Home › Drivetrain › U760F AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE
RM30B0U _52 Drivetrain _009030 U760F AUTOMATIC TRANSMISSION / TRANSAXLE _0058589 DIFFERENTIAL CASE A

U760F AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL DIFFERENTIAL SIDE GEAR

a.
C278985
2.594,0.448 2.927,0.448 false 0.76,0.396 1.094,0.396 false 0.771,0.729 1.104,0.729 false 1.438,1.625 1.771,1.625 false 1.448,1.927 1.781,1.927 false 1.948,0.51 1.813,0.51 1.813,0.51 1.76,0.781 false 0.792,1.583 0.74,1.854 0.74,1.854 0.604,1.854 false 1.188,1 1.521,1 false 1.021,1.385 1.354,1.385 false 3,0.365 3.313,0.521 0.313,0.156 10 false *1 0.583,0.646 0.896,0.802 0.313,0.156 10 false *2 0.573,0.302 0.885,0.458 0.313,0.156 10 false *3 1.406,1.313 1.719,1.469 0.313,0.156 10 false *4 2,0.438 2.313,0.594 0.313,0.156 10 false *5 1.833,1.844 2.146,2 0.313,0.156 10 false *3 1.823,1.542 2.135,1.698 0.313,0.156 10 false *2 0.438,1.771 0.75,1.927 0.313,0.156 10 false *5 1.01,0.927 1.323,1.083 0.313,0.156 10 false *4
*1 Differential Case
*2 Differential Side Gear
*3 No. 1 Front Differential Side Gear Thrust Washer
*4 Front Differential Pinion
*5 Front Differential Pinion Thrust Washer


Coat the 2 differential side gears, 2 No. 1 front differential side gear thrust washers, 2 front differential pinions and 2 front differential pinion thrust washers with ATF and install them to the differential case.


Hide 2.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C138706

Coat the front No. 1 differential pinion shaft with ATF, and install it to the differential case.


Hide 3.INSPECT DIFFERENTIAL SIDE GEAR BACKLASH

Hide 4.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C138707

Using a 5 mm pin punch and hammer, install the front differential pinion shaft straight pin.

NOTICE:

Align the holes, and install the front differential pinion shaft straight pin.



b.
C138711

Using a chisel and hammer, stake the differential case.

NOTICE:

Stake the differential case after adjusting the backlash.



Hide 5.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C201521
1.865,0.813 2.406,0.688 2.406,0.688 1.875,0.958 false 1.75,0.656 2.406,0.688 false 2.458,0.615 2.771,0.76 0.313,0.146 10 SST

Using SST and a press, install a new front differential case rear tapered roller bearing to the front differential case.

SST
09710-30012  (09710-04081)
09950-60010  (09951-00480)
09950-70010  (09951-07100)

NOTICE:

Do not damage the bearing cage during bearing inner race installation.



Hide 6.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C274853
1.771,0.302 2.427,0.302 2.427,0.302 1.865,0.75 false 1.865,0.479 2.427,0.302 false 2.469,0.229 2.927,0.427 0.458,0.198 10 SST

Using SST and a press, install a new front differential case front tapered roller bearing to the differential case.

SST
09523-36010  
09950-60010  (09951-00540)
09950-70010  (09951-07100)

NOTICE:

Do not damage the bearing cage during bearing inner race installation.



Hide 7.INSTALL FRONT DIFFERENTIAL RING GEAR

a.

Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

NOTICE:

Do not heat the ring gear to more than 110°C (230°F).



b.
C138531
1.25,1.438 1.01,0.604 1.01,0.604 1.167,1.5 false 0.854,0.448 1.01,0.615 0.156,0.167 10 *a
*a Matchmark


Clean the contact surface of the differential case.


c.

Align the matchmarks, set the differential ring gear to the front differential case.


d.
C138532

Install the 12 bolts.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)

NOTICE:
·

Tighten the bolts after the front differential ring gear has cooled down sufficiently.

·

Tighten the bolts evenly in a diagonal pattern using several steps.




Hide 8.INSTALL TRANSAXLE CASE OIL SEAL RH (INNER)

a.

Coat the lip of a new transaxle case oil seal RH (inner) with MP grease.


b.
C196918
0.792,1.031 0.448,0.396 0.448,0.396 0.854,0.698 true 2.313,1.01 1.781,0.302 1.781,0.302 2.406,0.615 true 0.135,0.292 0.594,0.49 0.458,0.198 10 SST 1.458,0.219 1.917,0.417 0.458,0.198 10 SST

Using SST and a hammer, install the transaxle case oil seal RH (inner).

SST
09950-60010  (09951-00410)
09950-70010  (09951-07200)

Oil seal drive in depth:

21.5 to 22.5 mm (0.847 to 0.885 in.)