Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0046807 ECD SYSTEM(for DPF) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.5 mph) or more for more than 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High Conditions (a), (b) and (c) are met for 20 seconds
(a) Vehicle speed is more than 20 km/h (12.5 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is on.
(1 trip detection logic)
·

ST relay circuit

·

Clutch pedal switch


Comes on DTC stored

Related Data List
DTC No. Data List
P0617 Starter Signal

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0617 Drive vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or higher

WIRING DIAGRAM

A284190
0.104,0.083 4.875,0.323 4.771,0.24 12 false w/ Entry and Start System: 0.198,2.646 2.396,3.104 2.198,0.458 10 false Certification ECU (Smart Key ECU Assembly) 0.198,2.458 0.615,2.656 0.417,0.198 10 false G82 5.344,1.052 5.76,1.25 0.417,0.198 10 false A61 5.354,3.771 5.771,3.969 0.417,0.198 10 false A61 4.177,2.25 4.594,2.448 0.417,0.198 10 false A4*1 4.188,2.458 4.604,2.656 0.417,0.198 10 false F2*2 3.917,5.792 4.604,5.958 0.688,0.167 10 false *1: LHD 3.927,6.021 4.615,6.188 0.688,0.167 10 false *2: RHD 4.198,2.698 5.385,3.094 1.188,0.396 10 false Clutch Start Switch Assembly 1.635,6.708 2.135,7.031 0.5,0.323 10 false Starter 0.729,6.792 1.229,7.115 0.5,0.323 10 false Battery 3.271,4.573 3.958,4.74 0.688,0.167 10 false ST 0.583,3.792 1.271,3.958 0.688,0.167 10 false ST 1.365,2.125 1.823,2.323 0.458,0.198 10 false STA 1.365,1.021 1.625,1.24 0.26,0.219 10 false NE 1.281,1.594 1.802,1.813 0.521,0.219 10 false STAR 5.688,1.052 6.24,1.271 0.552,0.219 10 false NEO 5.688,3.656 6.146,3.854 0.458,0.198 10 false STA 5.396,3.552 5.75,3.75 0.354,0.198 10 false 43 1.771,0.917 2.125,1.115 0.354,0.198 10 false 16 5.354,0.844 5.708,1.042 0.354,0.198 10 false 10 1.802,1.479 2.156,1.677 0.354,0.198 10 false 5 1.802,1.99 2.156,2.188 0.354,0.198 10 false 7 2.479,4.104 2.833,4.302 0.354,0.198 10 false 5 2.49,5.052 2.844,5.25 0.354,0.198 10 false 3 3.052,4.115 3.406,4.313 0.354,0.198 10 false 2 3.063,5.052 3.417,5.25 0.354,0.198 10 false 1 6.115,5.031 6.573,5.229 0.458,0.198 10 false ECM 1.76,5.688 2.115,5.896 0.354,0.208 10 false B6 1.063,5.917 1.417,6.125 0.354,0.208 10 false C4 1.563,5.667 1.917,5.865 0.354,0.198 10 false 1 1.083,5.74 1.438,5.938 0.354,0.198 10 false 1 0.563,4.844 1.406,5.052 0.844,0.208 10 false FL MAIN 3.698,2.073 4.052,2.271 0.354,0.198 10 false 2 3.708,2.979 4.063,3.177 0.354,0.198 10 false 1

A284191
4.229,2.323 5.531,2.771 1.302,0.448 10 false Clutch Start Switch Assembly 0.104,0.052 2.302,0.458 2.198,0.406 12 false w/o Entry and Start System: 1.406,1.823 2.604,2.042 1.198,0.219 10 false Ignition Switch 1.583,6.479 2.115,6.844 0.531,0.365 10 false Starter 0.729,6.542 1.26,6.906 0.531,0.365 10 false Battery 3.302,4.344 3.615,4.542 0.313,0.198 10 false ST 1.5,3.229 1.813,3.427 0.313,0.198 10 false ST 0.594,2.198 1.031,2.375 0.438,0.177 10 false AM2 1.25,1.646 1.688,1.823 0.438,0.177 10 false G4 1.521,1.156 1.958,1.333 0.438,0.177 10 false AM2 2.146,1.135 2.583,1.313 0.438,0.177 10 false ST2 1.25,1.135 1.531,1.302 0.281,0.167 10 false 4 2.5,1.135 2.781,1.302 0.281,0.167 10 false 2 1.042,5.698 1.479,5.875 0.438,0.177 10 false C4 1.792,5.469 2.229,5.646 0.438,0.177 10 false B6 1.563,5.458 1.875,5.656 0.313,0.198 10 false 1 1.115,5.531 1.427,5.729 0.313,0.198 10 false 1 2.469,3.885 2.667,4.083 0.198,0.198 10 false 5 2.479,4.823 2.677,5.021 0.198,0.198 10 false 3 3.042,3.875 3.24,4.073 0.198,0.198 10 false 2 3.042,4.844 3.24,5.042 0.198,0.198 10 false 1 5.354,3.552 5.667,3.75 0.313,0.198 10 false A61 5.375,3.354 5.688,3.552 0.313,0.198 10 false 43 5.698,3.438 6.01,3.635 0.313,0.198 10 false STA 6.094,4.802 6.781,5.063 0.688,0.26 10 false ECM 4.198,1.792 4.625,2.01 0.427,0.219 10 false A4*1 4.208,2 4.635,2.219 0.427,0.219 10 false F2*2 3.969,5.5 4.5,5.677 0.531,0.177 10 false *1: LHD 3.99,5.76 4.521,5.938 0.531,0.177 10 false *2: RHD 0.573,4.729 1.406,4.958 0.833,0.229 10 false FL MAIN 3.76,1.802 3.958,2 0.198,0.198 10 false 2 3.792,2.802 3.99,3 0.198,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).


HINT:
·

The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to the Problem Symptoms Table (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>PROBLEM SYMPTOMS TABLE).

·

If this DTC is output, inspect the starter.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 61 193

d.

Read the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more.

NOTICE:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


Result:
Condition Starter Signal Proceed to
Driving at 20 km/h (12.4 mph) or more OFF A
ON (w/ entry and start system) B
ON (w/o entry and start system) C




A

B

2.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

C

6.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
2.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (ECM - clutch start switch assembly - certification ECU (smart key ECU assembly) - ST relay).


Result:
Proceed to
NEXT



NEXT

3.CONFIRM WHETHER DTC OUTPUT RECURS
3.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

h.

Read the DTCs.

Result:
Proceed to
DTC P0617 is output
DTC is not output




DTC P0617 is output

4.REPLACE ECM

DTC is not output

END

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER DTC OUTPUT RECURS
5.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

6.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>2AD-FTV STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

8.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
7.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (ECM - clutch start switch assembly - ignition or starter switch assembly - ST relay).


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER DTC OUTPUT RECURS
8.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
a.

Replace the ignition or starter switch assembly.

Click hereEngine / Hybrid System>2AD-FTV STARTING>IGNITION SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER DTC OUTPUT RECURS