Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0046807 ECD SYSTEM(for DPF) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

A208462
1.469,2 1.625,1.76 1.625,1.76 1.771,1.76 false 0.208,0.146 0.906,0.49 0.698,0.344 10 false (Fig. 1) 0.208,0.542 1.313,0.823 1.104,0.281 10 false Resistance kΩ 1.823,1.688 2.656,2.031 0.833,0.344 10 false Acceptable 1.208,4.073 2.521,4.385 1.313,0.313 10 false Temperature °C (°F)

The intake air temperature sensor is built into the mass air flow meter assembly and senses the intake air temperature.

A thermistor built into the sensor changes its resistance value according to the intake air temperature.

The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).

The intake air temperature sensor is connected to the ECM.

The 5 V power source voltage in the ECM is applied to the intake air temperature sensor from terminal THA via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes in accordance with the intake air temperature, the voltage at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability with a cold engine.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0112 Intake Air Temperature Circuit Low Input Short in the intake air temperature sensor for 0.5 seconds.
(1 trip detection logic)
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter assembly)

·

ECM


Comes on DTC stored
P0113 Intake Air Temperature Circuit High Input Open in the intake air temperature sensor for 0.5 seconds.
(1 trip detection logic)
·

Open in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter assembly)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0112 Intake Air
P0113

HINT:
·

If DTC P0112 and/or P0113 is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power


·

When DTC P0112 or P0113 is stored, check the intake air temperature by entering the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Reference
Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0112 Ignition switch ON for 0.5 seconds
P0113

WIRING DIAGRAM

A256089
0.156,2.698 2.417,3.135 2.26,0.438 10 false Intake Air Temperature Sensor (Built into Mass Air Flow Meter Assembly) 5.938,3.042 7.146,3.354 1.208,0.313 10 false ECM 4.938,1.313 5.198,1.563 0.26,0.25 10 false 110 5.885,0.896 6.292,1.104 0.406,0.208 10 false 5 V 5.021,1.917 5.281,2.073 0.26,0.156 10 false 87 5.271,1.313 5.604,1.479 0.333,0.167 10 false THA 5.271,1.917 5.667,2.073 0.396,0.156 10 false ETHA 1.823,1.313 2.135,1.469 0.313,0.156 10 false THA 1.927,1.917 2.146,2.073 0.219,0.156 10 false E2 2.208,1.313 2.323,1.469 0.115,0.156 10 false 4 2.208,1.917 2.313,2.073 0.104,0.156 10 false 5 5.885,1.188 5.99,1.344 0.104,0.156 10 false R 0.156,2.531 0.448,2.688 0.292,0.156 10 false B1 5.406,3.042 6.01,3.333 0.604,0.292 10 false B76

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).


HINT:
·

If DTCs relating to different systems are stored and they share terminal E2 as their ground, check this ground circuit first.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 61 318

d.

Read the value.

OK:

Same as actual intake air temperature


Result:
Proceed to
-40°C (-40°F)
140°C (284°F) or higher
OK (same as actual intake air temperature)


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or higher.





-40°C (-40°F)

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

140°C (284°F) or higher

7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

OK (same as actual intake air temperature)

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A128460
0.25,3.271 0.719,3.531 0.469,0.26 1.854,3.448 1.573,4.021 false 2.104,3.458 2.344,3.969 false 2.333,4 2.563,4.198 0.229,0.198 10 E2 2.458,1.031 2.792,1.229 0.333,0.198 10 THA 1.24,4 1.573,4.198 0.333,0.198 10 THA 2.469,1.5 2.854,1.656 0.385,0.156 10 ETHA 0.792,0.146 1.083,0.406 0.292,0.26 10 *1 2.646,0.146 2.917,0.375 0.271,0.229 10 *2 0.135,2.188 0.438,2.438 0.302,0.25 10 *a 0.375,3.313 0.563,3.479 0.188,0.167 10 B1
*1 Mass Air Flow Meter Assembly
*2 ECM
*a Front view of wire harness connector
(to Mass Air Flow Meter Assembly)


Disconnect the mass air flow meter assembly connector.


b.

Connect terminals 4 (THA) and 5 (E2) of the mass air flow meter assembly wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 61 318

f.

Read the value.

OK:

140°C (284°F) or higher



Result:
Proceed to
OK
NG



OK

3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER ASSEMBLY.

NG

4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER ASSEMBLY - ECM)
3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER ASSEMBLY.
a.

Replace the mass air flow meter assembly.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B1-4 (THA) - B76-110 (THA) Always Below 1 Ω
B1-5 (E2) - B76-87 (ETHA) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A226261C06
0.823,1.74 1.5,2.063 0.677,0.323 10 *1 2.646,1.74 3.167,1.896 0.521,0.156 10 *2 2.021,0.656 2.542,0.938 0.521,0.281 10 THA 1.938,1 2.688,1.208 0.75,0.208 10 ETHA
*a Mass Air Flow Meter Assembly
*b ECM


Disconnect the mass air flow meter assembly connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 61 318

e.

Read the value.

OK:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

8.REPLACE MASS AIR FLOW METER ASSEMBLY

NG

9.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER ASSEMBLY - ECM)
8.REPLACE MASS AIR FLOW METER ASSEMBLY
a.

Replace the mass air flow meter assembly.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B1-4 (THA) or B76-110 (THA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch to ON for 1 second.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END