A thermistor is built into the engine coolant temperature sensor and it changes its resistance value according to the engine coolant temperature.
The structure of the sensor and connection to the ECM is the same as the intake air temperature sensor.
If DTC P0115, P0117 or P0118 is stored, the ECM operates the fail-safe function in which the ECT is assumed to be 80°C (176°F).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0115 | Engine Coolant Temperature Circuit | Open or short in the engine coolant temperature sensor circuit for 0.5 seconds.
(1 trip detection logic) |
·
Open or short in engine coolant temperature sensor circuit ·
Engine coolant temperature sensor ·
ECM |
Comes on | DTC stored |
| P0117 | Engine Coolant Temperature Circuit Low Input | Short in the engine coolant temperature sensor circuit for 0.5 seconds.
(1 trip detection logic) |
·
Short in engine coolant temperature sensor circuit ·
Engine coolant temperature sensor ·
ECM |
Comes on | DTC stored |
| P0118 | Engine Coolant Temperature Circuit High Input | Open in the engine coolant temperature sensor circuit for 0.5 seconds.
(1 trip detection logic) |
·
Open in engine coolant temperature sensor circuit ·
Engine coolant temperature sensor ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0115 | Coolant Temp |
| P0117 | |
| P0118 |
If DTC P0115, P0117 and/or P0118 is stored, the following symptoms may appear:
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
When DTC P0115, P0117 and/or P0118 is stored, check the engine coolant temperature by entering the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
| Temperature Displayed | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) or higher | Short circuit |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0115 | Ignition switch ON for 0.5 seconds |
| P0117 | |
| P0118 |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
| Tester Display |
|---|
| Coolant Temp |
Read the value.
75 to 90°C (167 to 194°F) with warm engine.
| Proceed to |
|---|
| -40°C (-40°F) |
| 140°C (284°F) or higher |
| 75 to 90°C (167 to 194°F) |
If there is an open circuit, the GTS indicates -40°C (-40°F).
If there is a short circuit, the GTS indicates 140°C (284°F) or higher.
-40°C (-40°F)
140°C (284°F) or higher
75 to 90°C (167 to 194°F)
| *1 | Engine coolant temperature sensor |
| *2 | ECM |
| *a | Front view of wire harness connector
(to Engine coolant temperature sensor) |
Disconnect the engine coolant temperature sensor connector.
Connect terminals 1 and 2 of the engine coolant temperature sensor connector on the wire harness side.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
| Tester Display |
|---|
| Coolant Temp |
Read the value.
140°C (284°F) or higher
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the engine coolant temperature sensor.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the engine coolant temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B4-2 - B76-111 (THW) | Always | Below 1 Ω |
| B4-1 - B76-88 (ETHW) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | Engine Coolant Temperature Sensor |
| *2 | ECM |
Disconnect the engine coolant temperature sensor connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
| Tester Display |
|---|
| Coolant Temp |
Read the value.
-40°C (-40°F)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the engine coolant temperature sensor.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the engine coolant temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B4-2 or B76-111 (THW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch to ON for 1 second.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT