Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2013.11
RM30B0U _56 Audio / Visual / Telematics _009009 NAVIGATION / MULTI INFO DISPLAY _0104226 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  AVC-LAN Circuit  


DESCRIPTION

Each unit of the navigation system connected to the AVC-LAN (communication bus) transfers the switch signals using the AVC-LAN.

If a short to +B or short to ground occurs in the AVC-LAN, the navigation system will not function normally because communication is not possible.

WIRING DIAGRAM

E280962
2.469,0.438 2.625,0.635 0.156,0.198 10 false 8 2.49,1.229 2.646,1.427 0.156,0.198 10 false 7 5.635,0.406 5.792,0.604 0.156,0.198 10 false 7 5.667,1.188 5.823,1.385 0.156,0.198 10 false 8 2.094,0.552 2.396,0.75 0.302,0.198 10 false TX+ 2.073,1.365 2.375,1.563 0.302,0.198 10 false TX- 5.865,1.385 6.365,1.625 0.5,0.24 10 false TX1- 5.865,0.573 6.49,0.813 0.625,0.24 10 false TX1+ 5.74,1.917 6.24,2.156 0.5,0.24 10 false G143 5.75,2.115 7.042,2.49 1.292,0.375 10 false Navigation Receiver Assembly 1.198,1.896 1.698,2.135 0.5,0.24 10 false M22 1.219,2.063 3.625,2.271 2.406,0.208 10 false Stereo Component Amplifier Assembly 0.875,2.385 3.281,2.594 2.406,0.208 10 false : AVC-LAN communication Line

CAUTION / NOTICE / HINT

HINT:

The navigation receiver assembly is the master unit.


NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.
E280968
1.74,0.958 1.229,0.406 1.229,0.406 1.031,0.406 true 1.906,0.958 2.594,0.448 2.594,0.448 2.771,0.448 true 0.708,0.313 1.125,0.49 0.417,0.177 10 false TX1- 2.833,0.354 3.25,0.531 0.417,0.177 10 false TX1+

Remove the navigation receiver assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (TX1+) - 8 (TX1-) Always 60 to 80 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
a.

Disconnect the G143 navigation receiver assembly connector.


b.

Disconnect the M22 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M22-8 (TX+) - G143-7 (TX1+) Always Below 1 Ω
M22-7 (TX-) - G143-8 (TX1-) Always Below 1 Ω
M22-8 (TX+) - Body ground Always 10 kΩ or higher
M22-7 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal operation.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal operation, the slave unit is defective and should be replaced.



OK:

Master unit returns to normal operation.



Result:
Proceed to
OK
NG



OK

REPLACE MALFUNCTIONING PARTS

NG