Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0046807 ECD SYSTEM(for DPF) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0107  Manifold Absolute Pressure / Barometric Pressure Circuit Low Input  P0108  Manifold Absolute Pressure / Barometric Pressure Circuit High Input  


DESCRIPTION

A208461
0.417,0.407 0.563,0.57 0.146,0.163 10 V 0.155,0.768 0.544,0.924 0.389,0.156 10 3.586 0.155,1.824 0.544,1.98 0.389,0.156 10 0.386 0.989,2.28 1.17,2.43 0.181,0.149 10 40 2.282,2.28 2.55,2.43 0.267,0.149 10 320 0.942,2.628 1.209,2.778 0.267,0.149 10 300 0.942,2.796 1.327,2.945 0.385,0.149 10 (11.8) 2.244,2.796 2.629,2.945 0.385,0.149 10 (94.5) 2.852,2.796 3.293,2.945 0.441,0.149 10 (in.Hg) 2.852,2.476 3.293,2.625 0.441,0.149 10 mmHg 2.852,2.029 3.13,2.182 0.278,0.153 10 kPa 2.852,2.196 3.234,2.349 0.382,0.153 10 (abs) 2.244,2.628 2.574,2.778 0.33,0.149 10 2400 1.324,2.995 2.151,3.172 0.826,0.177 10 Air Pressure

The manifold absolute pressure sensor detects the intake manifold pressure. The ECM determines the basic injection volume and injection advance timing based on the voltage output by the manifold absolute pressure sensor.

The manifold absolute pressure sensor monitors the absolute pressure inside the intake manifold (default is 0 kPa [0 mmHg, 0 in.Hg]). As a result the ECM controls the air-fuel ratio at the proper level under any driving conditions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input After the engine is started, condition (a) continues for more than 0.5 seconds (1 trip detection logic):
(a) Manifold absolute pressure sensor voltage is 0.1 V or less.
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored
P0108 Manifold Absolute Pressure / Barometric Pressure Circuit High Input After the engine is started, condition (a) continues for more than 0.5 seconds (1 trip detection logic):
(a) Manifold absolute pressure sensor voltage is 4.8 V or higher.
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0107
·

MAP

·

Atmosphere Pressure


P0108

HINT:
·

If DTC P0107 and/or P0108 is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power


·

When DTC P0107 or P0108 is stored, check the intake manifold pressure by entering the following menus: Powertrain / Engine and ECT / Data List / MAP.

Reference
Intake Manifold Pressure Malfunction
Approximately 0 kPa
·

Open in VCPM circuit

·

Short in PIM circuit to ground

·

Short in PIM circuit to EPIM circuit


250 kPa (1875 mmHg, 73.8 in.Hg) or higher
·

Short in VCPM circuit to PIM circuit

·

Open in PIM circuit

·

Open in EPIM circuit





CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0107 After engine is started for 2 seconds, race engine for 1 second
P0108

WIRING DIAGRAM

A165731
0.521,2.229 2.76,2.406 2.24,0.177 10 Manifold Absolute Pressure Sensor 6.031,2.25 6.458,2.427 0.427,0.177 10 ECM 1.604,1.573 1.76,1.719 0.156,0.146 10 E 1.479,1.031 1.76,1.177 0.281,0.146 10 PIM 1.521,0.448 1.76,0.594 0.24,0.146 10 VC 5.698,1.573 6.073,1.719 0.375,0.146 10 EPIM 5.698,1.031 5.979,1.177 0.281,0.146 10 PIM 5.698,0.448 6.125,0.594 0.427,0.146 10 VCPM 1.844,0.531 1.969,0.708 0.125,0.177 10 3 1.844,1.104 1.969,1.281 0.125,0.177 10 2 1.844,1.656 1.969,1.833 0.125,0.177 10 1 5.406,0.531 5.594,0.708 0.188,0.177 10 93 5.344,1.104 5.604,1.281 0.26,0.177 10 117 5.417,1.656 5.594,1.833 0.177,0.177 10 72 6.031,2.052 6.302,2.229 0.271,0.177 10 B76 0.51,2.063 0.781,2.229 0.271,0.167 10 B47

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).


HINT:
·

If DTCs relating to different systems are stored and they share terminal E2 as their ground, check this ground circuit first.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (MAP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.

Powertrain > Engine > Data List
Tester Display
MAP
50003 61 314

d.

Read the value.

OK:

Same value as the actual atmospheric pressure.


HINT:
·

Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. Varies by weather (high atmospheric pressure, low atmospheric pressure).

·

Also, check "Atmosphere Pressure" in the Data List.




Result:
Proceed to
OK
NG



OK

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B47-2 (PIM) - B76-117 (PIM) Always Below 1 Ω
B47-3 (VC) - B76-93 (VCPM) Always Below 1 Ω
B47-1 (E) - B76-72 (EPIM) Always Below 1 Ω
B47-2 (PIM) or B76-117 (PIM) - Body ground Always 10 kΩ or higher
B47-3 (VC) or B76-93 (VCPM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.
A204467
0.573,1.042 1.01,1.302 0.438,0.26 1.49,1.281 1.198,1.698 false 1.948,1.281 2.188,1.688 false 1.094,1.729 1.208,1.885 0.115,0.156 10 E 2.208,1.698 2.479,1.854 0.271,0.156 10 VC 0.24,0.219 0.427,0.385 0.188,0.167 10 *a 0.677,1.094 0.958,1.24 0.281,0.146 10 B47
*a Front view of wire harness connector
(to Absolute Pressure Sensor)


Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B47-3 (VC) - B47-1 (E) Ignition switch ON 4.75 to 5.25 V



d.

Reconnect the manifold absolute pressure sensor connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

6.REPLACE ECM
4.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS
5.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the GTS off.


g.

Start the engine.


h.

After the engine is started for 2 seconds, race the engine for 1 second.


i.

Turn the GTS on.


j.

Confirm that the DTC is not output again.


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

l.

Input DTC P0107 or P0108.


m.

Check the DTC judgment result.

HINT:

If STATUS is INCOMPLETE or N/A, race the engine for 1 minute, and then idle the engine for 5 minutes.


Result:
Proceed to
ABNORMAL
NORMAL




ABNORMAL

6.REPLACE ECM

NORMAL

END

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the GTS off.


g.

Turn the ignition switch to ON for 3 seconds and turn the GTS on.


h.

After the engine is started for 2 seconds, race the engine for 1 second.


i.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0107 or P0108.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, race the engine for 1 minute and then idle the engine for 5 minutes.



Result:
Proceed to
NEXT



NEXT

END