Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0046807 ECD SYSTEM(for DPF) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P2237  Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)  P2238  Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)  P2239  Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)  P2252  Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)  P2253  Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)  


DESCRIPTION

HINT:
·

For more information on the air fuel ratio sensor and Diesel Particulate Filter (DPF), refer to the following procedures (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).

·

If P2237, P2238 and/or P2239 is present, refer to the DTC table for DPF system (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).

·

These DTCs are recorded when the A/F sensor has a malfunction, although the title is the oxygen sensor.



The air fuel ratio sensor has the characteristic of providing output voltage which is proportional to the air fuel ratio. The air fuel ratio sensor output voltage*1 is used by the ECM to control the air fuel ratio.

The air fuel ratio sensor is located after the DPF catalytic converter. This sensor has been developed based on the structure and technology of a sensor that is being used for gasoline engines. The cover portion of the sensor has been changed for use in the diesel engine with DPF in order to eliminate the influence of the sensor temperature and particulate matter (PM).

In order to reduce both PM, the ECM adjusts the air-fuel ratio to slightly rich (but it is lean compared with the stoichiometric air-fuel ratio) based on signals from the air fuel ratio sensor. When the ECM performs PM forced regeneration by adding fuel using the exhaust fuel addition injector, the air-fuel ratio is also properly adjusted using the sensor.

*1: The voltage value changes inside the ECM only.

A264921
5.24,2 5.771,2.521 false 5.052,1.823 5.719,2.01 false 5.177,1.417 5.688,1.365 false 5.406,1.302 5.729,1.125 false 5.208,1.76 5.719,2.01 false 3.115,2.063 3.75,1.719 false 2.958,2.104 2.24,1.74 false 2.583,2.625 2.708,2.823 0.125,0.198 10 false A 3.271,2.625 3.396,2.802 0.125,0.177 10 false A 1.677,1.615 2.25,1.813 0.573,0.198 10 false Element 0.677,2.063 1.552,2.281 0.875,0.219 10 false Exhaust Gas 4.875,2.667 5.635,2.865 0.76,0.198 10 false A-A Section 5.74,1.927 6.969,2.146 1.229,0.219 10 false Platinum Electrode 3.813,1.635 4.229,1.813 0.417,0.177 10 false Cover 5.802,2.448 6.094,2.646 0.292,0.198 10 false Air 5.76,0.958 6.219,1.135 0.458,0.177 10 false Heater 5.729,1.219 6.927,1.604 1.198,0.385 10 false Solid Electrolyte (Zirconia Element) 0.354,4.656 1.604,4.938 1.25,0.281 10 false AF Lambda B1S1 0.333,5.958 1.563,6.125 1.229,0.167 10 false AFS Voltage B1S1 1.99,4.729 2.156,4.938 0.167,0.208 10 false 1 1.99,4.198 2.156,4.406 0.167,0.208 10 false 2 2,6.094 2.167,6.302 0.167,0.208 10 false 1 2,6.635 2.167,6.844 0.167,0.208 10 false 0 1.99,5.25 2.156,5.458 0.167,0.208 10 false 0 2,5.573 2.167,5.781 0.167,0.208 10 false 2 2.26,5.552 2.49,5.802 0.229,0.25 10 false (V) 2.885,6.844 3.135,7.094 0.25,0.25 10 false 10 3.198,6.927 3.552,7.177 0.354,0.25 10 false 14.5 3.646,6.844 3.896,7.094 0.25,0.25 10 false 20 4.417,6.844 4.667,7.094 0.25,0.25 10 false 30 5.188,6.844 5.438,7.094 0.25,0.25 10 false 40 5.948,6.844 6.198,7.094 0.25,0.25 10 false 50 0.188,2.979 2.625,3.156 2.438,0.177 10 false Air Fuel Ratio Displayed on the GTS: 3.646,7.125 4.583,7.323 0.938,0.198 10 false Air Fuel Ratio 4.052,4.854 6.677,5.167 2.625,0.313 10 false AF Lambda B1S1 = Air Fuel Ratio / 14.5 2.219,7.802 2.635,7.99 0.417,0.188 10 false 0.060 4.635,7.802 5.052,7.99 0.417,0.188 10 false 0.508 5.229,7.802 5.646,7.99 0.417,0.188 10 false 0.787 5.833,7.802 6.25,7.99 0.417,0.188 10 false 0.978 6.385,7.802 6.802,7.99 0.417,0.188 10 false 1.373 4.031,7.802 4.448,7.99 0.417,0.188 10 false 0.356 3.427,7.802 3.844,7.99 0.417,0.188 10 false 0.268 2.833,7.802 3.25,7.99 0.417,0.188 10 false 0.170 1.729,7.802 1.917,7.99 0.188,0.188 10 false 0 1.656,8.833 1.99,9.021 0.333,0.188 10 false 14.5 5.896,8.833 6.229,9.021 0.333,0.188 10 false 30 2.302,8.833 2.635,9.021 0.333,0.188 10 false 15 4.698,8.833 5.031,9.021 0.333,0.188 10 false 20 6.5,8.833 6.833,9.021 0.333,0.188 10 false 50 3.5,8.833 3.833,9.021 0.333,0.188 10 false 17 2.906,8.833 3.24,9.021 0.333,0.188 10 false 16 0.531,8.833 1.469,9.031 0.938,0.198 10 false Air Fuel Ratio 4.104,8.833 4.438,9.021 0.333,0.188 10 false 18 5.302,8.833 5.635,9.021 0.333,0.188 10 false 25 1.292,7.781 1.521,7.979 0.229,0.198 10 false (V) 0.458,7.708 1.25,8.031 0.792,0.323 10 false AFS Voltage B1S1 0.49,8.24 1.292,8.573 0.802,0.333 10 false AF Lambda B1S1 1.698,8.333 1.927,8.5 0.229,0.167 10 false 1.0 2.25,8.333 2.594,8.51 0.344,0.177 10 false 1.03 2.854,8.333 3.167,8.531 0.313,0.198 10 false 1.10 3.427,8.333 3.74,8.479 0.313,0.146 10 false 1.17 4.073,8.333 4.365,8.531 0.292,0.198 10 false 1.24 4.635,8.333 4.948,8.479 0.313,0.146 10 false 1.38 5.25,8.333 5.583,8.49 0.333,0.156 10 false 1.72 5.844,8.333 6.135,8.479 0.292,0.146 10 false 2.07 6.448,8.333 6.771,8.49 0.323,0.156 10 false 3.45 0.375,9.24 0.771,9.427 0.396,0.188 10 false HINT: 0.646,9.469 6.198,9.625 5.552,0.156 10 false AFS Voltage B1S1 cannot be displayed correctly when the value is 0 V. 2,3.677 2.167,3.885 0.167,0.208 10 false 3

HINT:

The ECM provides a pulse width modulated control circuit to adjust current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.


A275096
3.521,0.833 3.615,1.01 3.615,1.01 3.802,1.01 false 3.521,1.281 3.615,1.458 3.615,1.458 3.802,1.458 false 0.104,0.063 0.885,0.25 0.781,0.188 10 false Reference: 0.063,0.854 0.99,1.333 0.927,0.479 10 false from EFI-MAIN NO. 2 Relay 1.135,0.906 1.781,1.094 0.646,0.188 10 false EFI NO.2 2.823,0.365 4.198,0.625 1.375,0.26 10 false Air Fuel Ratio Sensor 3.865,0.938 4.375,1.115 0.51,0.177 10 false Heater 3.854,1.365 4.365,1.563 0.51,0.198 10 false Sensor 4.823,0.625 5.292,0.823 0.469,0.198 10 false HAF2 4.833,1.052 5.24,1.24 0.406,0.188 10 false AF2+ 4.823,1.458 5.26,1.646 0.438,0.188 10 false AF2- 5.604,2.344 6.063,2.542 0.458,0.198 10 false ECM 6.104,1.229 6.646,1.583 0.542,0.354 10 false Duty Control

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) When either of the following conditions is met (1 trip detection logic):
·

Air fuel ratio sensor circuit malfunction

·

The resistance of the air fuel ratio sensor element is 250 Ω or higher for 5 seconds or more.


Main trouble area: Open in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

Air fuel ratio sensor heater

·

Air fuel ratio sensor heater circuit

·

ECM


Comes on DTC stored
P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) Air fuel ratio sensor circuit low (sensor 1)
(1 trip detection logic)
Main trouble area: Open in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

Air fuel ratio sensor heater

·

Air fuel ratio sensor heater circuit

·

ECM


Comes on DTC stored
P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) Air fuel ratio sensor circuit high (sensor 1)
(1 trip detection logic)
Main trouble area: Short in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

Air fuel ratio sensor heater

·

Air fuel ratio sensor heater circuit

·

ECM


Comes on DTC stored
P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) Air fuel ratio sensor circuit low (sensor 1)
(1 trip detection logic)
Main trouble area: Open in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

Air fuel ratio sensor heater

·

Air fuel ratio sensor heater circuit

·

ECM


Comes on DTC stored
P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) Air fuel ratio sensor circuit high (sensor 1)
(1 trip detection logic)
Main trouble area: Short in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

Air fuel ratio sensor heater

·

Air fuel ratio sensor heater circuit

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2237
·

AFS Voltage B1S1

·

Exhaust Temperature B1S1


P2238
P2239
P2252
P2253

MONITOR DESCRIPTION

The air fuel ratio sensor outputs a voltage in proportion to the air fuel ratio. If impedance (alternating current resistance) or voltage output of the sensor deviates greatly from the standard range, the ECM interprets this as an open or short malfunction of the air fuel ratio sensor circuit.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2237 Ignition switch ON for 7 seconds
P2238
P2239
P2252
P2253

WIRING DIAGRAM

A284162
3.469,1.667 4.792,2.073 1.323,0.406 10 false Air Fuel Ratio Sensor 4.667,0.417 4.885,0.604 0.219,0.188 10 false 1 1.094,1.823 1.792,2.01 0.698,0.188 10 false EFI NO. 2 1.583,3.688 2.771,3.885 1.188,0.198 10 false EFI-MAIN NO. 2 1.219,5.865 2.292,6.063 1.073,0.198 10 false Battery 1.073,4.667 2.26,4.865 1.188,0.198 10 false EFI-MAIN NO. 2 5.396,0.563 5.854,0.76 0.458,0.198 10 false B76 5.396,1.333 5.854,1.531 0.458,0.198 10 false B76 5.406,2.021 5.865,2.219 0.458,0.198 10 false B76 5.417,3.031 5.875,3.229 0.458,0.198 10 false A61 5.417,0.365 5.875,0.563 0.458,0.198 10 false 104 5.427,1.146 5.885,1.344 0.458,0.198 10 false 125 5.417,1.854 5.875,2.052 0.458,0.198 10 false 126 5.448,2.844 5.906,3.042 0.458,0.198 10 false 45 3.552,0.427 3.771,0.615 0.219,0.188 10 false 2 3.583,1.229 3.802,1.417 0.219,0.188 10 false 4 4.667,1.208 4.885,1.396 0.219,0.188 10 false 3 1.313,3.24 1.531,3.427 0.219,0.188 10 false 1 1.302,4.094 1.521,4.281 0.219,0.188 10 false 2 0.802,3.229 1.021,3.417 0.219,0.188 10 false 3 0.771,4.094 0.99,4.281 0.219,0.188 10 false 5 5.708,0.469 6.323,0.667 0.615,0.198 10 false HAF2 4.219,0.438 4.833,0.635 0.615,0.198 10 false HAF2 5.719,1.219 6.333,1.417 0.615,0.198 10 false AF2+ 5.729,1.885 6.344,2.083 0.615,0.198 10 false AF2- 5.729,3.021 6.344,3.219 0.615,0.198 10 false MREL 3.771,1.198 4.385,1.396 0.615,0.198 10 false AF2- 4.229,1.188 4.844,1.385 0.615,0.198 10 false AF2+ 3.781,0.448 4.396,0.646 0.615,0.198 10 false +B 3.448,1.51 4.063,1.708 0.615,0.198 10 false B8 1.042,5.323 2.229,5.521 1.188,0.198 10 false FL MAIN 6.146,4.854 6.813,5.292 0.667,0.438 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B8-3 (AF2+) - B76-125 (AF2+) Always Below 1 Ω
B8-4 (AF2-) - B76-126 (AF2-) Always Below 1 Ω
B8-3 (AF2+) or B76-125 (AF2+) - Body ground Always 10 kΩ or higher
B8-4 (AF2-) or B76-126 (AF2-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE AIR FUEL RATIO SENSOR

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.REPLACE AIR FUEL RATIO SENSOR

Result:
Proceed to
NEXT



NEXT

3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Warm up the engine.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

f.

Drive the vehicle

HINT:

Make sure that the exhaust gas temperature (Exhaust Temperature B1S1) is 200°C (392°F) or higher.



g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

h.

Confirm that the DTC is not output again.


Result:
Proceed to
OK
NG



OK

END

NG

4.REPLACE ECM
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Warm up the engine.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

f.

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

HINT:

Make sure that the exhaust gas temperature (Exhaust Temperature B1S1) is 200°C (392°F) or higher.



g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END