Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2013.11
RM30B0U _57 Power Source / Network _009133 NETWORKING _0050933 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

·

After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION





JUNCTION CONNECTOR


a.

No. 1 CAN Junction Connector (for 2 Pin Connector Type)

HINT:

Connectors that connect to the No. 1 CAN junction connector can be distinguished by the color of their CAN bus wires. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


C253921
5.229,2.802 5.438,2.594 5.438,2.594 5.646,2.594 true 5.229,3 5.438,3.271 5.438,3.271 5.646,3.271 true 0.052,0.063 0.365,0.219 0.313,0.156 10 *1 2.01,1.76 2.438,1.917 0.427,0.156 10 G118 4.25,2.208 4.563,2.365 0.313,0.156 10 *a 2.021,1.979 2.448,2.135 0.427,0.156 10 G119 2.021,2.198 2.448,2.354 0.427,0.156 10 G120 2.021,2.417 2.448,2.573 0.427,0.156 10 G121 2.021,2.646 2.448,2.802 0.427,0.156 10 G122 2.021,2.865 2.448,3.021 0.427,0.156 10 G123 2.021,3.083 2.448,3.24 0.427,0.156 10 G124 2.021,3.313 2.448,3.469 0.427,0.156 10 G125 5.667,2.521 6.094,2.677 0.427,0.156 10 CANH 5.667,3.198 6.094,3.354 0.427,0.156 10 CANL
*1 No. 1 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
- -


No. 1 CAN Junction Connector Wiring Color Connect to

*: w/ Lane Departure Alert System

G118-1 (CANH) L No. 3 CAN junction connector
G118-2 (CANL) W
G119-1 (CANH) V No. 2 CAN junction connector
G119-2 (CANL) W
G120-1 (CANH) R Brake actuator assembly (skid control ECU)
G120-2 (CANL) W
G121-1 (CANH) LG Power steering ECU assembly
G121-2 (CANL) W
G122-1 (CANH) P Spiral with sensor cable sub-assembly (steering angle sensor)
G122-2 (CANL) W
G123-1 (CANH) Y Main body ECU (multiplex network body ECU)
G123-2 (CANL) W
G124-1 (CANH) B DLC3
G124-2 (CANL) W
G125-1 (CANH) G Lane departure warning camera*
G125-2 (CANL) W


b.

No. 2 CAN Junction Connector (for 2 Pin Connector Type)

HINT:

Connectors that connect to the No. 2 CAN junction connector can be distinguished by the color of their CAN bus wires. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


C278783
5.229,2.833 5.417,2.563 5.417,2.563 5.563,2.563 true 5.229,2.979 5.448,3.24 5.448,3.24 5.594,3.24 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *1 2.021,1.76 2.438,2.021 0.417,0.26 10 false G128 4.25,2.25 4.563,2.406 0.313,0.156 10 false *a 2.031,1.979 2.448,2.24 0.417,0.26 10 false G129 2.021,2.198 2.438,2.458 0.417,0.26 10 false G130 2.031,2.427 2.448,2.688 0.417,0.26 10 false G126 2.021,2.646 2.438,2.906 0.417,0.26 10 false G131 2.031,2.865 2.448,3.125 0.417,0.26 10 false G132 2.031,3.083 2.448,3.344 0.417,0.26 10 false G133 5.625,2.458 6.146,2.667 0.521,0.208 10 false CANH 5.625,3.135 6.146,3.344 0.521,0.208 10 false CANL
*1 No. 2 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
- -


No. 2 CAN Junction Connector Wiring Color Connect to

*1: w/ Navigation System

*2: w/ Audio and Visual System (for Radio and Display Type)

*3: for AWD

*4: w/ Smart Key System

G126-1 (CANH) B Air conditioning amplifier assembly
G126-2 (CANL) W
G128-1 (CANH) G Combination meter assembly
G128-2 (CANL) W
G129-1 (CANH) V No. 1 CAN junction connector
G129-2 (CANL) W
G130-1 (CANH) Y
·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2


G130-2 (CANL) W
G131-1 (CANH) L 4WD ECU assembly*3
G131-2 (CANL) W
G132-1 (CANH) R Certification ECU (smart key ECU assembly)*4
G132-2 (CANL) W
G133-1 (CANH) BR Airbag sensor assembly
G133-2 (CANL) W


c.

No. 3 CAN Junction Connector (for 2 Pin Connector Type)

HINT:

Connectors that connect to the No. 3 CAN junction connector can be distinguished by the color of their CAN bus wires. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


C278780
5.25,2.833 5.417,2.5 5.417,2.5 5.583,2.5 true 5.25,3 5.417,3.25 5.417,3.25 5.583,3.25 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *1 2.031,1.76 2.344,1.958 0.313,0.198 10 false N27 5.667,2.417 6.167,2.667 0.5,0.25 10 false CANH 5.667,3.167 6.167,3.417 0.5,0.25 10 false CANL 4.25,2.219 4.563,2.417 0.313,0.198 10 false *a 2.031,1.979 2.344,2.177 0.313,0.198 10 false N28 2.031,2.198 2.344,2.396 0.313,0.198 10 false N29
*1 No. 3 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 3 CAN Junction Connector)
- -


No. 3 CAN Junction Connector Wiring Color Connect to

*: w/ Blind Spot Monitor System

N27-1 (CANH) Y ECM
N27-2 (CANL) W
N28-1 (CANH) L No. 1 CAN junction connector
N28-2 (CANL) W
N29-1 (CANH) R Blind spot monitor sensor LH*
N29-2 (CANL) W


d.

No. 4 CAN Junction Connector (for 22 Pin Connector Type)

C235392
3.354,0.281 3.771,0.531 0.417,0.25 4.031,1.469 4.198,1.688 4.198,1.688 4.417,1.688 true 4.01,1.333 4.208,1.115 4.208,1.115 4.427,1.115 true 3.917,1.323 4.188,0.875 4.188,0.875 4.354,0.875 true 3.833,1.313 4.146,0.646 4.146,0.646 4.323,0.646 true 3.833,1.458 4.115,2.073 4.115,2.073 4.333,2.073 true 3.927,1.448 4.146,1.885 4.146,1.885 4.365,1.885 true 3.74,1.333 4.104,0.396 4.104,0.396 4.281,0.396 true 3.646,1.323 4.031,0.177 4.031,0.177 4.208,0.177 true 3.74,1.458 4.042,2.292 4.042,2.292 4.26,2.292 true 3.646,1.458 4,2.542 4,2.542 4.219,2.542 true 2.74,1.198 2.906,1.198 2.906,1.198 3.083,1.323 true 2.771,1.677 2.938,1.677 2.938,1.677 3.083,1.458 true 2.781,1.677 2.948,1.677 2.948,1.677 3.094,1.458 true 2.813,1.875 2.979,1.875 2.979,1.875 3.177,1.458 true 2.781,0.99 2.948,0.99 2.948,0.99 3.177,1.344 true 2.771,0.75 2.938,0.75 2.938,0.75 3.281,1.333 true 2.917,2.073 3.083,2.073 3.083,2.073 3.271,1.469 true 2.969,2.344 3.135,2.344 3.135,2.344 3.375,1.458 true 2.844,0.479 3.01,0.479 3.01,0.479 3.354,1.323 true 3.125,2.563 3.292,2.563 3.292,2.563 3.458,1.458 true 2.865,0.229 3.031,0.229 3.031,0.229 3.458,1.323 true 4.479,0.99 5.396,1.188 0.917,0.198 10 false CANH*b 0.083,0.052 1,0.25 0.917,0.198 10 false *a 4.396,0.76 5.313,0.958 0.917,0.198 10 false CANH*c 4.365,0.531 5.281,0.729 0.917,0.198 10 false CANH*d 4.438,1.76 5.354,1.958 0.917,0.198 10 false CANL*c 4.375,1.958 5.292,2.156 0.917,0.198 10 false CANL*d 4.469,1.563 5.385,1.76 0.917,0.198 10 false CANL*b 3.406,0.323 4.323,0.521 0.917,0.198 10 false G134 4.333,0.292 5.25,0.49 0.917,0.198 10 false CANH*e 4.26,0.063 5.177,0.26 0.917,0.198 10 false CANH*f 4.302,2.177 5.219,2.375 0.917,0.198 10 false CANL*e 4.271,2.427 5.188,2.625 0.917,0.198 10 false CANL*f 2.292,0.375 3.208,0.573 0.917,0.198 10 false CANH*h 2.25,0.625 3.167,0.823 0.917,0.198 10 false CANH*i 2.271,0.875 3.188,1.073 0.917,0.198 10 false CANH*j 2.198,1.083 3.115,1.281 0.917,0.198 10 false CANH*k 2.271,1.552 3.188,1.75 0.917,0.198 10 false CANL*k 2.323,1.771 3.24,1.969 0.917,0.198 10 false CANL*j 2.396,1.958 3.313,2.156 0.917,0.198 10 false CANL*i 2.448,2.208 3.365,2.406 0.917,0.198 10 false CANL*h 2.323,0.094 3.24,0.292 0.917,0.198 10 false CANH*g 2.594,2.438 3.51,2.635 0.917,0.198 10 false CANL*g
*a Rear view of wire harness connector
(to No. 4 Junction Connector)
*b for Airbag Sensor Assembly
*c for Air Conditioning Amplifier Assembly *d for Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)
*e for Power Steering ECU Assembly *f for Main Body ECU (Multiplex Network Body ECU)
*g for Radio and Display Receiver Assembly *h for 4WD ECU Assembly
*i for Combination Meter Assembly *j for DLC3
*k for No. 21 CAN Junction Connector - -


No. 4 CAN Junction Connector Wiring Color Connect to
G134-1 (CANH) BR Airbag sensor assembly
G134-12 (CANL) W
G134-2 (CANH) V Air conditioning amplifier assembly
G134-13 (CANL) W
G134-3 (CANH) P Spiral with sensor cable sub-assembly (steering angle sensor)
G134-14 (CANL) W
G134-4 (CANH) LG Power steering ECU assembly
G134-15 (CANL) W
G134-5 (CANH) Y Main body ECU (multiplex network body ECU)
G134-16 (CANL) W
G134-7 (CANH) GR Radio and display receiver assembly
G134-18 (CANL) W
G134-8 (CANH) L 4WD ECU assembly
G134-19 (CANL) W
G134-9 (CANH) G Combination meter assembly
G134-20 (CANL) W
G134-10 (CANH) B DLC3
G134-21 (CANL) W
G134-11 (CANH) R No. 21 CAN junction connector
G134-22 (CANL) W


e.

No. 5 CAN Junction Connector (w/ Seat Memory)

C234761
3.375,0.521 3.771,0.813 0.396,0.292 3.344,1.417 3.146,0.656 3.146,0.656 2.948,0.656 true 3.219,1.417 2.917,0.854 2.917,0.854 2.688,0.854 true 3.208,1.667 2.958,2.104 2.958,2.104 2.729,2.104 true 3.365,1.667 3.156,2.385 3.156,2.385 2.823,2.385 true 4.188,0.771 3.969,0.771 3.969,0.771 3.51,1.427 true 4.104,2.135 3.885,2.135 3.885,2.135 3.51,1.688 true 3.448,0.583 3.906,0.781 0.458,0.198 10 N30 0.156,0.146 0.615,0.344 0.458,0.198 10 *a 2.406,0.563 3.021,0.75 0.615,0.188 10 CANH*c 2.208,2.021 2.823,2.208 0.615,0.188 10 CANL*b 2.146,0.781 2.76,0.969 0.615,0.188 10 CANH*b 2.302,2.302 2.917,2.49 0.615,0.188 10 CANL*c 4.135,2.042 4.75,2.229 0.615,0.188 10 CANL*d 4.229,0.667 4.844,0.854 0.615,0.188 10 CANL*d
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b for Main Body ECU (Multiplex Network Body ECU)
*c for No. 6 CAN Junction Connector *d for Position Control ECU and Switch Assembly


No. 5 CAN Junction Connector Wiring Color Connect to
N30-1 (CANH) B Main body ECU (multiplex network body ECU)
N30-7 (CANL) W
N30-2 (CANH) V No. 6 CAN junction connector
N30-8 (CANL) W
N30-3 (CANH) R Position control ECU and switch assembly
N30-9 (CANL) W


f.

No. 6 CAN Junction Connector (w/ Power Back Door System)

C235392
4.417,1.25 4.833,1.5 0.417,0.25 3.365,1.292 2.917,0.667 2.917,0.667 2.667,0.667 true 3.26,1.313 2.813,0.865 2.813,0.865 2.583,0.865 true 3.177,1.313 2.833,1.083 2.833,1.083 2.583,1.083 true 3.177,1.469 2.833,1.75 2.833,1.75 2.583,1.75 true 3.271,1.479 2.927,1.906 2.927,1.906 2.677,1.906 true 3.354,1.5 3.104,2.167 3.104,2.167 2.854,2.167 true 2.115,0.594 3.031,0.792 0.917,0.198 10 CANH*b 0.083,0.052 1,0.25 0.917,0.198 10 *a 2.031,0.781 2.948,0.979 0.917,0.198 10 CANH*c 2.021,1.01 2.938,1.208 0.917,0.198 10 CANH*d 2.167,1.833 3.083,2.031 0.917,0.198 10 CANL*c 2.063,1.667 2.979,1.865 0.917,0.198 10 CANL*d 2.333,2.083 3.25,2.281 0.917,0.198 10 CANL*b 4.5,1.302 5.417,1.5 0.917,0.198 10 N32
*a Rear view of wire harness connector
(to No. 6 Junction Connector)
*b for Multiplex Network Door ECU
*c for No. 7 CAN Junction Connector *d
·

for No. 5 CAN Junction Connector (w/ Seat Memory)

·

for Main Body ECU (Multiplex Network Body ECU) (w/o Seat Memory)




No. 6 CAN Junction Connector Wiring Color Connect to

*1: w/ Seat Memory

*2: w/o Seat Memory

N32-8 (CANH) G Multiplex network door ECU
N32-19 (CANL) W
N32-9 (CANH) L No. 7 CAN junction connector
N32-20 (CANL) W
N32-10 (CANH) V*1, B*2
·

No. 5 CAN junction connector*1

·

Main body ECU (multiplex network body ECU)*2


N32-21 (CANL) W


g.
C210060
0.271,0.969 0.688,1.219 0.417,0.25 1.646,0.219 1.5,0.219 1.5,0.219 1.354,0.885 true 2.167,0.458 2.021,0.458 2.021,0.458 1.719,0.885 true 1.688,0.135 2.25,0.313 0.563,0.177 10 CANH*b 0.354,1.021 0.656,1.198 0.302,0.177 10 N31 2.219,0.375 2.781,0.552 0.563,0.177 10 CANL*b 0.156,0.115 0.719,0.292 0.563,0.177 10 *a
*a Rear view of wire harness connector
(to No. 7 CAN Junction Connector)
*b for No. 6 CAN Junction Connector


No. 7 CAN Junction Connector (w/ Power Back Door System)

No. 7 CAN Junction Connector Wiring Color Connect to
N31-2 (CANL) W No. 6 CAN junction connector
N31-3 (CANH) L


h.

No. 21 CAN Junction Connector (for 22 Pin Connector Type)

C235392
2.292,1.313 2.708,1.563 0.417,0.25 4.021,1.458 4.208,1.792 4.208,1.792 4.427,1.792 true 4.01,1.333 4.208,1.115 4.208,1.115 4.427,1.115 true 3.917,1.323 4.104,0.833 4.104,0.833 4.323,0.833 true 3.833,1.313 4,0.563 4,0.563 4.219,0.563 true 3.833,1.458 4.031,2.25 4.031,2.25 4.25,2.25 true 3.917,1.458 4.135,2.031 4.135,2.031 4.354,2.031 true 4.479,1.021 5.396,1.219 0.917,0.198 10 CANH*b 0.083,0.052 1,0.25 0.917,0.198 10 *a 4.375,0.75 5.292,0.948 0.917,0.198 10 CANH*c 4.271,0.469 5.188,0.667 0.917,0.198 10 CANH*d 4.396,1.927 5.313,2.125 0.917,0.198 10 CANL*c 4.292,2.167 5.208,2.365 0.917,0.198 10 CANL*d 4.469,1.698 5.385,1.896 0.917,0.198 10 CANL*b 2.385,1.354 3.302,1.552 0.917,0.198 10 A72
*a Rear view of wire harness connector
(to No. 21 Junction Connector)
*b for Brake Actuator Assembly (Skid Control ECU)
*c for ECM *d for No. 4 CAN Junction Connector


No. 21 CAN Junction Connector Wiring Color Connect to
A72-1 (CANH) L Brake actuator assembly (skid control ECU)
A72-12 (CANL) W
A72-2 (CANH) Y ECM
A72-13 (CANL) W
A72-3 (CANH) R No. 4 CAN junction connector
A72-14 (CANL) W



CHECK DLC3


a.
C253362
0.167,1 0.583,1.25 0.417,0.25 1.948,0.906 2.167,0.417 2.167,0.417 2.417,0.417 true 1.583,0.906 1.25,0.5 1.25,0.5 1,0.5 true 1.927,1.49 1.667,1.917 1.667,1.917 1.417,1.917 true 2.333,1.5 2.5,1.833 2.5,1.833 2.75,1.833 true 0.25,1.052 0.708,1.25 0.458,0.198 10 G14 0.75,0.417 1.208,0.615 0.458,0.198 10 CG 2.469,0.344 2.927,0.542 0.458,0.198 10 CANH 1.031,1.844 1.49,2.042 0.458,0.198 10 CANL 2.802,1.76 3.26,1.958 0.458,0.198 10 BAT 0.094,0.063 0.406,0.219 0.313,0.156 10 *a
*a Front view of DLC3


Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION




b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G14-6 (CANH) - G14-14 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G14-6 (CANH) - G14-4 (CG) B - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G14-14 (CANL) - G14-4 (CG) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G14-6 (CANH) - G14-16 (BAT) B - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G14-14 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM


C228683
5.281,0.26 5.74,0.51 0.458,0.25 2.438,0.24 2.896,0.49 0.458,0.25 4.781,1.031 4.448,0.365 4.448,0.365 4.229,0.365 true 4.781,1.135 4.417,0.604 4.417,0.604 4.24,0.604 true 2.667,1.042 2.365,0.51 2.365,0.51 2.125,0.51 true 6.125,1.031 6.469,0.604 6.469,0.604 6.719,0.604 true 4.875,1.052 4.542,0.146 4.542,0.146 4.323,0.146 true 4.875,1.146 4.5,2.24 4.5,2.24 4.323,2.24 true 5.375,0.302 5.833,0.5 0.458,0.198 10 A62 2.552,0.292 3.01,0.49 0.458,0.198 10 B77 3.677,0.271 4.354,0.479 0.677,0.208 10 CANH*A 3.708,0.521 4.708,0.729 1,0.208 10 CANL*A 1.906,0.438 2.365,0.635 0.458,0.198 10 E1 6.76,0.521 7.156,0.677 0.396,0.156 10 BATT 3.771,0.052 4.448,0.26 0.677,0.208 10 CANP*B 3.75,2.156 4.427,2.365 0.677,0.208 10 CANN*B
*A V Bus *B Local Bus


a.

Disconnect the ECM connectors.

C229008
1.656,0.51 2.073,0.76 0.417,0.25 4.771,0.583 5.188,0.833 0.417,0.25 1.438,1.396 1,0.917 1,0.917 0.75,0.917 true 2.604,1.448 2.948,2.115 2.948,2.115 3.135,2.115 true 2.594,1.365 2.885,0.927 2.885,0.927 3.094,0.927 true 4.844,1.406 4.417,0.75 4.417,0.75 4.26,0.75 true 2.531,1.375 2.823,0.573 2.823,0.573 3.031,0.573 true 2.531,1.458 2.865,2.375 2.865,2.375 3.052,2.375 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 0.344,0.833 0.75,1.073 0.406,0.24 10 BATT 3.135,0.844 3.771,1.094 0.635,0.25 10 CANH*A 1.729,0.552 2.135,0.792 0.406,0.24 10 A62 4.063,0.667 4.469,0.906 0.406,0.24 10 E1 4.833,0.625 5.24,0.865 0.406,0.24 10 B77 3.156,2.042 3.74,2.302 0.583,0.26 10 CANL*A 3.063,0.479 3.698,0.729 0.635,0.25 10 CANP*B 3.104,2.271 3.688,2.531 0.583,0.26 10 CANN*B
*A V Bus *B Local Bus
*a Front view of wire harness connector
(to ECM)
- -



b.

Measure the resistance according to the value(s) in the table below.

V Bus
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A62-13 (CANH) - A62-26 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A62-13 (CANH) - B77-16 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-26 (CANL) - B77-16 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-13 (CANH) - A62-1 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A62-26 (CANL) - A62-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Local Bus
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A62-12 (CANP) - A62-25 (CANN) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A62-12 (CANP) - B75-16 (E1) B - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-25 (CANN) - B75-16 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-12 (CANP) - A62-1 (BATT) B - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A62-25 (CANN) - A62-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


C278790
2.51,5.542 2.927,5.792 0.417,0.25 1.333,7.385 1.75,7.635 0.417,0.25 3.333,7.385 3.75,7.635 0.417,0.25 1.302,3.656 1.719,3.906 0.417,0.25 3.875,5.792 4.167,6.25 4.167,6.25 4.333,6.25 true 3.167,6.198 3.417,6.198 3.417,6.198 3.781,5.781 true 3.49,8.188 3.833,8.583 3.833,8.583 4,8.583 true 3,8.583 3.167,8.583 3.167,8.583 3.396,8.177 true 1.271,8.583 1.438,8.583 1.438,8.583 1.667,8.177 true 1.771,8.156 2.052,7.583 2.052,7.583 2.219,7.583 true 1.25,4.844 1.5,4.844 false 1.25,7.042 1.5,7.042 false 2.417,3.417 2.583,3.417 2.583,3.417 3,3.781 true 5.333,3.417 5.167,3.417 5.167,3.417 4.771,3.771 true 0.25,4.26 0.917,4.417 0.667,0.156 10 *A 0.25,6.604 0.563,6.76 0.313,0.156 10 *B 2.604,6.115 3.25,6.354 0.646,0.24 10 CANH*C 2.25,7.51 2.833,7.833 0.583,0.323 10 CANP*D 1.083,4.76 1.396,4.917 0.313,0.156 10 *1 4.396,6.167 5.042,6.406 0.646,0.24 10 CANL*C 0.708,8.5 1.375,8.74 0.667,0.24 10 CANN*D 2.583,5.583 2.896,5.74 0.313,0.156 10 G78 3.417,7.427 3.729,7.583 0.313,0.156 10 G78 4.063,8.51 4.708,8.75 0.646,0.24 10 CANL*C 2.438,8.5 3.083,8.75 0.646,0.25 10 CANH*C 1.406,7.427 1.719,7.583 0.313,0.156 10 G79 1.073,6.969 1.385,7.125 0.313,0.156 10 *1 1.469,3.698 2.135,3.854 0.667,0.156 10 A 2,3.344 2.646,3.583 0.646,0.24 10 GND1 5.417,3.344 6.063,3.583 0.646,0.24 10 BECU 2.667,1.667 3.333,1.823 0.667,0.156 10 A
*A Main Body ECU (Multiplex Network Body ECU) with 1 Connector *B Main Body ECU (Multiplex Network Body ECU) with 3 Connectors
*C V Bus *D Sub Bus 1
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

C279368
5.385,0.385 5.771,0.656 0.385,0.271 2.26,0.333 2.646,0.604 0.385,0.271 0.073,0.292 0.458,0.563 0.385,0.271 4.938,0.771 5.083,0.771 5.083,0.771 5.281,1.021 true 6.313,0.771 6.458,0.771 6.458,0.771 6.656,1.021 true 0.979,0.948 1.333,1.438 1.333,1.438 1.531,1.438 true 0.927,0.948 1.219,1.625 1.219,1.625 1.417,1.625 true 3.292,0.958 3.646,1.448 3.646,1.448 3.844,1.448 true 3.25,0.969 3.542,1.646 3.542,1.646 3.74,1.646 true 1.448,1.552 2.104,1.771 0.656,0.219 10 CANH*A 3.875,1.354 4.521,1.594 0.646,0.24 10 CANP*B 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 4.271,0.094 4.583,0.25 0.313,0.156 10 *b 3.771,1.563 4.458,1.771 0.688,0.208 10 CANN*B 1.563,1.354 2.156,1.677 0.594,0.323 10 CANL*A 4.542,0.688 5.188,0.927 0.646,0.24 10 GND1 5.917,0.698 6.563,0.938 0.646,0.24 10 BECU 5.531,0.438 5.844,0.594 0.313,0.156 10 A 2.333,0.375 2.74,0.646 0.406,0.271 10 G79 0.146,0.344 0.552,0.615 0.406,0.271 10 G78
*A V Bus *B Sub Bus 1
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])



b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

V Bus
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G78-14 (CANH) - G78-13 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G78-14 (CANH) - A-11 (GND1) Y - None HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G78-13 (CANL) - A-11 (GND1) W - None LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G78-14 (CANH) - A-30 (BECU) Y - None HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G78-13 (CANL) - A-30 (BECU) W - None LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Sub Bus 1
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G79-9 (CANP) - G79-10 (CANN) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G79-9 (CANP) - A-11 (GND1) B - None HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G79-10 (CANN) - A-11 (GND1) W - None LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G79-9 (CANP) - A-30 (BECU) B - None HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G79-10 (CANN) - A-30 (BECU) W - None LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK COMBINATION METER ASSEMBLY


E161130
3.344,0.26 3.823,0.542 0.479,0.281 4.719,1.208 4.885,1.563 4.885,1.563 4.969,1.563 true 2.438,1.229 2.188,1.427 2.188,1.427 2.063,1.427 true 3.375,1.208 3.146,1.646 3.146,1.646 3.021,1.646 true 3.51,1.208 3.698,1.615 3.698,1.615 3.885,1.615 true 3.438,0.323 3.719,0.49 0.281,0.167 10 G16 5.01,1.479 5.271,1.667 0.26,0.188 10 ET 1.906,1.344 2.042,1.531 0.135,0.188 10 B 2.604,1.563 3.021,1.729 0.417,0.167 10 CANH 3.927,1.531 4.354,1.688 0.427,0.156 10 CANL

a.
C240157
1.531,0.146 1.969,0.458 0.438,0.313 1.719,1.219 2.26,1.76 2.26,1.76 2.49,1.76 true 1.635,1.219 1.375,1.844 1.375,1.844 1.135,1.844 true 0.979,1.219 0.781,1.083 0.781,1.083 0.604,1.083 true 2.865,1.448 2.708,1.448 2.708,1.448 2.563,1.229 true 0.073,0.083 0.385,0.24 0.313,0.156 10 *a 1.625,0.229 2.083,0.427 0.458,0.198 10 G16 0.719,1.75 1.177,1.948 0.458,0.198 10 CANH 2.531,1.667 3.01,1.865 0.479,0.198 10 CANL 2.917,1.385 3.219,1.656 0.302,0.271 10 ET 0.49,1.021 0.854,1.281 0.365,0.26 10 B
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G16-32 (CANH) - G16-31 (CANL) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G16-32 (CANH) - G16-21 (ET) G - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G16-31 (CANL) - G16-21 (ET) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G16-32 (CANH) - G16-40 (B) G - Y HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G16-31 (CANL) - G16-40 (B) W - Y LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIRBAG SENSOR ASSEMBLY


C184818
3.177,0.417 3.573,0.677 0.396,0.26 3.656,1.333 3.917,0.729 3.917,0.729 4.135,0.729 true 3.781,1.594 4.021,2.052 4.021,2.052 4.24,2.052 true 2.865,2.115 3.073,2.115 3.073,2.115 3.417,1.594 true 3.24,0.448 3.698,0.646 0.458,0.198 10 G92 4.177,0.625 4.813,0.917 0.635,0.292 10 CANH 4.281,1.948 4.917,2.24 0.635,0.292 10 CANL 2.656,2.021 3.292,2.313 0.635,0.292 10 E1

a.
C227529
0.375,2.521 0.771,2.781 0.396,0.26 0.365,0.948 0.76,1.208 0.396,0.26 2.198,2.896 2.333,3.115 2.333,3.115 2.552,3.115 true 2.115,1.323 2.313,1.677 2.313,1.677 2.552,1.677 true 2.021,1.01 2.438,0.656 2.438,0.656 2.688,0.656 true 1.208,1.677 1.438,1.677 1.438,1.677 1.76,1.323 true 0.177,0.073 0.427,0.271 0.25,0.198 10 *a 0.198,2.083 0.51,2.24 0.313,0.156 10 *b 0.438,2.573 0.781,2.781 0.344,0.208 10 G14 0.417,1 0.76,1.208 0.344,0.208 10 G92 2.75,0.583 3.292,0.792 0.542,0.208 10 CANH 2.604,1.604 3.146,1.813 0.542,0.208 10 CANL 2.604,3.042 3.146,3.25 0.542,0.208 10 BAT 1,1.604 1.542,1.813 0.542,0.208 10 E1
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of DLC3


Disconnect the airbag sensor assembly connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G92-13 (CANH) - G92-22 (CANL) BR - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G92-13 (CANH) - G92-25 (E1) BR - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G92-22 (CANL) - G92-25 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G92-13 (CANH) - G14-16 (BAT) BR - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G92-22 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)


C197053
1.448,0.094 1.865,0.354 0.417,0.26 2.583,0.917 2.75,0.333 2.75,0.333 2.917,0.333 true 2.354,1.594 2.635,1.844 2.635,1.844 2.802,1.844 true 2.354,1.375 1.969,2.042 1.969,2.042 2.229,2.042 true 2.583,0.917 2.75,0.333 2.75,0.333 2.917,0.333 true 0.844,1.49 0.667,1.927 0.667,1.927 0.479,1.927 true 1.521,0.146 1.969,0.458 0.448,0.313 10 A64 2.865,1.75 3.333,1.927 0.469,0.177 10 CANH 2.271,1.958 2.74,2.135 0.469,0.177 10 CANL 2.948,0.26 3.365,0.427 0.417,0.167 10 GND1 0.229,1.844 1.24,2.01 1.01,0.167 10 BM

a.
C234968
1.615,0.135 2.083,0.406 0.469,0.271 2.896,1.99 2.688,1.99 2.688,1.99 2.448,1.354 true 0.729,0.313 0.969,0.313 0.969,0.313 1.458,1.271 true 0.833,2 1.125,2 1.125,2 1.469,1.365 true 0.5,1.531 0.781,1.531 0.781,1.531 1.125,1.115 true 1.729,0.198 2.063,0.427 0.333,0.229 10 A64 0.083,0.073 0.344,0.229 0.26,0.156 10 *a 2.948,1.906 3.219,2.115 0.271,0.208 10 BM 0.094,1.458 0.5,1.625 0.406,0.167 10 GND1 0.406,1.917 0.813,2.083 0.406,0.167 10 CANH 0.323,0.219 0.729,0.385 0.406,0.167 10 CANL
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: for 2 Pin Connector Type

*2: for 22 Pin Connector Type

A64-25 (CANH) - A64-14 (CANL) R - W*1
L - W*2
HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A64-25 (CANH) - A64-1 (GND1) R - W-B*1
L - W-B*2
HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A64-14 (CANL) - A64-1 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A64-25 (CANH) - A64-24 (BM) R - B*1
L - B*2
LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A64-14 (CANL) - A64-24 (BM) W - B LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)


C228050
1.458,0.365 1.885,0.646 0.427,0.281 1.906,1.354 2.188,1.719 2.188,1.719 2.5,1.719 true 1.74,1.354 1.563,1.844 1.563,1.844 1.281,1.844 true 2.125,1.313 2.458,0.99 2.458,0.99 2.771,0.99 true 1.323,1.333 1.021,1.031 1.021,1.031 0.74,1.031 true 1.531,0.427 1.854,0.615 0.323,0.188 10 G12 2.833,0.896 3.24,1.052 0.406,0.156 10 ESS 2.552,1.635 3.052,1.844 0.5,0.208 10 CANL 0.875,1.76 1.375,1.969 0.5,0.208 10 CANH 0.438,0.958 0.938,1.167 0.5,0.208 10 BAT

a.
C277459
1.521,0.188 1.938,0.438 0.417,0.25 1.094,1.844 1.344,1.844 1.344,1.844 1.521,1.396 true 2.563,0.875 2.333,0.875 2.333,0.875 2.115,1.24 true 2.24,1.844 1.99,1.844 1.99,1.844 1.75,1.396 true 0.771,0.906 1.021,0.906 1.021,0.906 1.344,1.219 true 0.083,0.052 0.396,0.208 0.313,0.156 10 false *a 2.625,0.781 3.104,0.938 0.479,0.156 10 false BAT 0.458,0.823 0.938,0.979 0.479,0.156 10 false ESS 1.594,0.219 2.073,0.375 0.479,0.156 10 false G12 2.302,1.75 2.781,1.906 0.479,0.156 10 false CANH 0.688,1.76 1.167,1.917 0.479,0.156 10 false CANL
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G12-3 (CANH) - G12-2 (CANL) P - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G12-3 (CANH) - G12-1 (ESS) P - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G12-2 (CANL) - G12-1 (ESS) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G12-3 (CANH) - G12-5 (BAT) P - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G12-2 (CANL) - G12-5 (BAT) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/Smart Key System)


B264892
4.719,0.646 5.167,0.927 0.448,0.281 1.854,0.646 2.302,0.927 0.448,0.281 3.135,2.323 2.823,2.323 2.823,2.323 2.51,1.646 true 4.281,2.177 4.563,2.177 4.563,2.177 4.823,1.5 true 1.146,0.833 1.344,0.833 1.344,0.833 1.552,1.344 true 4.083,0.906 4.365,0.906 4.365,0.906 4.729,1.479 true 4.813,0.698 5.271,0.896 0.458,0.198 10 G84 3.646,0.823 4.104,1.021 0.458,0.198 10 CANL 3.833,2.094 4.292,2.292 0.458,0.198 10 CANH 0.938,0.771 1.396,0.969 0.458,0.198 10 +B 3.208,2.24 3.667,2.438 0.458,0.198 10 E 1.938,0.708 2.396,0.906 0.458,0.198 10 G82

a.
C277455
0.115,2.396 0.521,2.677 0.406,0.281 0.292,0.677 0.698,0.958 0.406,0.281 0.771,1.406 0.99,1.406 0.99,1.406 1.135,1.083 true 2.292,0.781 2.542,0.552 2.542,0.552 2.75,0.552 true 2.667,1.875 2.427,1.875 2.427,1.875 2.094,2.552 true 2.552,1.604 2.313,1.604 2.313,1.604 1.969,2.542 true 0.052,0.031 0.365,0.188 0.313,0.156 10 *a 0.354,0.74 0.667,0.896 0.313,0.156 10 G82 0.177,2.448 0.49,2.604 0.313,0.156 10 G84 0.615,1.323 0.927,1.479 0.313,0.156 10 E 2.802,0.469 3.115,0.625 0.313,0.156 10 +B 2.719,1.802 3.167,2.031 0.448,0.229 10 CANL 2.604,1.542 3.052,1.771 0.448,0.229 10 CANH
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])


Disconnect the certification ECU (smart key ECU assembly) connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G84-14 (CANH) - G84-15 (CANL) R - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G84-14 (CANH) - G82-11 (E) R - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G84-15 (CANL) - G82-11 (E) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G84-14 (CANH) - G82-2 (+B) R - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G84-15 (CANL) - G82-2 (+B) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Audio and Visual System [for Radio and Display Type])


C297912
4.917,0.094 5.385,0.385 0.469,0.292 1.417,0.125 1.885,0.417 0.469,0.292 0.896,0.469 1.052,0.469 1.052,0.469 1.26,0.698 true 1.729,0.927 1.99,1.292 1.99,1.292 2.156,1.292 true 4.99,0.802 5.292,1.333 5.292,1.333 5.458,1.333 true 4.448,1.375 4.594,1.375 4.594,1.375 4.885,0.802 true 1.479,0.177 2.094,0.375 0.615,0.198 10 false G141 4.979,0.146 5.594,0.344 0.615,0.198 10 false G143 5.5,1.229 6.115,1.427 0.615,0.198 10 false CANH 4.042,1.26 4.656,1.458 0.615,0.198 10 false CANL 2.208,1.188 2.823,1.385 0.615,0.198 10 false GND1 0.594,0.365 1.208,0.563 0.615,0.198 10 false +B1

a.
C277477
1.469,0.26 1.906,0.5 0.438,0.24 1.51,1.844 1.948,2.083 0.438,0.24 2.115,1.49 1.865,1.49 1.865,1.49 1.677,1.156 true 2.625,0.708 2.375,0.708 2.375,0.708 2.177,0.865 true 2.542,3.146 2.292,3.146 2.292,3.146 2.021,2.656 true 1.906,2.656 1.677,3.146 1.677,3.146 1.417,3.146 true 2.156,1.406 2.698,1.635 0.542,0.229 10 false GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 1.51,0.302 1.969,0.5 0.458,0.198 10 false G141 1.542,1.885 2,2.083 0.458,0.198 10 false G143 2.667,0.625 3.208,0.854 0.542,0.229 10 false +B1 2.594,3.063 3.135,3.292 0.542,0.229 10 false CANL 1,3.073 1.542,3.302 0.542,0.229 10 false CANH
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: for 2 Pin Connector Type

*2: for 22 Pin Connector Type

G143-9 (CANH) - G143-10 (CANL) Y - W*1
GR - W*2
HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G143-9 (CANH) - G141-7 (GND1) Y - BR*1
GR - BR*2
HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G143-10 (CANL) - G141-7 (GND1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G143-9 (CANH) - G141-4 (+B1) Y - SB*1
GR - SB*2
HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G143-10 (CANL) - G141-4 (+B1) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)


C297912
4.917,0.094 5.385,0.385 0.469,0.292 1.417,0.125 1.885,0.417 0.469,0.292 0.896,0.469 1.052,0.469 1.052,0.469 1.26,0.698 true 1.729,0.927 1.99,1.292 1.99,1.292 2.156,1.292 true 4.99,0.802 5.292,1.333 5.292,1.333 5.458,1.333 true 4.448,1.375 4.594,1.375 4.594,1.375 4.885,0.802 true 1.479,0.177 2.094,0.375 0.615,0.198 10 false G141 4.979,0.146 5.594,0.344 0.615,0.198 10 false G143 5.5,1.229 6.115,1.427 0.615,0.198 10 false CANH 4.042,1.26 4.656,1.458 0.615,0.198 10 false CANL 2.208,1.188 2.823,1.385 0.615,0.198 10 false GND1 0.594,0.365 1.208,0.563 0.615,0.198 10 false +B1

a.
C277477
1.469,0.26 1.906,0.5 0.438,0.24 1.51,1.844 1.948,2.083 0.438,0.24 2.115,1.49 1.865,1.49 1.865,1.49 1.677,1.156 true 2.625,0.708 2.375,0.708 2.375,0.708 2.177,0.865 true 2.542,3.146 2.292,3.146 2.292,3.146 2.021,2.656 true 1.906,2.656 1.677,3.146 1.677,3.146 1.417,3.146 true 2.156,1.406 2.698,1.635 0.542,0.229 10 false GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 1.51,0.302 1.969,0.5 0.458,0.198 10 false G141 1.542,1.885 2,2.083 0.458,0.198 10 false G143 2.667,0.625 3.208,0.854 0.542,0.229 10 false +B1 2.594,3.063 3.135,3.292 0.542,0.229 10 false CANL 1,3.073 1.542,3.302 0.542,0.229 10 false CANH
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G143-9 (CANH) - G143-10 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G143-9 (CANH) - G141-7 (GND1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G143-10 (CANL) - G141-7 (GND1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G143-9 (CANH) - G141-4 (+B1) Y - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G143-10 (CANL) - G141-4 (+B1) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK 4WD ECU ASSEMBLY (for AWD)


C270073
3.385,0.135 3.813,0.438 0.427,0.302 4.667,1.531 5.146,2.646 5.146,2.646 5.385,2.646 true 4.865,1.531 5.344,2.396 5.344,2.396 5.552,2.396 true 1.677,0.313 1.906,0.313 1.906,0.313 2.427,1.156 true 3.469,0.208 3.938,0.375 0.469,0.167 10 G86 5.594,2.323 6.063,2.49 0.469,0.167 10 CANL 5.438,2.563 5.906,2.729 0.469,0.167 10 CANH 1.344,0.25 1.813,0.417 0.469,0.167 10 GND

a.
C251150
0.417,2.51 0.823,2.792 0.406,0.281 0.438,0.927 0.844,1.208 0.406,0.281 2.208,2.833 2.417,3.021 2.417,3.021 2.594,3.021 true 2.229,1.094 2.438,1.281 2.438,1.281 2.615,1.281 true 2.167,1.094 2.333,1.563 2.333,1.563 2.51,1.563 true 0.875,0.688 1.094,0.688 1.094,0.688 1.229,0.948 true 0.083,0.094 0.396,0.25 0.313,0.156 10 *a 0.104,2.083 0.417,2.24 0.313,0.156 10 *b 0.479,2.563 0.854,2.771 0.375,0.208 10 G14 2.656,2.938 3.031,3.146 0.375,0.208 10 BAT 2.563,1.49 3.042,1.76 0.479,0.271 10 CANH 2.667,1.198 3.146,1.469 0.479,0.271 10 CANL 0.51,0.99 0.885,1.198 0.375,0.208 10 G86 0.552,0.635 1.031,0.906 0.479,0.271 10 GND
*a Rear view of wire harness connector
(to 4WD ECU Assembly)
*b Front view of DLC3


Disconnect the 4WD ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G86-6 (CANH) - G86-5 (CANL) L - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G86-6 (CANH) - G86-4 (GND) L - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G86-5 (CANL) - G86-4 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G86-6 (CANH) - G14-16 (BAT) L - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G86-5 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


a.

for Automatic Air Conditioning System:

C278749
3.375,0.25 3.854,0.542 0.479,0.292 2.417,0.25 2.75,0.25 2.75,0.25 3.375,1.417 true 2.167,0.5 2.5,0.5 2.5,0.5 3.25,1.406 true 4.365,1.521 5.063,2.417 5.063,2.417 5.417,2.417 true 2.083,2.417 2.417,2.417 2.417,2.417 3.083,1.406 true 3.49,0.333 3.948,0.531 0.458,0.198 10 G81 1.771,0.427 2.333,0.667 0.563,0.24 10 CANL 1.75,2.333 2.208,2.531 0.458,0.198 10 GND 2,0.177 2.563,0.417 0.563,0.24 10 CANH 5.479,2.333 5.938,2.531 0.458,0.198 10 B

i.
C240157
0.24,0.969 0.677,1.281 0.438,0.313 1.719,1.115 2.052,0.469 2.052,0.469 2.281,0.469 true 1.635,1.115 1.958,0.219 1.958,0.219 2.188,0.219 true 1.479,1.104 1.219,0.448 1.219,0.448 1,0.448 true 2.99,1.604 2.781,1.604 2.781,1.604 2.563,1.229 true 0.073,0.083 0.385,0.24 0.313,0.156 10 *a 0.333,1.052 0.792,1.25 0.458,0.198 10 G81 2.333,0.406 2.792,0.604 0.458,0.198 10 CANH 2.25,0.156 2.708,0.354 0.458,0.198 10 CANL 3.031,1.531 3.333,1.802 0.302,0.271 10 B 0.667,0.385 1.031,0.646 0.365,0.26 10 GND
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G81-11 (CANH) - G81-12 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G81-11 (CANH) - G81-14 (GND) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G81-12 (CANL) - G81-14 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G81-11 (CANH) - G81-21 (B) B - GR HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G81-12 (CANL) - G81-21 (B) W - GR LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



b.

for Manual Air Conditioning System:

E219842
3.396,0.208 3.813,0.469 0.417,0.26 1.969,0.438 2.198,0.438 2.198,0.438 2.615,0.865 true 2.333,0.229 2.563,0.229 2.563,0.229 2.76,0.844 true 2.229,1.354 2.396,1.354 2.396,1.354 2.698,1.031 true 3.469,0.26 3.927,0.458 0.458,0.198 10 G80 1.896,0.146 2.375,0.344 0.479,0.198 10 CANH 1.573,0.354 2.052,0.552 0.479,0.198 10 CANL 1.896,1.271 2.375,1.469 0.479,0.198 10 GND

i.
C279367
1.479,0.167 1.906,0.406 0.427,0.24 0.385,2.563 0.813,2.802 0.427,0.24 2.594,3.073 2.396,3.073 2.396,3.073 2.208,2.813 true 1.094,1.021 0.896,0.76 0.896,0.76 0.708,0.76 true 1.177,1.01 0.969,0.49 0.969,0.49 0.781,0.49 true 1.135,1.135 0.927,1.5 0.927,1.5 0.74,1.5 true 0.073,0.052 0.385,0.208 0.313,0.156 10 *a 0.115,1.948 0.427,2.104 0.313,0.156 10 *b 0.458,2.594 0.854,2.813 0.396,0.219 10 G14 1.552,0.208 1.948,0.427 0.396,0.219 10 G80 2.656,2.99 3.052,3.208 0.396,0.219 10 BAT 0.396,1.406 0.792,1.625 0.396,0.219 10 GND 0.333,0.677 0.802,0.896 0.469,0.219 10 CANL 0.365,0.406 0.833,0.625 0.469,0.219 10 CANH
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of DLC3


Disconnect the air conditioning amplifier assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: for 2 Pin Connector Type

*2: for 22 Pin Connector Type

G80-8 (CANH) - G80-9 (CANL) B - W*1
V - W*2
HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G80-8 (CANH) - G80-23 (GND) B - W-B*1
V - W-B*2
HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G80-9 (CANL) - G80-23 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G80-8 (CANH) - G14-16 (BAT) B - L*1
V - L*2
HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G80-9 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CHECK POWER STEERING ECU ASSEMBLY


C239855
3.781,1.781 4.188,2.021 0.406,0.24 3.656,0.271 4.063,0.51 0.406,0.24 1.854,0.896 2.188,1.094 0.333,0.198 0.896,1.323 1.229,1.521 0.333,0.198 2.021,0.896 2.021,0.781 false 1.042,1.313 1.042,1.135 true 3.385,2.406 3.594,2.406 3.594,2.406 3.823,2.573 true 3.406,3.125 3.615,3.125 3.615,3.125 3.844,2.729 true 3.156,1.563 3.375,1.563 3.375,1.563 3.563,1.052 true 4.698,1.521 4.438,1.521 4.438,1.521 4.198,1.052 true 0.969,1.344 1.281,1.542 0.313,0.198 10 h1 1.938,0.917 2.25,1.115 0.313,0.198 10 h2 3.771,0.313 4.083,0.51 0.313,0.198 10 h2 3.917,1.833 4.229,2.031 0.313,0.198 10 h1 2.948,2.344 3.5,2.521 0.552,0.177 10 CANH 2.979,3.052 3.531,3.229 0.552,0.177 10 CANL 2.729,1.49 3.281,1.667 0.552,0.177 10 PGND 4.75,1.448 5.302,1.625 0.552,0.177 10 PIG

a.
C279366
0.354,2.479 0.719,2.74 0.365,0.26 0.458,0.969 0.823,1.229 0.365,0.26 1.969,0.938 2.25,0.74 2.25,0.74 2.469,0.74 true 1.969,1.25 2.208,1.521 2.208,1.521 2.427,1.521 true 2.156,2.615 2.438,2.417 2.438,2.417 2.656,2.417 true 0.844,2.271 1.094,2.271 1.094,2.271 1.323,2.542 true 0.094,0.073 0.406,0.229 0.313,0.156 10 *a 0.563,1.01 0.875,1.167 0.313,0.156 10 h1 0.469,2.531 0.781,2.688 0.313,0.156 10 h2 2.521,0.646 3.01,0.854 0.49,0.208 10 CANH 2.469,1.427 2.958,1.635 0.49,0.208 10 CANL 2.708,2.333 3.198,2.542 0.49,0.208 10 PGND 0.573,2.188 1.063,2.396 0.49,0.208 10 PIG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the power steering ECU assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
h1-4 (CANH) - h1-8 (CANL) W - B HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
h1-4 (CANH) - h2-2 (PGND) W - B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
h1-8 (CANL) - h2-2 (PGND) B - B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
h1-4 (CANH) - h2-1 (PIG) W - R HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
h1-8 (CANL) - h2-1 (PIG) B - R LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)


C270135
1.479,0.177 1.875,0.438 0.396,0.26 2.604,0.583 2.417,0.583 2.417,0.583 2.146,1.01 true 2.479,0.375 2.24,0.375 2.24,0.375 1.948,1 true 1.281,1.354 0.917,1.844 0.917,1.844 0.729,1.844 true 2.531,1.688 2.344,1.688 2.344,1.688 2.198,1.333 true 2.344,1.927 2.135,1.927 2.135,1.927 1.938,1.333 true 1.594,0.219 1.906,0.417 0.313,0.198 10 R1 2.635,0.5 3.24,0.813 0.604,0.313 10 CA2P*B 2.521,0.302 3.125,0.615 0.604,0.313 10 CA1P*A 2.625,1.625 3.229,1.938 0.604,0.313 10 CA2N*B 2.375,1.865 3.042,2.125 0.667,0.26 10 CA1N*A 0.333,1.76 0.938,2.073 0.604,0.313 10 BLGD
*A V Bus
*B Sensor Bus


a.
C268298
1.531,1.948 1.948,2.208 0.417,0.26 1.469,0.24 1.885,0.5 0.417,0.26 1.448,1.063 1.188,0.719 1.188,0.719 0.958,0.719 true 1.458,1.188 1.198,1.531 1.198,1.531 0.969,1.531 true 2.198,2.938 2.292,3.219 2.292,3.219 2.542,3.219 true 1.583,1.208 1.344,1.813 1.344,1.813 1.115,1.813 true 1.563,1.063 1.219,0.448 1.219,0.448 0.99,0.448 true 1.927,1.198 2.135,1.604 2.135,1.604 2.385,1.604 true 0.073,0.083 0.385,0.24 0.313,0.156 10 *a 0.104,1.979 0.417,2.135 0.313,0.156 10 *b 0.427,0.646 1.042,0.927 0.615,0.281 10 CA2P*B 0.594,1.74 1.208,1.948 0.615,0.208 10 CA1N*A 2.573,3.156 3.063,3.354 0.49,0.198 10 BAT 1.573,0.292 1.969,0.469 0.396,0.177 10 R1 1.604,2 2,2.177 0.396,0.177 10 G14 0.438,0.396 1.052,0.677 0.615,0.281 10 CA1P*A 0.417,1.458 1.042,1.75 0.625,0.292 10 CA2N*B 2.448,1.51 2.938,1.708 0.49,0.198 10 BLGD
*A V Bus
*B Sensor Bus
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
*b Front view of DLC3


Disconnect the blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

V Bus
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R1-2 (CA1P) - R1-7 (CA1N) R - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
R1-2 (CA1P) - R1-10 (BLGD) R - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
R1-7 (CA1N) - R1-10 (BLGD) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
R1-2 (CA1P) - G14-16 (BAT) R - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R1-7 (CA1N) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Sensor Bus
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R1-1 (CA2P) - R1-6 (CA2N) W - B HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
R1-1 (CA2P) - R1-10 (BLGD) W - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
R1-6 (CA2N) - R1-10 (BLGD) B - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
R1-1 (CA2P) - G14-16 (BAT) W - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R1-6 (CA2N) - G14-16 (BAT) B - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BLIND SPOT MONITOR SENSOR RH (w/ Blind Spot Monitor System)


C270135
1.479,0.177 1.875,0.438 0.396,0.26 2.604,0.583 2.417,0.583 2.417,0.583 2.146,1.01 true 1.281,1.354 0.917,1.844 0.917,1.844 0.729,1.844 true 2.531,1.688 2.344,1.688 2.344,1.688 2.198,1.333 true 1.604,0.219 1.917,0.417 0.313,0.198 10 T1 2.635,0.5 3.24,0.813 0.604,0.313 10 CA2P 2.625,1.625 3.229,1.938 0.604,0.313 10 CA2N 0.333,1.76 0.938,2.073 0.604,0.313 10 BRGB

a.
C268298
1.531,1.948 1.948,2.208 0.417,0.26 1.469,0.24 1.885,0.5 0.417,0.26 2.198,2.938 2.292,3.219 2.292,3.219 2.542,3.219 true 1.438,1.219 1.281,1.635 1.281,1.635 1.052,1.635 true 1.438,1.063 1.156,0.646 1.156,0.646 0.938,0.646 true 1.927,1.198 2.135,1.604 2.135,1.604 2.385,1.604 true 0.073,0.083 0.385,0.24 0.313,0.156 10 *a 0.104,1.979 0.417,2.135 0.313,0.156 10 *b 2.573,3.156 3.063,3.354 0.49,0.198 10 BAT 1.573,0.292 1.969,0.469 0.396,0.177 10 T1 1.604,2 2,2.177 0.396,0.177 10 G14 0.563,0.573 1.177,0.854 0.615,0.281 10 CA2P 0.667,1.552 1.292,1.844 0.625,0.292 10 CA2N 2.448,1.51 2.938,1.708 0.49,0.198 10 BRGB
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)
*b Front view of DLC3


Disconnect the blind spot monitor sensor RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
T1-1 (CA2P) - T1-6 (CA2N) W - B HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
T1-1 (CA2P) - T1-10 (BRGB) W - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
T1-6 (CA2N) - T1-10 (BRGB) B - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
T1-1 (CA2P) - G14-16 (BAT) W - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
T1-6 (CA2N) - G14-16 (BAT) B - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK LANE DEPARTURE WARNING CAMERA (w/ Lane Departure Alert System)


C279365
1.5,0.26 1.927,0.542 0.427,0.281 0.802,0.771 0.938,0.771 0.938,0.771 1.229,1.167 true 0.875,1.885 1.021,1.885 1.021,1.885 1.24,1.531 true 1.448,1.563 1.667,1.927 1.667,1.927 1.833,1.927 true 1.583,0.313 2.042,0.51 0.458,0.198 10 Q13 0.417,0.708 0.875,0.906 0.458,0.198 10 CA1P 0.448,1.792 0.906,1.99 0.458,0.198 10 CA1N 1.865,1.854 2.323,2.052 0.458,0.198 10 GND

a.
C267485
0.563,1.063 0.99,1.344 0.427,0.281 0.396,2.542 0.823,2.823 0.427,0.281 2.198,2.917 2.344,3.125 2.344,3.125 2.563,3.125 true 2.073,1.406 2.219,1.615 2.219,1.615 2.438,1.615 true 2.063,1.135 2.208,0.958 2.208,0.958 2.427,0.958 true 1.927,1.406 2.208,1.896 2.208,1.896 2.427,1.896 true 0.083,0.083 0.396,0.25 0.313,0.167 10 *a 0.167,2.094 0.479,2.25 0.313,0.156 10 *b 2.615,3.052 2.969,3.24 0.354,0.188 10 BAT 0.469,2.615 0.823,2.802 0.354,0.188 10 G14 0.635,1.115 0.99,1.302 0.354,0.188 10 Q13 2.5,1.531 2.969,1.719 0.469,0.188 10 CA1N 2.5,0.885 2.969,1.073 0.469,0.188 10 CA1P 2.469,1.813 2.938,2 0.469,0.188 10 GND
*a Front view of wire harness connector
(to Lane Departure Warning Camera)
*b Front view of DLC3


Disconnect the lane departure warning camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q13-6 (CA1P) - Q13-12 (CA1N) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
Q13-6 (CA1P) - Q13-11 (GND) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q13-12 (CA1N) - Q13-11 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q13-6 (CA1P) - G14-16 (BAT) B - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Q13-12 (CA1N) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door System)


C278778
2.417,0.531 2.833,0.781 0.417,0.25 4.302,0.51 4.719,0.76 0.417,0.25 5.635,2.094 5.448,2.094 5.448,2.094 5.094,1.615 true 5.479,2.354 5.292,2.354 5.292,2.354 5.042,1.594 true 3.219,2.094 3,2.094 3,2.094 2.646,1.51 true 2.125,2.094 2.344,2.094 2.344,2.094 2.542,1.5 true 2.5,0.583 2.958,0.781 0.458,0.198 10 U19 4.375,0.552 4.833,0.75 0.458,0.198 10 U18 5.688,2.031 6.146,2.229 0.458,0.198 10 CANP 5.531,2.281 5.99,2.479 0.458,0.198 10 CANN 3.271,2.021 3.729,2.219 0.458,0.198 10 GND 1.958,2.021 2.417,2.219 0.458,0.198 10 B

a.
C278775
0.542,2.375 0.938,2.625 0.396,0.25 0.375,0.885 0.771,1.135 0.396,0.25 2.333,1.063 2.448,1.25 2.448,1.25 2.615,1.25 true 2.229,1.063 2.385,1.479 2.385,1.479 2.604,1.479 true 1.667,2.583 1.417,3 1.417,3 1.25,3 true 1.833,2.583 2.021,2.917 2.021,2.917 2.188,2.917 true 0.094,0.073 0.406,0.229 0.313,0.156 10 *a 0.448,0.927 0.802,1.135 0.354,0.208 10 U18 0.615,2.417 0.969,2.625 0.354,0.208 10 U19 2.656,1.417 3.115,1.677 0.458,0.26 10 CANN 2.677,1.167 3.198,1.417 0.521,0.25 10 CANP 2.25,2.833 2.771,3.083 0.521,0.25 10 GND 1.135,2.917 1.656,3.167 0.521,0.25 10 B
*a Rear view of wire harness connector
(to Multiplex Network Door ECU)


Disconnect the multiplex network door ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
U18-13 (CANP) - U18-14 (CANN) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
U18-13 (CANP) - U19-7 (GND) G - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
U18-14 (CANN) - U19-7 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
U18-13 (CANP) - U19-8 (B) G - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
U18-14 (CANN) - U19-8 (B) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (w/ Seat Memory)


B219506
4.74,0.833 5.115,1.063 0.375,0.229 1.938,0.958 2.313,1.188 0.375,0.229 5.042,1.427 4.844,1.427 4.844,1.427 4.427,1.219 true 4.927,1.625 4.729,1.625 4.729,1.625 4.354,1.208 true 3.708,0.531 3.458,0.531 3.458,0.531 3.552,0.917 true 3.469,0.208 3.271,0.208 3.271,0.208 3.531,1.115 true 4.844,0.865 5.156,1.063 0.313,0.198 10 false e6 2,1 2.313,1.198 0.313,0.198 10 false e18 4.969,1.521 5.583,1.719 0.615,0.198 10 false CANP 5.083,1.323 5.698,1.521 0.615,0.198 10 false CANN 3.76,0.427 4.375,0.625 0.615,0.198 10 false GND1 3.51,0.125 4.125,0.323 0.615,0.198 10 false +B1

a.
C219234
0.208,1.208 0.625,1.479 0.417,0.271 2.74,0.948 3.135,1.208 0.396,0.26 2.802,1.656 2.667,1.656 2.667,1.656 2.542,1.573 true 2.656,1.917 2.521,1.917 2.521,1.917 2.438,1.563 true 1.375,1.25 0.99,0.823 0.99,0.823 0.781,0.823 true 0.885,1.833 1.052,1.833 1.052,1.833 1.375,1.396 true 0.104,0.073 0.594,0.49 0.49,0.417 10 false *a 0.302,1.271 0.677,1.521 0.375,0.25 10 false e18 2.844,0.99 3.177,1.208 0.333,0.219 10 false e6 2.854,1.573 3.292,1.771 0.438,0.198 10 false CANN 2.708,1.833 3.188,2.021 0.479,0.188 10 false CANP 0.594,1.74 1.031,1.938 0.438,0.198 10 false +B1 0.375,0.74 0.813,0.938 0.438,0.198 10 false GND1
*a Rear view of wire harness connector
(to Position Control ECU and Switch Assembly)


Disconnect the position control ECU assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
e6-8 (CANP) - e6-7 (CANN) L - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
e6-8 (CANP) - e18-2 (GND1) L - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
e6-7 (CANN) - e18-2 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
e6-8 (CANP) - e18-7 (+B1) L - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
e6-7 (CANN) - e18-7 (+B1) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BATTERY CURRENT SENSOR ASSEMBLY (for 2WD)


C270135
1.479,0.177 1.875,0.438 0.396,0.26 2.417,0.583 2.229,0.583 2.229,0.583 1.958,1.01 true 1.656,1.021 1.073,0.625 1.073,0.625 0.885,0.625 true 1.563,0.219 1.875,0.417 0.313,0.198 10 A58 2.479,0.5 3.083,0.813 0.604,0.313 10 CA3N 0.5,0.563 1.104,0.875 0.604,0.313 10 CA3P

a.
C268298
1.531,1.948 1.948,2.208 0.417,0.26 1.469,0.24 1.885,0.5 0.417,0.26 2.198,2.938 2.292,3.219 2.292,3.219 2.542,3.219 true 1.677,1.052 1.219,0.479 1.219,0.479 0.969,0.479 true 1.573,1.042 1.198,0.854 1.198,0.854 0.979,0.854 true 1.073,2.167 1.323,2.167 1.323,2.167 1.646,2.521 true 0.073,0.083 0.385,0.24 0.313,0.156 10 *a 0.104,1.979 0.417,2.135 0.313,0.156 10 *b 2.573,3.156 3.063,3.354 0.49,0.198 10 BAT 1.542,0.292 1.938,0.469 0.396,0.177 10 A58 1.604,2 2,2.177 0.396,0.177 10 G14 0.542,0.802 1.156,1.083 0.615,0.281 10 CA3N 0.573,0.417 1.198,0.708 0.625,0.292 10 CA3P 0.781,2.083 1.271,2.281 0.49,0.198 10 CG
*a Front view of wire harness connector
(to Battery Current Sensor Assembly)
*b Front view of DLC3


Disconnect the battery current sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A58-3 (CA3P) - A58-2 (CA3N) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A58-3 (CA3P) - G14-4 (CG) B - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A58-2 (CA3N) - G14-4 (CG) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A58-3 (CA3P) - G14-16 (BAT) B - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A58-2 (CA3N) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher