Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2013.11
RM30B0U _56 Audio / Visual / Telematics _009009 NAVIGATION / MULTI INFO DISPLAY _0104226 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Navigation Receiver Assembly Power Source Circuit  


DESCRIPTION

This circuit provides power to the navigation receiver assembly.

WIRING DIAGRAM

E282609
1.031,0.344 1.865,0.542 0.833,0.198 10 false from Battery 0.5,0.813 1.875,1 1.375,0.188 10 false from IG1 NO. 1 Relay 0.802,1.302 1.906,1.5 1.104,0.198 10 false from ACC Relay 3.146,0.521 3.917,0.698 0.771,0.177 10 false RADIO 2.917,0.969 4.302,1.198 1.385,0.229 10 false ECU-IG NO.2 3.198,1.5 3.969,1.677 0.771,0.177 10 false ACC 5.313,0.375 5.76,0.552 0.448,0.177 10 false G141 5.302,0.833 5.75,1.01 0.448,0.177 10 false G143 5.302,1.313 5.75,1.49 0.448,0.177 10 false G141 5.302,1.76 5.75,1.938 0.448,0.177 10 false G141 5.417,0.156 5.563,0.354 0.146,0.198 10 false 4 5.406,0.615 5.552,0.813 0.146,0.198 10 false 1 5.427,1.104 5.573,1.302 0.146,0.198 10 false 3 5.427,1.542 5.573,1.74 0.146,0.198 10 false 7 5.729,1.781 6.177,1.958 0.448,0.177 10 false GND1 5.729,1.323 6.177,1.5 0.448,0.177 10 false ACC1 5.719,0.844 6.167,1.021 0.448,0.177 10 false IG 5.708,0.385 6.156,0.563 0.448,0.177 10 false +B1 5.521,2.156 6.802,2.51 1.281,0.354 10 false Navigation Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E280967
0.458,0.833 0.833,1.052 0.375,0.219 0.375,2.448 0.75,2.667 0.375,0.219 0.688,2.917 0.844,2.917 0.844,2.917 1.083,2.563 true 1.208,1.417 1.365,1.417 1.365,1.417 1.604,1.063 true 2.406,0.375 2.229,0.375 2.229,0.375 1.927,0.75 true 2.521,1.021 2.333,1.021 2.333,1.021 2.135,0.865 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.479,0.854 0.979,1.125 0.5,0.271 10 false G141 0.396,2.469 0.802,2.708 0.406,0.24 10 false G143 0.823,1.333 1.406,1.563 0.583,0.229 10 false GND1 2.458,0.313 3.021,0.531 0.563,0.219 10 false ACC1 2.563,0.948 3.125,1.167 0.563,0.219 10 false +B1 0.51,2.833 0.865,3.042 0.354,0.208 10 false IG
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G141-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G141-4 (+B1) - Body ground Always 11 to 14 V
G141-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
G143-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR