Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2013.11
RM30B0U _56 Audio / Visual / Telematics _009009 NAVIGATION / MULTI INFO DISPLAY _0104226 NAVIGATION SYSTEM T

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  PROBLEM SYMPTOMS TABLE  


NOTICE:

After replacing the stereo component tuner assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary (w/ SDARS System).


HINT:
·

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.

·

Inspect the fuses and relays related to this system before inspecting the suspected areas below.



Display Function
Symptom Suspected Area Link
Pressing ignition switch does not turn on system Proceed to "Navigation Receiver Assembly Power Source Circuit" Click here
Navigation receiver assembly Click here
Black screen (No image appears on navigation/audio screen) Proceed to "Black Screen" Click here
Navigation receiver assembly Click here
Display does not dim (does not change to night screen) with tail switch on Proceed to "Display does not Dim when Light Control Switch is Turned ON" Click here
Proceed to "Illumination Circuit" Click here
Navigation receiver assembly Click here
Power does not turn off (Screen remains on) Proceed to "Navigation Receiver Assembly Power Source Circuit" Click here
Navigation receiver assembly Click here
Screen is distorted Proceed to "Navigation Receiver Assembly Power Source Circuit" Click here
Navigation receiver assembly Click here
Screen flicker or color distortion Proceed to "Screen Flicker or Color Distortion" Click here
Proceed to "Navigation Receiver Assembly Power Source Circuit" Click here
Navigation receiver assembly Click here
Navigation function switches can be operated while vehicle being driven Proceed to "Parking Brake Switch Circuit" Click here
Navigation receiver assembly Click here

Panel Switch and Touch Switch Function
Symptom Suspected Area Link
Illumination for panel switches does not come on with tail switch on Proceed to "Illumination for Panel Switch does not Come on with Tail Switch ON" Click here
Proceed to "Illumination Circuit" Click here
Navigation receiver assembly Click here
Panel switches do not function Proceed to "Panel Switches do not Function" Click here
Proceed to "Navigation Receiver Assembly Power Source Circuit" Click here
Navigation receiver assembly Click here
Touch panel switch does not function Proceed to "Touch Panel Switch does not Function" Click here
Proceed to "Navigation Receiver Assembly Power Source Circuit" Click here
Navigation receiver assembly Click here
Navigation function switches can be operated while vehicle is driving Proceed to "Parking Brake Switch Circuit" Click here
Navigation receiver assembly Click here

Steering Pad Switch Function
Symptom Suspected Area Link
System cannot be operated by steering pad switch Proceed to "Panel Switches do not Function" Click here
Proceed to "Steering Pad Switch Circuit" Click here
Navigation receiver assembly Click here
Illumination for steering pad switch does not come on with tail switch on Proceed to "Illumination Circuit" Click here
Navigation receiver assembly Click here

Navigation Function
Symptom Suspected Area Link
GPS mark is not displayed Proceed to "GPS Mark is not Displayed" Click here
Navigation antenna assembly Click here
Navigation receiver assembly Click here
Date and time on navigation screen is different from actual date and time Proceed to "GPS Mark is not Displayed" Click here
Navigation antenna assembly Click here
Navigation receiver assembly Click here
Vehicle position mark deviates from correct position and does not return to correct position Proceed to "GPS Mark is not Displayed" Click here
Navigation antenna assembly Click here
Navigation receiver assembly Click here
Cursor or map rotates when vehicle is stopped Proceed to "Cursor or Map Rotates when Vehicle Stopped" Click here
Navigation receiver assembly Click here
Vehicle position mark moves in the opposite direction to the vehicle Proceed to "Cursor or Map Rotates when Vehicle Stopped" Click here
Proceed to "Reverse Signal Circuit" Click here
Navigation receiver assembly Click here
Vehicle position mark deviates from and returns to correct position repeatedly even though GPS mark is displayed Proceed to "GPS Mark is not Displayed" Click here
Drive the vehicle for sensor learning (At a place where GPS signals can be received, drive the vehicle clockwise and counterclockwise in at least a 200 meter square 2 times or more) -
Navigation antenna assembly Click here
Navigation receiver assembly Click here
Vehicle position mark moves slow or fast Proceed to "GPS Mark is not Displayed" Click here
Navigation antenna assembly Click here
Navigation receiver assembly Click here
Voice guidance does not function Proceed to "Voice Guidance does not Function" Click here
Proceed to "Mute Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier"* Click here
Proceed to "Navigation Voice Circuit"* Click here
Proceed to "Speaker Circuit" Click here
Navigation receiver assembly Click here
Map display is incomplete SD card -
Navigation receiver assembly Click here
Route cannot be calculated Proceed to "Route cannot be Calculated" Click here
Navigation receiver assembly Click here
Navigation system cannot record memory point registration or each item setting Navigation receiver assembly Click here
A message indicating to wait for a while because of low temperature is displayed Start the engine and increase cabin temperature (Near navigation receiver assembly) -
Navigation receiver assembly Click here
A message is displayed because map data cannot be read, and current position screen is not displayed If message appears only when driving on rough roads, check if message disappears when vehicle is stopped -
SD card -
Navigation receiver assembly Click here
Map screen turns white or blue (GPS receiving status is displayed normally, and switches and own vehicle position mark are also displayed normally) Change map scale to smallest (a scale that shows a large area) -
SD card -
Navigation receiver assembly Click here
Traffic information is not displayed Proceed to "Traffic Information is not Displayed" Click here
Customizable parameters cannot be changed (customizable parameters can be changed by using the Techstream) Navigation receiver assembly Click here
Reverse signal does not change in vehicle signal check mode Proceed to "Reverse Signal Circuit" Click here
Navigation receiver assembly Click here
Parking brake switch signal does not change in vehicle signal check mode Proceed to "Parking Brake Switch Circuit" Click here
Navigation receiver assembly Click here

*: for 11 Speakers


General Audio Function
Symptom Suspected Area Link
No sound can be heard from speakers Proceed to "No Sound can be Heard from Speakers" Click here
Proceed to "Mute Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier"* Click here
Proceed to "Speaker circuit" Click here
Proceed to "Sound Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier" Click here
Proceed to "Stereo Component Amplifier Power Source Circuit" Click here
Stereo component amplifier assembly Click here
Navigation receiver assembly Click here
Abnormal noise occurs Proceed to "Noise Occurs" Click here
Stereo component amplifier assembly Click here
Navigation receiver assembly Click here
Sound quality is bad in all modes. (Volume is too low) Check that the ASL function is off. -
Proceed to "Poor Sound Quality in All Modes (Low Volume)" Click here
Proceed to "Mute Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier"* Click here
Proceed to "Speaker circuit" Click here
Proceed to "Sound Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier" Click here
Stereo component amplifier assembly Click here
Navigation receiver assembly Click here
ASL does not function Check that the ASL function is on. -
Proceed to "Vehicle Speed Signal Circuit between Navigation Receiver Assembly and Combination Meter" Click here
Proceed to "Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter"* Click here
Stereo component amplifier assembly Click here
Navigation receiver assembly Click here

*: for 11 Speakers


FM or AM Radio Function
Symptom Suspected Area Link
Radio broadcast cannot be received or poor reception Proceed to "Radio Broadcast cannot be Received or Poor Reception" Click here
Radio broadcast can be received but radio station cannot be displayed (Some radio stations do not provide their name information) Navigation receiver assembly Click here
Radio broadcast can be displayed but radio broadcast cannot be heard from speakers Check the volume settings -
Navigation receiver assembly Click here
Radio broadcast can be received but station list cannot be displayed Wait for 120 seconds in radio mode, and select the "Refresh" switch on the station list screen -
Navigation receiver assembly Click here
Radio broadcast can be received but station list cannot be displayed Select the "Refresh" switch on the station list screen -
Wait for 10 minutes with the ignition switch ACC, and select the "Refresh" switch on the station list screen again -
Navigation receiver assembly Click here
After the voice recognition function or hands-free function is turned off, the cache radio does not operate Check that the cache radio setting is on -
Navigation receiver assembly Click here
When the cache radio is playing, sound is interrupted, sound cannot be heard or sound quality is poor Check if similar symptoms occur when receiving conventional FM/AM radio broadcasts -
Check if similar symptoms occur when receiving other broadcasts -
Move the vehicle to a place where the reception sensitivity is good and check again -
Navigation receiver assembly Click here
When the cache radio is playing, sound can be heard, but no information is displayed (some radio stations do not provide their name information) Check if similar symptoms occur when receiving other broadcasts -
Move the vehicle to a place where the reception sensitivity is good and check again -
Navigation receiver assembly Click here

HD Radio Function (w/ HD Radio Function)
Symptom Suspected Area Link
Only "HD Radio" stations cannot be heard or selected, or their analog or digital sound cannot be changed Check the "HD Radio" settings -
Navigation receiver assembly Click here
"iPod" tagging function cannot be used Check if a message indicating that the capacity for tag information is full is displayed -
Check that the cache radio is not playing (when the cache radio is playing, "iPod" tagging function cannot be used) -
Proceed to "USB Audio System Recognition/ Play Error" Click here
No. 1 stereo jack adapter assembly Click here
Navigation receiver assembly Click here
When the HD radio is playing, cover art may not be displayed When a song unregistered to the Gracenote CDDB is playing or cover art information is not provided by the broadcast station, its cover art cannot be displayed -
When the HD radio is playing, cover art cannot be displayed Navigation receiver assembly Click here
Broadcast station logo cannot be displayed Check if similar symptoms occur when receiving other broadcasts -
Check if similar symptoms occur with another vehicle -
Navigation receiver assembly Click here
SPS channel cannot be selected Check that HD radio FM mode is selected -
After pressing the "Refresh" switch, check that the SPS channel is on the station list -
Navigation receiver assembly Click here
When the SPS channel is selected, sound cannot be heard After pressing the "Refresh" switch, select the SPS channel on the station list -
Navigation receiver assembly Click here

SDARS System Function (w/ SDARS System)
Symptom Suspected Area Link
Satellite radio broadcast cannot be received or reception is bad Proceed to "Satellite Radio Broadcast cannot be Received" Click here
Stereo component tuner assembly Click here
Navigation receiver assembly Click here
Satellite radio cannot receive pay-type broadcasts Proceed to "Satellite Radio Broadcast cannot be Received" Click here
Stereo component tuner assembly Click here
Navigation receiver assembly Click here
Satellite radio broadcast cannot be selected or after selecting broadcast, broadcast cannot be added into memory Proceed to "Satellite Radio Broadcast cannot be Received" Click here
Proceed to "Satellite Radio Broadcast cannot be Selected or After Selecting Broadcast, Broadcast cannot be Added into Memory" Click here
Stereo component tuner assembly Click here
Navigation receiver assembly Click here
Satellite radio can be displayed but radio broadcast cannot be heard from speakers Check the volume settings -
Proceed to "Satellite Radio Broadcast cannot be Received" Click here
Stereo component tuner assembly Click here
Navigation receiver assembly Click here
Broadcast station logo cannot be displayed Proceed to "Satellite Radio Broadcast cannot be Received" Click here
Proceed to "Data Signal Circuit between Navigation Receiver Assembly and Extension Module" Click here
Stereo component tuner assembly Click here
Navigation receiver assembly Click here
Satellite radio text information cannot be displayed Proceed to "Satellite Radio Broadcast cannot be Received" Click here
Stereo component tuner assembly Click here
Navigation receiver assembly Click here
Satellite radio broadcast station cannot be selected (scan cannot be performed) Proceed to "Satellite Radio Broadcast cannot be Received" Click here
Stereo component tuner assembly Click here
Navigation receiver assembly Click here
When the satellite radio is playing, some cover art may not be displayed When a song unregistered to the Gracenote CDDB is playing, its cover art cannot be displayed -
When the satellite radio is playing, cover art cannot be displayed Navigation receiver assembly Click here

CD Player Function
Symptom Suspected Area Link
Disc cannot be played or player does not function with disc Proceed to "Disc Player Outline" in System Description and check if the disc is compatible with the disc player Click here
Proceed to "Check Optical Disc Error History" in Operation Check Click here
Navigation receiver assembly Click here
Disc cannot be inserted/played or disc is ejected right after insertion Proceed to "Check Optical Disc Error History" in Operation Check Click here
Proceed to "Disc cannot be Inserted or is Ejected Right After Insertion" Click here
Disc cannot be ejected Proceed to "Check Optical Disc Error History" in Operation Check Click here
Proceed to "Disc cannot be Ejected" Click here
Disc sound skips Proceed to "Check Optical Disc Error History" in Operation Check Click here
Proceed to "CD Sound Skips" Click here
Sound quality is bad only when disc is played (volume is too low) Proceed to "Check Optical Disc Error History" in Operation Check Click here
Proceed to "Sound Quality is Bad Only when Disc is Played (Volume is Too Low)" Click here
When disc is playing, some cover art is not displayed When a song unregistered to the Gracenote CDDB is playing, its cover art cannot be displayed -
When disc is playing, cover art cannot be displayed Navigation receiver assembly Click here
Album cover art cannot be displayed Check that Display Cover Art on the disc settings screen is set to on -
Check if similar symptoms occur with another vehicle -
Update the Gracenote database to the latest version -
Navigation receiver assembly Click here

AUX (Stereo Jack) Function
Symptom Suspected Area Link
External device sound cannot be heard or sound quality is bad (Stereo jack is used) Proceed to "Sound Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter" Click here
No. 1 stereo jack adapter assembly Click here
Navigation receiver assembly Click here
"AUX/USB" is not displayed on system check mode screen Proceed to "Sound Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter" Click here
No. 1 stereo jack adapter assembly Click here
Navigation receiver assembly Click here

Voice Recognition Function
Symptom Suspected Area Link
Voice menu screen is not displayed (Voice recognition function does not turn on) Check if the voice recognition prompts function is "On" -
Proceed to "Panel Switches do not Function" Click here
Proceed to "Steering Pad Switch Circuit" Click here
Navigation receiver assembly Click here
When voice recognition switch is pressed, a short beep is emitted but voice cannot be recognized properly Proceed to "Voice is not Recognized" Click here
Proceed to "Microphone Circuit between Microphone and Navigation Receiver Assembly" Click here
SD card -
Navigation receiver assembly Click here

"Bluetooth" Hands-free Function
Symptom Suspected Area Link
"Bluetooth" is inoperative (In-vehicle device cannot be recognized by the cellular phone) Proceed to "Cellular Phone Inspection" Click here
Navigation receiver assembly Click here
"Bluetooth" compatible cellular phone cannot be registered Proceed to "Cellular Phone Registration Failure" Click here
"Bluetooth" compatible cellular phone cannot be connected Check that no other cellular phone is connected as a hands-free device -
Bring the cellular phone near the in-vehicle device and reconnect it -
Proceed to "Cellular Phone Inspection" Click here
Navigation receiver assembly Click here
"Bluetooth" compatible cellular phone cannot be connected automatically (can be connected manually) Check that "Bluetooth" automatic connection setting of the in-vehicle device is on -
Navigation receiver assembly Click here
"Bluetooth" compatible cellular phone connection is disconnected Bring the cellular phone near the in-vehicle device and check if it is reconnected -
Proceed to "Cellular Phone Inspection" Click here
Navigation receiver assembly Click here
Message that prompts to check the cellular phone is displayed Bring the cellular phone near the in-vehicle device and check if it is reconnected -
Proceed to "Cellular Phone Inspection" Click here
Navigation receiver assembly Click here
When the ignition switch is turned to ACC, instructions for checking the connection condition between the in-vehicle device and cellular phone are displayed Turn the cellular phone connection conformation display on the in-vehicle device off -
Phonebook data cannot be transferred Check that the phonebook automatic transfer setting of the in-vehicle device is on -
Enter "1234" into the "Bluetooth" phone (when transferring phonebook data, OBEX authentication may be required) -
Check that no applications on the cellular phone are running -
If using "Bluetooth" audio function, cancel the "Bluetooth" audio player connection and check the operation -
Transfer phonebook data manually -
Proceed to "Cellular Phone Inspection" Click here
Navigation receiver assembly Click here
Phonebook data is cleared Navigation receiver assembly Click here
Phonebook data cannot be edited Check that the phonebook data automatic transfer setting is off -
Navigation receiver assembly Click here
All the transferred phonebook data is sorted to "Other" Check that the phonebook data automatic transfer setting is off -
Check that phonebook data in the cellular phone is not stored to the SIM card -
Proceed to "Cellular Phone Inspection" Click here
Explain to the customer that all the transferred phonebook data may be stored to "Other" depending on cellular phone -
Cellular phone cannot make outgoing/ incoming calls Move the vehicle into a cellular phone service area, check that the "Bluetooth" device is connected to the vehicle and operate device again -
Check that the cellular phone can make outgoing/incoming calls properly when not connected via "Bluetooth" -
Proceed to "Cellular Phone Inspection" Click here
Navigation receiver assembly Click here
Other caller's voice is interrupted by noise or sound quality is poor Check the receiving voice volume (if it is too high, voice may sound distorted) -
Make a call with the cellular phone disconnected from "Bluetooth" and check that other caller's voice can be heard clearly -
Proceed to "Check Hands-free Voice Quality Setting" in Operation Check Click here
Proceed to "Cellular Phone Inspection" Click here
Navigation receiver assembly Click here
Other caller's voice cannot be heard Check that reception voice volume is not set to minimum -
Make a call with the cellular phone disconnected from "Bluetooth" and check that other caller's voice can be heard clearly -
Proceed to "Check Hands-free Voice Quality Setting" in Operation Check Click here
Proceed to "Cellular Phone Inspection" Click here
Navigation receiver assembly Click here
Caller's voice (your voice) is interrupted by noise or sound quality is poor Check the transmitting voice volume (if it is too high, voice may sound distorted) -
Check that nothing can cause noise around the microphone (an outlet of the air conditioning system facing the microphone, wind from an open window, additional devices, etc. may affect noise occurrence) -
Proceed to "Check Hands-free Voice Quality Setting" in Operation Check Click here
Proceed to "Cellular Phone Inspection" Click here
Proceed to "Microphone Circuit between Microphone and Navigation Receiver Assembly" Click here
Other caller cannot hear your voice When talking on the cellular phone, check that the mute button is not pressed -
Check that nothing can cause noise around the microphone (an outlet of the air conditioning system facing the microphone, wind from an open window, additional devices, etc. may affect noise occurrence) -
Proceed to "Check Hands-free Voice Quality Setting" in Operation Check Click here
Proceed to "Cellular Phone Inspection" Click here
Proceed to "Microphone Circuit between Microphone and Navigation Receiver Assembly" Click here
No notification when a new SMS/MMS/e-mail has been received Check the SMS/MMS/e-mail notification settings on the cellular phone and the Navigation receiver assembly -
Proceed to "Cellular Phone Inspection" Click here
Navigation receiver assembly Click here
Received SMS/MMS/e-mail cannot be read Check the SMS/MMS/e-mail transfer settings on the cellular phone and the Navigation receiver assembly -
Proceed to "Cellular Phone Inspection" Click here
Navigation receiver assembly Click here
SMS/MMS/e-mail cannot be replied to Move the vehicle into a cellular phone service area, and check the operation of the Navigation receiver assembly and cellular phone -
Check that the cellular phone can send an SMS/MMS/e-mail -
Proceed to "Cellular Phone Inspection" Click here
Navigation receiver assembly Click here

"Bluetooth" Audio Function
Symptom Suspected Area Link
Portable player cannot be registered Proceed to "Portable Player cannot be Registered" Click here
Navigation receiver assembly Click here
Portable player cannot be connected manually/automatically Proceed to "Portable Player cannot be Registered" Click here
Proceed to "Portable Player cannot be Connected Manually/Automatically" Click here
Navigation receiver assembly Click here
Cellular phone with portable audio function cannot be recognized as "Bluetooth" audio device even when connected using "Bluetooth" Proceed to "Portable Player cannot be Registered" Click here
Proceed to "Portable Player cannot be Connected Manually/Automatically" Click here
Navigation receiver assembly Click here
Sound of portable player cannot be heard from speakers, or sound is low Proceed to "Sound of Portable Player cannot be Heard from Speakers or Sound is Low" Click here
Navigation receiver assembly Click here
Portable player does not play even after "Bluetooth" audio mode is selected Proceed to "Does not Play even after Bluetooth Audio Mode is Selected" Click here
Navigation receiver assembly Click here
Portable player does not play Proceed to "Does not Play even after Bluetooth Audio Mode is Selected" Click here
Navigation receiver assembly Click here
Track information such as track number, track name, elapsed play time and playlist is not displayed Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device" Click here
Navigation receiver assembly Click here
Operation switches for portable player such as play, pause, repeat, random and scan are not displayed Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device" Click here
Navigation receiver assembly Click here
Battery condition of portable player is not displayed Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device" Click here
Navigation receiver assembly Click here
Battery condition of portable player is not displayed Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device" Click here
Navigation receiver assembly Click here
Portable player cannot pause, select file, fast forward, fast rewind, play at random or scan Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device" Click here
Navigation receiver assembly Click here
Noise occurs or sound skips when portable player plays Proceed to "Noise Occurs or Sound Skips when Portable Player Plays" Click here
Navigation receiver assembly Click here
Registered device cannot be deleted Proceed to "Registered Device cannot be Deleted" Click here
Navigation receiver assembly Click here

USB Audio System Function
Symptom Suspected Area Link
USB audio system sound cannot be heard or sound quality is bad (USB connector is used) Proceed to "Data Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter" Click here
No. 1 stereo jack adapter assembly Click here
Navigation receiver assembly Click here
USB device or "iPod" is not recognized Proceed to "USB Audio System Recognition/Play Error" Click here
No. 1 stereo jack adapter assembly Click here
Navigation receiver assembly Click here
Track information such as track, artist and album names are not displayed Proceed to "USB Audio System Recognition/Play Error" Click here
No. 1 stereo jack adapter assembly Click here
Navigation receiver assembly Click here
USB device or "iPod" is recognized but cannot play, or can play but not in a sorted order Proceed to "USB Audio System Recognition/Play Error" Click here
No. 1 stereo jack adapter assembly Click here
Navigation receiver assembly Click here
Album cover art cannot be displayed Check that Display Cover Art on the "iPod" or USB Settings screen is set to on -
Check if similar symptoms occur with another vehicle -
Update the Gracenote database to the latest version -
Navigation receiver assembly Click here
User set album cover art cannot be displayed Check if the priority display of Gracenote database album cover art setting is off -
Check that a JPEG file is used for the album cover art registered to the music data in the USB device or "iPod" - Navigation receiver assembly -
Navigation receiver assembly Click here
"iPod" battery cannot be charged Proceed to "USB Audio System Recognition/Play Error" Click here
No. 1 stereo jack adapter assembly Click here
Navigation receiver assembly Click here

Customize Startup Image or Screen Off Image Function
Symptom Suspected Area Link
Screen cannot be changed to UIC setting screen Navigation receiver assembly Click here
Thumbnails for opening image setting or screen off image setting do not update when USB device is connected Check that the USB device was not disconnected while transferring an image -
Check that the screen was not changed to another function menu while transferring an image -
Proceed to "USB Audio System Recognition/ Play Error" Click here
No. 1 stereo jack adapter assembly Click here
Navigation receiver assembly Click here
Transfer button cannot be pressed Check that a USB device is connected -
Check that the USB device is not in use (USB audio system is playing etc.) -
Proceed to "USB Audio System Recognition/ Play Error" Click here
No. 1 stereo jack adapter assembly Click here
Navigation receiver assembly Click here
Image data in USB device cannot be displayed Check that the designated folder name is used -
Check that the file extension of the data is JPG or JPEG -
Check that the file name is 32 characters or less and available language is used -
Check that the image data size is 10 MB or less -
Check that the file system of the USB device is FAT16 or FAT32 -
Proceed to "USB Audio System Recognition/ Play Error" Click here
No. 1 stereo jack adapter assembly Click here
Navigation receiver assembly Click here
Set opening image or screen off image is not displayed Check if it is the first start-up after disconnecting and reconnecting the +B terminal (reading from the SD card may be slow when the system is first starting-up) -
Set the opening image or screen off image again -
Navigation receiver assembly Click here
Stored image cannot be deleted Navigation receiver assembly Click here
Message indicating that USB device cannot be accessed is displayed Check that the USB device has not been disconnected while the navigation system is recognizing it -
Proceed to "USB Audio System Recognition/ Play Error" Click here
No. 1 stereo jack adapter assembly Click here
Navigation receiver assembly Click here
Thumbnail images for opening image or screen off image are not displayed on setting screen Check if it is the first start-up after disconnecting and reconnecting the +B terminal (reading from the SD card may be slow when the system is first starting-up) -
Set the opening image or screen off image again -
Navigation receiver assembly Click here
Image cannot be set for opening image or screen off image on setting screen Set the opening image or screen off image again -
Navigation receiver assembly Click here

Fuel Consumption Function
Symptom Suspected Area Link
"Fuel Consumption" icon is dimmed Check if other icons or items displayed on screen have any problems -
Navigation receiver assembly Click here
Graph is not displayed on "Trip Information" screen Recheck with the engine running -
Navigation receiver assembly Click here
Cruise range is not displayed on "Trip Information" screen Turn the ignition switch to ON and recheck -
Navigation receiver assembly Click here
Graph is not updated on "Past record" screen even though "Clear" is selected Turn the ignition switch to ON and recheck -
Navigation receiver assembly Click here
Graph is not displayed on "Past record" screen Turn the ignition switch to ON and recheck -
Navigation receiver assembly Click here

Entune App Suite Function (w/ Entune App Suite Function)
Symptom Suspected Area Link
An Entune App Suite system error message is displayed on the screen Follow on screen instructions -
Proceed to "Confirm Cellular Phone Functionality" Click here
Proceed to "Confirm Vehicle Headunit Functionality" Click here
Proceed to "Entune App Suite Reset Procedure" in Operation Check Click here
Navigation receiver assembly Click here
Entune App Suite apps and services are not operating as expected Proceed to "Confirm Cellular Phone Functionality" Click here
Proceed to "Confirm Vehicle Headunit Functionality" Click here
Proceed to "Entune App Suite Reset Procedure" in Operation Check Click here
Navigation receiver assembly Click here
Entune App Suite voice recognition is not possible (voice recognition on the navigation system is normal) Proceed to "Confirm Cellular Phone Functionality" Click here
Proceed to "Confirm Vehicle Headunit Functionality" Click here
Proceed to "Entune App Suite Reset Procedure" in Operation Check Click here
Navigation receiver assembly Click here
Poor sound quality of Entune App Suite system Confirm that cellular phone handset volume is turned up -
Confirm that adequate signal is maintained during driving -
Proceed to "Confirm Cellular Phone Functionality Click here
Proceed to "Confirm Vehicle Headunit Functionality" Click here
Proceed to "Entune App Suite Reset Procedure" in Operation Check Click here
Navigation receiver assembly Click here
Entune App Suite function does not operate properly (no sound is output although the Entune App Suite screen is displayed properly) If the "iPhone" is connected to the USB port of the No. 1 stereo jack adapter, Entune App Suite audio may not be output. Therefore, disconnect the "iPhone" from the USB port of the No. 1 stereo jack adapter, change the audio output source of the "iPhone" or turn the ignition switch off and then to ON again. -