Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2013.11
RM30B0U _57 Power Source / Network _009133 NETWORKING _0050933 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Navigation ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Navigation ECU Communication Stop Mode Either condition is met:
·

"Display and Navigation (AVN1)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Navigation ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside navigation receiver assembly

·

Navigation receiver assembly CAN branch wire or connector

·

Navigation receiver assembly



For vehicles with a navigation system.


WIRING DIAGRAM

C280381
5.063,6 6.927,6.344 1.865,0.344 10 false Navigation Receiver Assembly 5.646,5.073 7,5.458 1.354,0.385 10 false GND1 5.646,4.25 7,4.635 1.354,0.385 10 false ACC1 5.646,3.438 7,3.823 1.354,0.385 10 false IG 5.646,2.583 7,2.969 1.354,0.385 10 false +B1 5.646,1.438 7,1.823 1.354,0.385 10 false CANL 5.656,0.833 7.01,1.219 1.354,0.385 10 false CANH 1.677,0.698 3.031,1.083 1.354,0.385 10 false 1 1.667,1.292 3.021,1.677 1.354,0.385 10 false 2 0.229,1.75 1.583,2.135 1.354,0.385 10 false G130 0.229,1.906 2.604,2.188 2.375,0.281 10 false No. 2 CAN Junction Connector 2.115,2.594 3.469,2.979 1.354,0.385 10 false from Battery 1.604,3.417 2.958,3.802 1.354,0.385 10 false from IG1 NO.1 Relay 1.865,4.24 3.219,4.625 1.354,0.385 10 false from ACC Relay 4.135,4.063 5.49,4.448 1.354,0.385 10 false ACC 3.906,3.25 5.26,3.635 1.354,0.385 10 false ECU-IG NO.2 4.073,2.417 4.99,2.833 0.917,0.417 10 false RADIO 5.104,2.594 6.021,3.01 0.917,0.417 10 false G141 5.104,3.427 6.021,3.844 0.917,0.417 10 false G143 5.115,4.24 6.031,4.656 0.917,0.417 10 false G141 5.115,5.052 6.031,5.469 0.917,0.417 10 false G141 5.104,1.417 6.021,1.833 0.917,0.417 10 false G143 5.115,0.823 6.031,1.24 0.917,0.417 10 false G143 5.188,1.146 6.542,1.531 1.354,0.385 10 false 10 5.24,0.563 6.594,0.948 1.354,0.385 10 false 9 5.229,2.323 6.583,2.708 1.354,0.385 10 false 4 5.219,3.167 6.573,3.552 1.354,0.385 10 false 1 5.219,3.99 6.573,4.375 1.354,0.385 10 false 3 5.229,4.781 6.583,5.167 1.354,0.385 10 false 7

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY CAN BRANCH WIRE)
a.
E140414
1.469,0.417 1.969,0.698 0.5,0.281 2.083,1.469 2.25,2 2.25,2 2.5,2 true 1.938,1.469 1.833,2 1.833,2 1.667,2 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 2.552,1.906 3.167,2.104 0.615,0.198 10 CANL 1.24,1.917 1.854,2.115 0.615,0.198 10 CANH 1.542,0.469 2,0.667 0.458,0.198 10 G143
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-9 (CANH) - G143-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE NAVIGATION RECEIVER ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C277477
1.5,0.208 1.938,0.448 0.438,0.24 1.542,1.813 1.979,2.052 0.438,0.24 0.979,2.604 0.802,2.396 0.802,2.396 0.635,2.396 true 2.104,1.479 1.854,1.479 1.854,1.479 1.667,1.146 true 2.573,0.708 2.375,0.708 2.375,0.708 2.198,0.896 true 2.438,0.396 2.24,0.396 2.24,0.396 2,0.885 true 0.448,2.302 0.906,2.5 0.458,0.198 10 IG 2.146,1.396 2.688,1.625 0.542,0.229 10 GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 *a 1.542,0.25 2,0.448 0.458,0.198 10 G141 1.583,1.854 2.042,2.052 0.458,0.198 10 G143 2.615,0.604 3.156,0.833 0.542,0.229 10 +B1 2.469,0.292 3.01,0.521 0.542,0.229 10 ACC1
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Disconnect the navigation receiver assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G141-4 (+B1) - Body ground Always 11 to 14 V
G143-1 (IG) - Body ground Ignition switch ON 11 to 14 V
G141-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G141-7 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR