Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2013.11
RM30B0U _56 Audio / Visual / Telematics _009009 NAVIGATION / MULTI INFO DISPLAY _0104226 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Stereo Component Amplifier Power Source Circuit  


WIRING DIAGRAM

This circuit provides power to the stereo component amplifier assembly.

WIRING DIAGRAM

E289278
0.354,0.521 2.188,0.719 1.833,0.198 10 false from Battery 0.135,1.313 1.969,1.51 1.833,0.198 10 false from ACC Relay 2.708,0.719 3.146,0.885 0.438,0.167 10 false AMP 2.719,1.531 3.156,1.698 0.438,0.167 10 false ACC 5,0.542 5.438,0.708 0.438,0.167 10 false M23 5.01,1.333 5.448,1.5 0.438,0.167 10 false M22 5.01,2.208 5.448,2.375 0.438,0.167 10 false M23 5.104,1.979 5.542,2.146 0.438,0.167 10 false 3 5.052,1.135 5.49,1.302 0.438,0.167 10 false 12 5.073,0.333 5.51,0.5 0.438,0.167 10 false 1 5.354,0.552 5.906,0.719 0.552,0.167 10 false +B 5.385,1.333 5.938,1.5 0.552,0.167 10 false ACC 5.375,2.229 5.927,2.396 0.552,0.167 10 false GND 4.979,2.823 6.75,3.198 1.771,0.375 10 false Stereo Component Amplifier Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E271825
1.49,0.083 1.906,0.292 0.417,0.208 1.49,1.719 1.906,1.927 0.417,0.208 0.917,2.375 1.094,1.844 true 0.417,1.885 0.573,2.385 true 2.656,0.958 2.896,1.271 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 1.563,0.104 1.875,0.281 0.313,0.177 10 false M22 1.563,1.74 1.875,1.958 0.313,0.219 10 false M23 1.146,1.771 1.49,1.979 0.344,0.208 10 false GND 0.177,1.792 0.417,2.01 0.24,0.219 10 false +B 2.958,1.188 3.313,1.396 0.354,0.208 10 false ACC
*a Front view of wire harness connector
(to Stereo Component Amplifier Assembly)


Disconnect the stereo component amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M23-3 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M23-1 (+B) - Body ground Always 11 to 14 V
M22-12 (ACC) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR