure only when the counter drive gear bearing or transaxle case is replaced.


a.
C201347
2.8,0.45 3.199,0.624 0.399,0.174 10 SST 1.733,2.566 2.132,2.74 0.399,0.174 10 SST 1.741,0.978 2.743,0.564 2.743,0.564 1.855,1.196 false 0.988,2.477 1.695,2.672 1.695,2.672 1.223,3.105 false

Using SST and a press, remove the counter drive gear and bearing inner race (rear side) from the transaxle case.

SST
09950-60020  (09951-00710)
09950-70010  (09951-07100)


b.
C201348

As shown in the illustration, tighten the 2 bolts evenly and leave a clearance of approximately 5.0 mm (0.197 in.) between the counter drive gear and bearing inner race (front side).


c.
C201349
0.272,1.178 0.612,1.336 0.34,0.158 10 *b 2.408,0.063 2.712,0.221 0.305,0.158 10 *a 0.254,1.729 0.563,1.889 0.308,0.161 10 SST 0.835,1.535 0.614,1.783 0.614,1.783 1.279,1.363 false 1.253,1.545 0.627,1.775 false 0.88,1.221 0.614,1.783 false
*a Turn
*b Hold


Using SST, remove the bearing inner race (front side) from the counter drive gear.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60020  (09951-00710)


Hide 61.REMOVE NO. 3 BRAKE PISTON

a.
C201350
1.491,0.214 1.79,0.362 0.299,0.148 10 SST 1.839,0.302 1.931,0.302 1.931,0.302 2.078,0.603 false

Place SST on the brake piston return spring and compress the brake piston return spring with a press.

SST
09387-00070  


b.

Using a screwdriver, remove the snap ring from the transaxle case.

NOTICE:

Be careful not to damage the transaxle case.


HINT:

Tape the screwdriver tip before use.



c.
C201351
1.333,0.146 1.51,0.146 1.51,0.146 1.615,0.844 false 1.167,0.073 1.354,0.24 0.188,0.167 10 *1
*1 Brake Piston Return Spring


Remove the brake piston return spring from the transaxle case.


d.
C201352
1.104,0.219 1.198,0.219 1.198,0.219 1.417,0.708 false 0.948,0.125 1.146,0.292 0.198,0.167 10 *1
*1 No. 3 Brake Piston


Remove the No. 3 brake piston from the transaxle case.


e.
C201353

Using a screwdriver, remove the 2 O-rings from the No. 3 brake piston.

NOTICE:

Be careful not to damage the No. 3 brake piston.


HINT:

Tape the screwdriver tip before use.



Hide 62.INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 63.REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY

a.
C201354

Remove the bolt, manual detent spring cover, and manual detent spring sub-assembly from the transaxle case.


Hide 64.REMOVE PARKING LOCK ROD SUB-ASSEMBLY

a.
C201355

Remove the parking lock rod sub-assembly from the manual valve lever shaft sub-assembly.

HINT:

Align the slot with the notches on the manual valve lever shaft sub-assembly to remove the parking lock rod sub-assembly.



Hide 65.REMOVE MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY

a.
C201356

Using needle-nose pliers, remove the manual valve lever shaft retainer spring from the transaxle case.


b.
C201357

Remove the manual valve lever shaft sub-assembly from the transaxle case.


Hide 66.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

a.
C281368
2.865,1.729 2.729,1.729 2.729,1.729 2.448,0.906 true 2.917,1.656 3.229,1.813 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver, remove the manual valve lever shaft oil seal from the transaxle case.

NOTICE:

Be careful not to damage the transaxle case.


HINT:

Tape the screwdriver tip before use.